Search Documents

British Coal's Selby Complex is the newest producing mine in the United Kingdom. The reasons behind its origins, planning and design are explained. Some detail is given of equipment used, with the emphasis being placed on the unique features of its layout. The entire project has been planned and constructed over many years and the design has consequently changed, principally in response to the geology of the coalfield and improving technology. In spite of many totally unexpected difficulties, the mine, which is not yet in full production, has the highest productivity in the United Kingdom.

Jan 1, 1991

By Mance G

Today there are many different techniques of soil remediation used in Australia and throughout the world. This paper considers the thermal desorption remediation technique and, in particular, the application of high temperature filtration to the process. The thermal desorption technique involves the treatment of hydrocarbon (oil, petrol, etc) contaminated soil. The process involves heating the soil in a retort or kiln to drive off the volatile organic contaminants. The exit gas stream from the retort is subsequently passed through an after burner to thermally oxidise the hydrocarbons. This technique produces soil and combustion gas streams which are free of hydrocarbons. Due to the heating and agitation of the soil within the retort, soil particles become entrained in the hot gas stream. To avoid the blockage and fouling of the system's interim ductwork and the afterburner, high temperature filtration technology has been applied to remove these soil particulates without cooling the gas Stream.

Jan 1, 1995

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By Lindner E, Bosio M

South Australian coals are all low in rank and generally poor in quality, with difficult combustion characteristics. This circumstance makes the selection of a fuel source for future power generation difficult, requiring careful study and detailed analysis of the various alternatives. Combustion characteristics can have a significant effect on plant design and costs, and need early attention in any exploration and evaluation programme. The physical location of the deposits, often remote from established infrastructure and centres of population, is also a major factor in the ultimate cost of power at the poirl use.

Jan 1, 1977

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

By Jephcott S

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralized bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulphides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralization. The geochemistry of the deposit has been investigated with respect to the stratigraphio column and mineralogy of the sediments.

Jan 1, 1980

Rifting and transfer faulting in the Late Cretaceous to Early Tertiary resulted in the formation of the Bundaberg Trough and Wallaville Basin and deflected the margin of the Maryborough Basin southwestward between the Kolan and Burnett Rivers. During the Cainozoic, three periods of volcanic activity occurred in the Bundaberg-Gin Gin area. The oldest of these periods, Paleocene to Early Eocene, resulted in the outpouring of tholeiitic lavas. During the Late Miocene to Pliocene, undersaturated alkali basalts generated at depths of from ca. 35 to 55 km were emplaced. These lavas were followed in the Pleistocene by the alkaline Hummock and Berrembea Basalts. The loci of eruption of all of these lavas were controlled by the intersection of the transfer fault system and pre-existing north to northwesterly trending faults in the Bundaberg-Gin Gin area.

Jan 1, 1990

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

Until 1937, the mining of ore was carried out by conventional methods, using pneumatic drills and standard drill steel. The adoption of the diamond drill, formerly used for exploration work, for blast hole drilling in stopes, was first developed by Noranda Mines Limited, Noranda, Quebec, although it had been used previously in Northern Ontario and Western United States, to remove weak pillars and ore remnants left by conventional methods. Previous to the adoption of the diamond drill method at Noranda, a sub-level benching system of stoping was used. Sub-levels were driven at 35 ft. intervals and the benches drilled off by pneumatic drills using sectional steel. Results were very satisfactory, in sulphide ore, where the drilling was comparatively easy, but in the harder rhyolitestopes the footage drilled per machine-shift was only half of that obtained in the sulphide stopes, and owing to the high gauge loss, there was often difficulty in drilling holes to the required depth. This led to trials with the diamond drill for this type of work. While the cost per foot was more than with sectional steel, an appreciable saving in development work could be made by increasing the sublevel interval from 35 ft. to 60 ft., and stope widths from 60 to 100 ft. This saving, together with the increase in blasting efficiency, resulted in a substantial reduction in overall costs.CONDITIONS FOR SUCCESSFUL APPLICATIONWhile long diamond drill blast-hole mining has widespread application, there are certain conditions which appear to be desirable, if not absolutely necessary, for its successful use.

