Search Documents

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

As a number of underground fires have unfortunately happened in the Broken Hill mining district, the writer trusts that a paper dealing with such a subject may prove of interest. To simplify matters, the subject is classed under three mainheadings- I Origin of fires; II Methods of subduing them; III Precautions to minimize the risk of their occurrence.Underground fires may be started in three ways - arson, spontaneous combustion, or carelessness.With regard to the first-mentioned cause, direct evidence is usually lacking to prove that any fire has been caused maliciously; Though definite proof of spontaneous combustion having been the cause of a mine fire has not been brought forward, nevertheless it should be considered, especially in the case of sulphide ore bodies of a more or less friable nature. The writer has been informed on reliable authority that in an open stope on the...

Jan 1, 1911

By Davis A, Song J

A review of the literature indicated that several studies have been reported on the dissolution of gold using iodide/iodine, bromide/bromine leaching systems. Although the reagent costs are much cheaper for chloride/chlorine (or hypochlorite) this system has not been fully evaluated. This study was conducted to evaluate the fundamental chemistry of the chloride/hypochlorite leaching system. The CHEMIX program was used to model the stability of various gold species existing in the solution. The gold dissolution rate at different conditions was determined using gold strips immersed in various mixtures of chloride/hypochlorite. Leaching experiments were conducted to test the extraction of gold from various ores (oxidised and copper-gold ores), showing a promising prospect for this technique in various applications.

Jan 1, 1992

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By Heesteman LJL, Turvey DJ

The Mangani mine in West Sumatra is historically one of the most important precious metal mines in Indonesia, although the past production by World standards is small, totall- ing 5.66 tonnes gold and 242 tonnes silver. The geology is dominated by a distinctive NW-SE graben structure formed by dextral splay faults from the Sumatran Fault System. Quartz- rhodochrosite-rhodonite-Ag-Au veins are hosted by Tertiary pyroxene andesite volcanics and quartz-phyllite conglomerates, on N-S tensional fractures which intersect the Mangani graben. Intrusive rocks include andesitic dykes, pyroxene microdiorite, and hornblende granodiorite. Quartz-epidote-pyrrhotite alteration is related to concealed intrusions. Precious metal vein mineralization is characterized by: high Ag/Au ratio (>25); complex sulphide mineralogy of Fe, Mn, Ag, Cu, Pb, Zn, As, Se and the occurrence of Sn as stannite; low total sulphide content (

Jan 1, 1987

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

Au airway hteat and moisture exchange .,Jgorithm is described which is generalised to suit most mining situations and can be run separately on a microcomputer or used within a network simulation. The main difference between this technique and other simplified methods is that a non-uniform boundary condition is allowed for. This permits radiative heat transfer between surfaces of different wetness in addition to evaporative and convective heat and mass transfer.

