Search Documents

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By W Dodson, S Dogramaci

Isotopes and hydrochemistry were used to define groundwater flow systems and better understand the hydrogeological setting of the Karijini National Park, which is in the Central Pilbara region adjacent to the Marandoo iron ore mine. Based on the stable isotope composition of the water samples, the data can be divided into two main groups. Groundwater is characterised by depleted dD and d18O, suggesting no significant evaporation effect. Surface water on the other hand is more enriched in dD and d18O due to evaporation. The relatively high concentration of Cl- compared to rainfall and depleted dD and d18O values of groundwater indicate that recharge of the aquifers is occurring during intense rainfall events when rapid infiltration occurs. Evapotranspiration then acts to concentrate ionic species prior to recharge. Relationships between the major ion concentration and catchment area, surficial Tertiary cover and distance between recharge and discharge were identified. The results show that these catchment variables combine to determine unique water chemistry for each sub catchment in Karijini National Park. The TDS concentration of the groundwater in the Marra Mamba Iron Formation that hosts the Marandoo ore body is higher than most of the water bodies surrounding the mining area suggesting significant modification or different recharge mechanisms to that of the Karijini groundwater.

Jan 1, 2009

By D Mnller, J L. Mauk

The Oblaga Cu-Au skarn deposit and porphyry prospect is located in the south-eastern edge of the Gobi Desert in western Inner Mongolia. The deposit occurs within metamorphosed middle Paleozoic volcanic, plutonic and sedimentary rocks.   Ivanhoe geologists recognise eight main rock types in the area. Calcareous sediments include conglomerate, interlayered siltstone-sandstone, and limestone. Covering the calcareous sediments is a slab of thrusted biotite granite, and above it is rhyodacitic lithic tuff which, in places, is overlain by alluvial sediments. Various plutonic rocks and related intrusion breccias have intruded these units. Monzodiorite, quartz-monzonite and monzonite tend to form thin, high-angle intrusions and the youngest andesitic intrusions are generally wider and subhorizontal.   The Oblaga Cu-Au skarn, which occurs in the calcareous sediments, shows typical prograde and retrograde mineralogy. Petrographic studies show that prograde skarn minerals have been overprinted by retrograde skarn minerals, and original host rock minerals have been texturally obliterated and completely replaced. The mineralogy of the Oblaga skarn deposit is very similar to other Cu-Au skarn deposits worldwide.   Sericitic and minor chloritic alteration occurs throughout the study area and may relate to porphyry-style mineralisation. Generally, this alteration is not intense and most rocks have retained their original texture. Geochemical analyses suggest that K-metasomatism is not widespread at Oblaga. XRD analyses suggest an upward and outward transition from sericitic to chloritic alteration.   Comparisons between Oblaga and other porphyry Cu-Au deposits worldwide show that Oblaga has very similar characteristics to deposits that have undergone sericitic alteration. However, Oblaga is special because it also has relatively intense chloritic alteration, which is uncommon in other porphyry Cu deposits described in the literature.

Jan 1, 2005

By Madgwick J. C

Bacterial leaching of museum grade chalcopyrite and chalcopyrite concentrates at low sorptive relative humidities (55-91 per cent rH) was demonstrated. Optimum release rates were 13 and 27 mg/gram/100 days copper (Cu++) at 91 per cent and 80 per cent rH and 12 and 33 mg/gram/100 days iron (Fe++) at 80 per cent and 73 per cent rH for concentrate and "pure" chalcopyrite respectively. The optimum copper release rates occurred between 73 per cent - 86 per cent rH and 30-40 mM acid concentrations. Bacterial copper leaching rates were some twenty times slower for emersed copper concentrates, at low relative humidity, compared with submerged cultures. Bacterial copper solubilization was almost quantitatively inhibited above 150 mM acid levels (< pHO.8).