Jan 1, 1946

Strata bolting/dowelling reinforcement techniques are being reintroduced into the mines of the National Coal Board. There are strong reasons for the selection of the full hole anchorage principle of bolting and for the development of the wood/resin dowel. There are strong reasons also for the measurement of strata bed separation as the method of assessing the effectiveness of a roof bolting system. There are several designs of bolts. Instruments have been developed for investigation and control purposes. Different drilling and bolting machines have been employed in trial sites. In addition comparative laboratory model work has been conducted on simple non-bolted and bolted systems.

Jan 1, 1971

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

By A Robertson

Australia has been slow in adopting the use of underground space as a part of our urban planning process. Australia has one of the highest levels of tunnel advance per capita per annum in the world, yet the use of underground space in our cities appears difficult for our planners and politicians to comprehend, not withstanding the general availability of good quality rock and contractor expertise in Australia. However, the lack of space in our urban areas is being highlighted as our major cities expand outwards and people and businesses gravitate towards city centres. Typical potential underground space uses include car parking, self-storage and archiving facilities, water storage, underground quarrying, small industrial facilities and another layer of traffic (electric and fuel cell) and services network. Historically, blasting in high density population areas has resulted in blast vibrations and blast overpressures exceeding the limits, which in some case have been set extremely low in terms of peak particle velocity (PPV). This makes conventional blasting difficult, often requiring low charge weights per delay and associated small blast sizes and slow advance rates. However, the introduction of new technologies, such as computer aided drilling, electronic delays and low-energy explosives has made this task considerably easier. Although more expensive than conventional blasting, excavation by blasting using these products and technologies in relatively good quality ground is believed, in most cases, to be less than the cost of mechanical excavation. In this paper, the authors look at innovative trends in underground quarrying, underground commercial space and tunnelling and put forward their concept of future excavation demand, future product requirements and technical specifications to the drill and blast community.

Jan 1, 2007

By A Cornelius, P Connor, S Fraser

Iron ore mining is a major source of export income for Australia. However with the decreasing reserves of high-grade, low-phosphorus hematite ore, there is mounting pressure to provide consistent mineralogical ore grade. Enhanced 3D characterisation and modelling are crucial to respond to these exigent requirements. To tackle this problem a revolutionary mine-based, imaging system (based on Visible Near Infrared û Short Wave Infrared reflectance spectroscopy û VNIR-SWIR) has been developed. This innovative, CSIRO-built prototype produces mineralogical maps that will have a major impact on ore grade characterisation. Australian iron ore companies will benefit immensely by pioneering this emerging and unique mining technology. The significance of VNIR-SWIR reflectance spectroscopy is well demonstrated with field portable spectrometers and airborne hyperspectral systems. At the mine-scale level, this newly developed imaging system will allow accurate and objective mineralogical mapping of mine faces and benches with very closely spaced sampling. These spectral mineral maps will improve deposit delineation and bring accurate and objective ore grade characterisation that will minimise drilling and enhance ore recovery. This will in turn lead to cost saving and better long-term block model planning. This system will also improve safety for mine geologists in providing mineralogical information at a distance, avoiding the need for any close contact with the mine face. The mine imaging concept is a logical response to the industry need for automatic and objective tools for sustainable and future mining practices.

Jan 1, 2002

By Moore J

Gunpowder Copper Ltd is using in-situ leaching to extract copper from the Mammoth sulphide ore deposit in north-west Queensland. To increase metal recovery, ore is fragmented using conventional underground longhole drilling and blasting techniques. Although the upper levels of the orebody had previously been mined by open cut and underground methods, significant reserves of copper existed around old workings. To safely and economically recover this resource, a decision was made to fire the remaining pillars in the upper part of the mine by a single 1.37 million tonne mass blast in February 1992.This paper records the planning, design, and implementation of the Mammoth mass blast. Geological and geotechnical aspects are summarised, to explain the reasons for such a large blast. Drilling, charging and blast initiation are discussed in detail, to show how standard equipment and products were applied to a unique task.