Jan 1, 1988

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

I offer some comments which might complement the valuable recent paper by De Angelis et al (1987), on the newly discovered nickel-copper deposit at Radio Hill.The authors have accepted subdivisions and correlations by Hickman (1977, 1983) although they are disputed (Fitton, Horwitz and Sylvester, 1975; Horwitz, 1979; Horwitz and Guj, 1986).Also, in my opinion, more plausible correlations of the Sholl Belt with Whim Creek Belt have been shown, but not discussed, in Hudson and Horwitz (1986, Figure 1). Our suggested correlations and subdivisions have appeared in publications and reports which are not readily available, but it is gratifying to note that many of the observations and conclusions of De Angelis et al are consistent with our conclusions of the Whim Creek Belt.The units of the Sholl Belt (of Hickman, 1983), between the Sholl Fault (Shear Zone) and the overlying Mt Bruce Supergroup to the south, equate well with units of the Whim Creek Belt. A basalt, characterised by an abundance of vesicles and similar in many ways to the Wararnbi Basalt of Fitton, Horwitz and Sylvester (I975), is well developed at the base of the succession, particularly in the southern part of the area (Figure 1). It is overlain by acid tuffs (locally metamorphosed, such as at Whundoo Mine) and associated acid and mafic lavas, similar to those of the Mons Cupri area. The mafics in the succession are marked by the absence of the numerous cherty sedimentary intercalations, such as the Marble Bar Chert, which occur in the Warrawoona Group; and they also lack the intense chertification that is prevalent in all parts of the proven areas of Warrawoona Group rocks.The Whim Creek Group is overlain, locally unconformably (two to three km east of Mount Negri), by the Negri Volcanics which include here the Louden Volcanics (unit Abu of Hickman, 1977), (Horwitz, 1979). The negri volcanics are an alternating sequence of variolitic and quench textured lavas not dissimilar to the highest units of the Sholl Belt (Figure 1). They range from high-Mg basalt to tholeitic andesites (Glikson et al, 1986, pp 79 and 84). The whole succession of the Sholl Belt is estimated to be of the order of four km in thickness, more consistent with the two km thick (Horwitz, 1979, Figure 1) Whim Creek area sequence than with the much thicker Warrawoona Group sequences. The Whim Creek Group (including the Negri Volcanics) is considered to be a widespread grouping (Fitton, Horwitz and Sylvester, 1976; Horwitz, 1979; Horwitz and Guj, 1986) which is prevalent in the northern part of the Pilbara Craton. It is considered by these authors to include the Mallina Formation turbidites of the trough area of Ryan (1965). One component, the Mons Cupri Volcanic, is about 2.95 Ga (Richards and Blockley, 1984). Between the Sholl Fault and Egina, the Whim Creek Group is intruded by large ultrarnafic to granophyric ills of the Millindinna Complex (Fitton, Horwitz and Sylvester, 1975), dated at 2.860 ± 002 Ga by Gulson and Korsh (1983) near the Sherlock River (south side of Caines Well Granite area). The Millindinna Complex has been equated to the same magmatic episode as the layered complexes of the Sholl Belt by Fitton, Horwitz and Sylvester (1975, p 20).

Jan 1, 1988

By Wernick B. J

Recently, the Environmental Engineering Laboratory of the Chamber of Mines of South Africa Research Organization has made signifi- cant progress in the development of more accurate algorithms for assessing heat flow in gold mines. These algorithms have been incor- porated into an overall computer program, ENVIRON, which enables the complete thermo- dynamic analyses of mine ventilation and cool- ing systems to be carried out. Recently, efforts have concentrated on the development of an expert computer system which will guide engineers in the process of selecting the most appropriate environmental control strategy.

Jan 1, 1988

By E Wargem

The conventional method of underground mining involves a process known as drilling and blasting to excavate valuable ore bearing minerals through the load and haul process. Drilling and blasting processes are completed for both the development of the tunnels used to access the orebody and for mining out the orebody itself. The former being called development drilling and blasting, and the latter production drilling and blasting. In either development or production drilling and blasting, the effective recovery will be largely reliant on the extraction of the initial void created in each blast cycle. In development tunnelling, the initial void is commonly known as a Burn Cut. The initial void created in production drilling and blasting has many names such as a Slot, Winze, Rise or Raise. There are drill patterns and charge designs used to create these initial voids in the production cycle. This paper discusses common slot or winze designs for production drilling and blasting; and various critical design criteria for these. The document also aims to provide a process for completing desktop reviews of current patterns employed on-sites and provides an initial guide in a process for improving the recovery of a slot, winze, rise or raise in underground mines.

Mar 29, 2023

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By Walter GW

Rock mass classification systems for stable excavation design have been studied. The parameters which are important in such a classification system and those which should be included in a classification system formulated to predict explosive fragmentation behaviour are briefly reviewed and compared. There is significant overlap in the data requirements for excavation design and explosive blast de- sign. Recently there has been a trend to ob- tain some of the data required for excavation design by the use of both field and laboratory seismic investigations. The theory of seismic techniques is summarised and the results of seismic investigations carried out for excava- tion design are reviewed. On this basis it is considered that seismic techniques have the potential to be used for data collection prior to blast design. A programme designed to de- velop such techniques and which includes both field and laboratory experimentation is Presented.

