Search Documents

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By D C. Curry, M F. Young

Many flotation operations need to improve liberation to increase recovery, yet often plant operators are concerned that finer grinding will produce æslimesÆ with low flotation recovery. Yet simple circuits can be designed to give good liberation and excellent fines recovery. The economics of fine grinding has changed fundamentally with new stirred milling processes like the IsaMill. This has also transformed flotation design due to the clean surfaces produced in the inert grinding environment and the narrow size distribution produced by the IsaMill. Past poor experiences with æovergrindingÆ in flotation circuits was often due to the wide size distribution and the degradation of mineral surfaces produced by conventional devices using steel media, like ball mills and tower mills. The correct practice is to design both grinding and flotation together to suit the liberation characteristics of the ore. This may result in several stages of grinding and flotation, recovering mineral as soon as it is liberated, then applying further grinding energy only to those particles that still need liberation. Flotation then occurs in relatively narrow size bands and with minerals with similar liberation characteristics. Though the circuit may look more complex on paper, in reality it is far simpler to operate since each section performs predicably. Circuit design also needs to address materials handling. Finer particles affect froth handling and dewatering, but can still be easily handled by standard products with careful attention to design of launders, pumps and pumpboxes, and de-aeration before thickening and filtering. Excellent examples of designing circuits to include ultrafine grinding include Mt Isa and McArthur River (MRM). In the last decade these operations have produced over ten million tonnes of concentrate with an average grain size below 10 ¦m and above 80 per cent recovery. At Mt Isa, zinc recovery was increased by ten per cent by applying fine grinding to existing poorly liberated streams. In fact, grinding finer in the IsaMill actually improved the recovery of fine particles by ten per cent, and maximum particle flotation recovery occurs for 10 ¦m particles. A more recent example is the flotation of Platinum Group Metals (PGMs). The use of conventional ball or tower milling to improve liberation is severely limited by the impact of commonly associated chromite on classification, and degradation of flotation performance by the steel grinding environment. The ability of open circuit IsaMills to deliver a narrowly sized ultrafine product with clean mineral surfaces is transforming the design of platinum flotation circuits. The science and practice of fine-grained flotation is now thoroughly proven. The availability of the 2.6 MW IsaMill has made ultra fine grinding a practical tool for flotation plant design. It is expected to become a standard choice for future applications of both fine-grained ores and for minerals with difficult flotation characteristics.

Jan 1, 2005

The published safety policy of Mount Isa Mines Limited, together with details of the organisation and control techniques adopted by management to pursue an active safety programme within the company, is presented. The importance of communication by management through the organisational hierarchy and procedures instituted to ensure rapid and concise feedback on safety concerns are detailed. The paper also describes the role of the occupational health department and safety committees in assisting management to monitor the safety effort of supervisors and employees. Current safety performance levels are tabled together with details of some aspects of the programme on which safety effort will be concentrated in the future.

Jan 1, 1975

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

The New England Fold Belt forms the easternmost and youngest section of the Tasman Fold Belt System of eastern Australia. From middle Palaeozoic to Early Cretaceous time it was the site of extensive episodic calc-alkaline magmatism related to W-dipping subduction. The oldest rocks may have formed at least partly in a volcanic island arc, but from the Late Devonian, the fold belt developed as a convergent Pacific-type continental margin. For Late Devonian-Carboniferous time, parallel belts representing continental margin volcanic arc, forearc basin and subduction complex assemblages can be recognised. Major dextral transform faulting may have offset parts of the fold belt in the Late Carboniferous. In addition, some structural blocks which appear to be out of place in the overall palaeogeographic setting are possible exotic or suspect terranes. A great variety of lode deposits ranging in age from middle Palaeozoic to Early Cretaceous is present in the New England Fold Belt. The vast majority of these are related to emplacement of extensive granite plutons and eruption of continental silicic volcanics in Late Permian-Late Triassic time. However, volcanogenic massive sulphides and volcanic hosted epithermal gold-silver deposits in older rock sequences include one major orebody (Mount Morgan) and several important ones (Mount Chalmers, Cracow, Silver Spur, Cangai and Halls Peak). Some problematical deposits are best classified as metamorphic-hydrothermal. These include gold-bearing quartz reefs and stockworks in sedimentary host rocks, the most important of which are at Gympie, and antimony-gold- tungsten mineralisation in the New England area, mainly at Hillgrove.

Jan 1, 1987

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

Palaeomagnetic work on the red beds of the Hervey Group from central N.S.W., and on the Mount Eclipse Sandstone from the Ngalia Basin, Central Australia, reveals a pre-deformational magnetization from the Hervey Group, which indicates a semi-equatorial palaeolatitude during the latest Devonian or earliest Carboniferous and a syn-deformational magnetization from the Mount Eclipse Sandstone which places Australia at a palaeolatitude of about 70¦ ¦ 20¦S during the early Late Carboniferous. By comparison with the existing data from Australia, the new results indicate that: (1) Australia (and thus eastern Gondwanaland) underwent a rapid southward movement of about 60¦ during the late Early and early Late Carboniferous, (2) the Lachlan Fold Belt has been part of cratonic Australia since at least latest Devonian or earliest Carboniferous, and (3) the New England region and cratonic Australia were at a similar palaeolatitude during earliest Carboniferous, but they may have undergone the rapid southward movement separately.

Jan 1, 1987

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987

Performance trials followed the commissioning of three large mine fans at Mount Isa in 1965. Actual performance characteristics were determined. These were in good agreement with predicted performance. Piezometer rings for volume flow and pressure measurement were calibrated, and the performance of some aerodynamic components of the installation was studied.Test equipment, preparation, and conditions are described.

Jan 1, 1967

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005

Estimation of the semi-variogram is basic to the geostatistical processing of data. The most widely used arithmetic average estimator is here employed with various sampling patterns to calculate experimental semi-variograms in a deposit which is simulated to have a defined semi-variogram. Percentage differences between theoretical and experimental semi-variograms are reported.

Jan 1, 1984

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

By P Hucker, E Hall

Harmony Gold operates the Mount Marion underground gold mine near Kalgoorlie, Western Australia. The mine consists of two ore zones, East and West, and mining of these zones is currently conducted using the sublevel caving method. When mining commenced in the Western zone, the span was insufficient to induce caving of the country rock above. Dyno Nobel, together with Harmony and 360 Drilling, developed an innovative drill and blast solution in order to promote cave propagation and improve the safety of personnel at the operation. The solution involved a series of shallow angle drill holes up to 90 m into the hanging wall of the West zone. These were charged with Titan« 7000 underground bulk emulsion and the HotShotÖ electronic initiation system. The blast used over seven tonnes of emulsion and 46 detonators and achieved the desired result without damaging nearby mine infrastructure.

Jan 1, 2007