Jan 1, 1984

An experimental study of the soil mechanics of brown coal showed that brown coal consolidates in the same manner as does a clay and that the theory of consolidation for soils may be applied to brown coals. Moisture content is a function of the coal type, the existing effective stress, and the stress history of the coal.The effective stress in a brown coal seam is a function of the overburden pressure, the pore stress and tectonic stresses. Stress history may be deduced from geological evidence and determined by consolidation tests. Application of these principles to the brown coal seams of the Latrobe Valley shows that the distributions of natural moisture contents are consistent with consolidation.INTRODUCTIONThe nature and geology of the brown coals of Victoria, particularly of the Latrobe Valley, were discussed in some detail by Edwards (1945, 1948), Thomas and Baragwanath (1949) and Gloe (1960). A salient feature of these studies was the distribution of moisture contents in the brown coal seams. Recent experimental work, part of a soil mechanics study of the structure and strength of brown coal, showed that moisture content variation is a reflection of consolidation phenomena in brown coal and application of the results to .field condItions verified and modified the conclusions of Edwards in his pioneer work. Further detail of this experimental work is recorded elsewhere (Rosengren, 1961).EFFECTIVE STRESS AND CONSOLIDATIONEffective stresses in soilsA saturated soil is a two-phase system, consisting of a compressible skeleton of rigid soil particles and pores filled with water, an incompressible fluid. (In this context, the terms compressible, incompressible, and rigid are relative only and refer to orders of magnitude). If this system is subjected to stress we define...

Jan 1, 1963

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

In this address I look back over the past 40 years of mineral exploration in New Zealand û essentially the period since the Second World War (ie since 1945). It was the period of my personal involvement, and indeed of the personal involvement of a number of you. Luckily it was aperiod of great interest and activity. In the previous 50 years, virtually nothing had happened, and it is kindest to draw a veil over that period. In the very important earlier 40 years (1855 - 1895) the New Zealand gold rush occurred. That must have been a fascinating, rewarding period, which has been thoroughly documented by better historians than myself. I will simply comment firstly that its mineral explorers (gold-prospectors) were very successful indeed, and found most localities of the minerals they sought, in spite of using very different methods from ours of today. Secondly, they were preceeded by one of Maori exploration, which searched for a much restricted list of minerals, but succeeded in finding virtually every locality we know of today. The explorers of both of these early periods were obviously highly successful, but, in the time available, I must restrict myself to the period since 1945. I am currently editing the effective up-dating of Gordon WilliamsÆ 'Economic Geology of New Zealand' (1974). It covers the last 12 years or so. Many of you are contributing to that volume û both as authors and as referees û and I would like to take this opportunity of thanking you all. Although this new volume excludes the energy field, many of us have been involved in it, and I am therefore including energy minerals in this review, as Williams did in 1974.

Jan 1, 1987

Research on the Thermodynamics of Siderite Roast Decomposition and the Experiment of Magnetic Roasting-Separation

Sep 13, 2010

By I M. van Waveren, F Hasibuan, M J. Crow

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Two Hg-Au occurrences west of Bangko, Sumatra occur within the West Sumatra Permian Volcanic Plutonic Arc. The Melipun Hg-Au occurrence was exploited in the past and mineralisation occurs within a hydrothermally altered cupola of a buried intrusion. The Salak Hg-Au occurrence occurs within the outcrop of the Dusunbaru pluton, likely within the remnants of a caldera in which hydrothermal mineralisation was developed. Both occurrences formed late in the history of the volcanic arc, probably between the Triassic and early Jurassic. The Melipun occurrence may have potential at depth, but that at Salak is small and lies within the area of a proposed Geopark.CITATION:Crow, M J, van Waveren, I M and Hasibuan, F, 2015. Two Hg-Au occurrences in the west Sumatra Permian volcanic-plutonic arc west of Bangko in Sumatra, Indonesia , in Proceedings PACRIM 2015 Congress, pp 573–578 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Development of Technology for Complex Uranium Ores Processing on the Flotation Process Basis

Sep 13, 2010

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By B Hayter, M Carr, K Williams, C Wheeler, W Chen