Jan 1, 1992

The Permian rocks at Gympie were first studied as far back as 1868 in conjunction with the discovery of gold. The relationship of the Gympie Group to other sequences in the Gympie Composite Terrane is an important subject of investigations in a new mapping project of the Geological Survey Program of the Department of Resource Industries.In two areas the Gympie Group has been divided into four defined formations. They are the Highbury Volcanics (base), Ram mutt Formation, South Curra Limestone and Tamaree Formation (top) in the Gympie area, and the Mant basalt (base), Kolbar Formation, Gigoomgan Limestone and Teebar Formation (top) in the Gigoomgan area. Geochemical and lithological evidence from the basal volcanics of the Gympie Group (Highbury Volcanics, Mant basalt) indicate that they developed in an intraoceanic island arc setting. The overlying volcaniclastic sediments (Rammutt Formation, Kolbar Formation), which contain some continentally-derived material, are mainly of local derivation and shallow-water marine. A hiatus is present at the top of the Early Permian Rammutt Formation and Kolbar Formation. Following the hiatus, limestone sedimentation characteristic of a basin of restricted circulation developed in the Late Permian. There is some evidence of a hiatus between the limestone deposition of the Gigoomgan and South Curra Limestones and the overlying probable turbidite deposits of the Teebar and Tamaree Pnrmatinnc

Jan 1, 1990

By E Nettleton, A Melkumyan

Identification of geology and mineralogy in situ on the mine face is essential if mining processes are to be automated for tasks such as exploration, grading and reconciliation. Hyperspectral data acquired from field based platforms are ideally suited to these tasks, and are set to revolutionise the automated mining industry. Changing conditions of solar illumination introduces variation into the hyperspectral signal, which is unrelated to geology, complicating analysis of data. Thus, algorithms must be able to deal with changing illumination conditions and operate in a consistent and probabilistic framework, which is a prerequisite for data fusion with other sensors. To produce accurate classification maps of geology, algorithms must be developed that are effective under different conditions of illumination.The efficacy of three algorithms to classify hyperspectral data for geology mapping on vertical mine faces was assessed. These algorithms are the spectral angle mapper (SAM), and two machine learning methods operating within a fully probabilistic Gaussian process (GP) framework û the squared exponential (SE) and the observation angle dependent (OAD) covariance functions (kernel). Two experiments were done to assess the classification performances. The first determined the performance of the algorithms by classifying hyperspectral data of known rock samples acquired using a field spectrometer. The GP-based methods had a similar performance, with average accuracies and F-scores of 97 and 88 per cent (GP-OAD) and 95 and 81 per cent (GP-SE), respectively. Average accuracies and F-scores for SAM were significantly smaller (80 and 40 per cent respectively). The algorithms were then applied to hyperspectral imagery acquired from a vertical mine face at different times of the day, under very different conditions of illumination. In contrast with experiment 1, SAM and GP-OAD gave results which were superior to GP-SE and were entirely consistent with geology mapped in the field. Compared with SAM, GP-OAD was less sensitive to the effects of shadow and produced classified images that were less noisy. The GP-SE method failed to delineate even gross changes in geology on the mine face. These results show conclusively that in order to use independent training data (spectral library) to classify imagery acquired under a different set of conditions, algorithms must take into account variability in incident illumination. Measures based on spectral distance are inferior to those based on spectral angle.The OAD kernel within the GP framework (GP-OAD) is superior to the other two methods because:it provides a probabilistic framework;it is insensitive to variability in illumination within and between imagery acquired under different conditions; andit can identify and map geological zones on a vertical mine face using an independent spectral library, without a priori knowledge.

Sep 26, 2011

By McManus D

Situations where in-pit bench stripping methods are favourable are introduced. Examples from Peak Downs Mine are used as a guide to the range of methods available.A number of geological and geotechnical conditions adverse to successful in-pit bench stripping are described. In all cases bench, floor, and/or final lowwall instability can develop and compromise the economics of extraction.

Jan 1, 1992

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By Tobin GJ

Testwork carried out in the cooling water circuit at the Yabulu treatment plant of the Greenvale Joint Venturers (Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated) since 1980 has resulted in significant improvements to both fouling and corrosion control. At the same time corrosion inhibitor costs have been reduced.Acrylate-type silt dispersants were identified as the most effective means of sediment control in the circuit. An increase in the cathodic component of the corrosion inhibitor coupled with a relatively minor adjustment to water pH has yielded a two to three fold reduction in corrosion rate. It has been established that these lower corrosion rates can be sustained in the face of a 20% reduction in corrosion inhibitor addition rate. Further improvements are indicated with a change of raw water algicide.

Jan 1, 1985