Jan 1, 1978

By Tukkimies M

During the late-1980s crawler-mounted crusher units established their position in the aggregates industry. Between 1986 and 1994 about 700 units were delivered to customers all over the world for surface operations, mainly in Scandinavia and central Europe. The crawler-mounted units are popular among smaller crushing operators because they are versatile and easy to move between sites. In large quarries the greatest benefit is obtained by combining a primary crawler-mounted crusher unit with mobile belt conveyors which eliminates the need for costly haulage by dump truck. Savings of up to 40 per cent in production costs prior to secondary crushing have been achieved. Today the environmental aspect in quarrying is assuming ever greater importance. Besides being costly the dump trucks are also the major source of dust and exhaust fumes within a quarry. A complete face crushing system consisting of a crawler-mounted crusher unit and mobile belt conveyors can be electrically driven and can be equipped with dust encapsulation and dust collectors. A mobile crushing unit is not a new idea. From the mid-1950s onwards the mobile and self-propelled units have been built equipped with crawlers, tyres or walking mechanisms, with weights usually of 500-1000 t. Due to their massive size these unit are not mobile in the same way as the today's mobile units. It is not feasible to move them more than a few times a year unlike today's fully mobile units which are often relocated once an hour. This means that the massive units can not continuously follow the production face and their loading always requires a certain amount of haulage. Today the mining industry is facing new challenges. With low mineral prices and high labour costs, increasing productivity is essential for survival. New standards are also being set for the labour safety and the environment. Large research programs have been launched to meet these challenges. However, technology which can partly solve these problems already exist and is only waiting to be introduced into underground applications as well - the mobile crushing unit followed by belt conveying. As in surface operations the elimination of truck haulage also brings considerable savings in operating costs in underground mines and reduces the amount of dust and exhaust gases generated. An additional benefit especially in underground applications is improved safety. In an underground mine most accidents are caused by moving vehicles.

Jan 1, 1995

Coal mining safety and health legislation is more than typical of safety legislation which has been born of adversity. Indeed, in the main it has been the child of disaster. Requirements which now appear obvious were indeed only occasioned by either social injustice or more commonly by great disasters. Even then changes were often made only after months or years of deliberation by committees. Early mining legislation in New South Wales benefited from the experience in Great Britain. The pioneers of our industry were miners from there and brought with them the basic British legislation, so we started with knowledge gained the hard way. A review of accidents statistics provides a measure of the effectiveness of mine safety legislation, but unfortunately rules cannot control human nature. Miners, managers and inspectors must work as a team to make mines safe and new legislation in New South Wales is planned to this end.

Jan 1, 1975

By Kramadibrata S

Over the years many attempts have been made to develop a means of assessing the excavatability of rock. Most of them are based on an empirical rating system while some authorities still propose the use of seismic velocity as a direct predictor of the rippability of a rock mass. On the other hand there are a number of classical models which have been developed to define the cutting force required at the pick or tooth of continuous miners.While these methods have been applied with various degrees of success to the design of excavation systems there is no generally acceptable method of defining the excavatability or cuttability of a rock mass in terms of the machine power required to generate a particular rate of production.The authors have attempted to overcome this deficiency by recording the intact and rock mass properties at a number of surface mines where continuous miners were in use and to use this data to examine the relationships between the relevant dimensionless groups developed from a dimensional analysis of the problem.The results obtained are encouraging and it appears that this new approach to the problem could lead to civil and mining engineers having a means of predicting the cutting power required to excavate rock at a given rate at any site.While this paper does not include a review of past work it refers to a number of key publications which will give the reader an excellent introduction to the subject.It is important to point out that the research work reported in this paper is part of a doctoral research project at Curtin University of Technology on the Influence of Intact Rock and Rock Mass Properties on the Design of Surface Mines. One of the major objectives of this project is to explore the possibility of developing a technique for predicting the excavatability of rock in surface mines at the design stage.This paper therefore commences with a brief reference to the continuous surface miners in use at the test sites followed by some original work by the authors in applying Dimensional Analysis to analyse the macro-performance of mechanical excavators. Following an analysis of the experimental data the authors validate the wider use of the model by referring to its successful application in predicting the power required to excavate rock by continuous surface miners at other sites.

Jan 1, 1995