Current trends into mining iron ore have seen an increase in the exploitation of problematic orebodies that would typically be disregarded. These bulk materials cause problems within all facets of the material handling stream, from remains left in train wagons to transfer chute blockages, which can cause costly downtime to mining operations (Roberts, 1998). These problematic bulk materials are referred to as wet and sticky material (WSM) due to the adhesive and cohesive nature they possess. Their characteristics can be computationally expensive to model. With the development of discrete element modelling (DEM), in conjunction with advancement in computational power over the past decade, it is now more feasible to model WSMs into the DEM technique.This research will couple two different contact models that can represent the characteristics of a WSM. These models include the Simplified Johnson-Kendall-Roberts (SJKR) and the Easo liquid bridging contact models. The SJKR contact model is an expanded form of the classic Hertz model. This model includes the tensile forces that are in the contact zone between two bodies when they are separated, which the Hertz model failed to capture (Johnson, Kendall and Roberts, 1971). The Easo liquid bridging contact model accounts for the capillary effects and surface tension that will form between two bodies, such as that of a WSM (Soulié et al, 2006). Both of these models were coupled to give the best representation of a WSM, which was simulated using MoleculeX™ (Chen and Williams, 2017) as the software platform.Additionally, this research also investigated the adhesion of problematic iron ore samples onto impact plates under dynamic conditions. An experimental set-up consisting of an apron feeder and inclined impact plate was utilised, to gain an understanding of the way the material builds-up and the possible modes of failure that could be experienced. This was undertaken for different wall liner materials, wall liner angles and moisture contents of the iron ore samples. From this, a series of DEM calibration simulations were conducted on the experimental set-up and particle size distributions (PSD) of the iron ore samples. This enabled forming of a database of parameters, which can be scaled for on-site applications in relation to geometry of the plant and PSDs that would represent run-of-mine ores.CITATION:Carr, M, Williams, K, Chen, W, Hayter, B, Roberts, A and Wheeler, C, 2017. The dynamic adhesion of wet and sticky iron ores onto impact plates, in Proceedings Iron Ore 2017, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The pyrite-sphalerite-galena and barite orebodies at the Rosebery mine are concordant with the shale host rock and have been deformed into one system of folds with an associated axial plane cleavage. The folds are tight and overturned with east-dipping axial planes. Folds in the sulphide ore are commonly disharmonic, particularly between adjacent bands of different composition.Concentric style folds occur in the competent bands, e.g. pyrite-rich bands. Similar style folds are predominant in the less competent sphalerite-galena-rich bands and also in the shale of the host rock. The trends and plunges of the fold hinge-lines are variable but axial planes are of reasonably constant orientation throughout the mine area. The folds in the orebodies are of limited axial extent, approximating to conical folds, and are arranged in en echelon patterns. The fold system was possibly formed in one period of folding by heterogeneous strain that may have been caused by the presence of a mass of tectonically mobile sulphide ore. Lineations parallel to the ore/host rock contacts appear to reflect movement between the ore and the host rock during folding.

Jan 1, 1972

THOSE who dabble in mining are no exception to the general rule that persons who know a little of a subject are apt to think that they know all about it. Some colour may be lent to the belief that anyone may succeed in mining when we hear stories ofsuccessful diggers and others who have accidentally dropped on to something good through no foresight on their part; but we seldom hear the contra account of the far larger number who fail. Those who go more thoroughly into the subject, and take up mining as a profession, know very well that it is not one that can be carried out successfully by rule of thumb, but when they point this out to the public they are credited with trying to make it a closed profession; and outsiders are for ever trying to find out the "trade secrets," at the same time spurning the main one, which is hard study, experience, and the ability to apply their knowledge. The average mining man is not rich. When he amasses a fortune it is generally through speculation rather than professional work, thought no doubt his technical knowledge may have assisted...

Jan 1, 1910

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By Slechta J. J

An evaluation of a pilot scale Delkor horizontal belt filter at Bellambi's South Bulli Colliery showed high productivities and low moisture contents for a range of feed slurries. When treating flotation concentrate, a productivity in excess of 1000 kg/m2/hr (dry) at a moisture content of less than 22 per cent was obtained. The results indicated the belt filter had a capacity twice that of conventional drum or disc filters, and was capable of dewatering a very fine, thickened, classifying cyclone overflow slurry to an acceptable moisture content. The superior performance of this filter is discussed in terms of the factors influencing cake formation and the stratification of solids in the filter bowl of a conventional rotary vacuum drum filter.

Jan 1, 1986

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0·9 dwt., whilst for average to high-grade ore, 3·5 to 5 dwt., the figure was 1·5 to 2·0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months' research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company's workshop.

Jan 1, 1939

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992