Search Documents

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By R Burke, G Ramage, C Donnelly

Over the decades, Redpath has undertaken a multitude of tunnelling and underground excavation projects for civil and mining clients both domestically and internationally. These projects have been undertaken through varying strata conditions with differing excavation methods in remote locations and in central business districts.With the recent turbulent nature of the global financial environment, project drivers have been challenged with the emphasis being placed on methods to gain early access to orebodies, rapid development techniques, lower capital costs and reduced labour requirements to name a few.A number of mining companies seeking to achieve these objectives have commenced the journey to better understand the operational constraints, challenges and opportunities that may be available with the use of alternative excavation methods.The development of safe and effective alternative excavation methods that comply with both domestic and international mining legislation and regulatory requirements is a challenge the industry needs to embrace. Given the current cost pressures being faced by the Australian mining industry, some alternative excavation methods offer the potential for longer term sustainability and rapid development of resources.More recently work has been undertaken on a project that challenged the norm and implemented an alternative excavation method with the use of an excavator with a rotating drum cutter head.This paper will review this recent project and provide technical and operational insight into some of the challenges faced in implementing an alternative excavation method in the metalliferous industry.CITATION:Donnelly, C, Ramage, G and Burke, R, 2014. Challenging the norm – alternative excavation method in mining, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 187–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Kidston breccia pipe is situated approximately 280 km west northwest of Townsville, north Queensland. It is currently Australia's largest gold producer with production varying between 8,000 and 16,000 tonnes of ore per day. Current reserves are estimated at 36.2 million tonnes averaging 1.74 C/t Au and 2.21 g/t Ag. Alluvial gold in the gullies surrounding the deposit was first discovered in the 1880's and between 1907 and 1948 small scale open cut and underground mining was undertaken. Advances in extractive metallurgy and an increase in the gold price were major factors influencing the recent exploration and development of large scale mining of the deposit by Placer Pacific and Kidston Gold Mines. The breccia pipe is trapezoid in shape with surface dimensions of 1100 m by 900 m. Clasts show only limited evidence of mixing during brecciation, with the pre-breccia stratigraphy still discernible on the basis of clast types. This lack of mixing together with the intimate association with intrusive activity, suggests that the brecia formed by collapse, probably associated with the escape of a large volume of irothermal fluid from a crystallising hatholith. Mineralisation and alteration are also sratially and temporally associated with rhyolite emplacement and brecciation. Pre-breccia mineralisation consists of laminated stockwork quartz veins associated with muscovite, quartz and orthoclase-epidote alteration. Stockwork veins contain either anomalous molybdenite or gold. Uneconomic early stage post-breccia mineralisation and alteration consists of cavity infill quartz-epidote and calcite associated with potassic and propylitic alteration respectively. Economic late stage post-breccia cavity infill and sheeted veining consists of quartz-carbonate-sulphide infill associated with phyllic alteration. The grade of gold mineralisation generally decreases downwards in the system with an increase in the amount of pyrrhotite relative to pyrite. Pre-breccia stockwork quartz veins mineralisation is genetically related to the

Jan 1, 1987

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

By Kirkhouse C. B

Soon after the Broken Hill Limited started operations at their Iron and Steel Works at Newcastle, NSW, it was found necessary to install a mill for rolling small merchant bars, rounds, etc.An arrangement of the first mill laid down is shown on Plate 1., Fig. 1. This mill commenced operations on the 18th July, 1917.The feed for this mill was rolled in the existing 18-in. mill and sheared to the lengths required before being delivered to the billet storage yard. The billet storage yard is 90 ft. span, and is served by one 10-ton electric overhead travelling crane. Billets were placed on the billet bed preparatory to being charged into the heating furnace.The heating furnace was of the continuous recuperative with end discharge and had a hearth 40 ft. long by 10 ft. wide. The billets were pushed through the furnace by means of two hydraulic rams, which could either act together and push one row of billets, or act singly and push two rows of billets. This furnace was fired by producer gas from the producers shown on Plate I., Fig. l.The gas was conveyed to the furnace by means of a brick underground flue.

Jan 1, 1935

MR. L. C. BALL, chief government geologist, Queensland, wrote: This paper is intended as a severely mechanical exposition of the means adopted to deal with tremendous inflows of water concurrently with development and exploitation; but incidentally it serves as a splendid exposition of close co-operation maintained between the geological and engineering branches of this large organization.I have been impressed by the completeness of the mine plans of 'Mount Isa Mines Ltd.; but only such a paper as this has brought fully to my understanding the difficulty and complexity of the solid geometry involved in the detection and plotting of the orebodies and their stratigraphic control, including faults and large-scale brecciations, and the managerial foresight that set going the initial investigations.The company's geological branch of course must be given full credit for the results attained, but it gives me pleasure that the Geological Survey of Queensland has been closely associated in much of the study.It is noted that complete drainage was affected, but it would be interesting to learn whether the brecciated zone will again become waterlogged and whether from above or from below, and whether there has been any change in the dissolved mineral content of the water as the work progressed.

Jan 1, 1939

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By W Stange

Assessing the risks in a mining project is a key aspect of project evaluation. This is an exacting and demanding task because of the complexity due to the need to deal with uncertainty over long time periods. The way risks are assessed and managed is critical to the long-term success of the projects and the business. Discounted cash flow (DCF) analysis is commonly used for project and risk evaluation. A discount rate is selected that accounts for uncertainties in the cash flows. However, it is difficult to determine an appropriate discount rate due to the large number of factors that need to be considered and the complex relationships between risk sources. Using a proven framework, ævalue at riskÆ (VaR), this paper proposes to rigorously model and quantify ærisk at sourceÆ. The approach was first employed to assess financial market risks and is now widely used in the banking sector for risk assessment. In project evaluation, all risk sources are identified and estimated separately to ensure the overall project risk is quantified accurately. A bottom-up approach has been proposed. Estimates are first carried out for risk factors at the bottom of the project structure. The assessment is then applied at increasingly higher levels until the overall project risk is estimated. Value at risk is a versatile methodology and can be used in a local or integrated manner. The final value is objective and the calculation steps can be easily justified and followed. Four case studies have been included to illustrate how the proposed approach can assist management in decision-making.

Jan 1, 2009

By H Kim, M J. Sun

Global steel companies are actively combating climate change by reducing carbon emissions. Traditional steel production, using the blast furnace (BF) – basic oxygen furnace (BOF) process, heavily depends on coal and emits substantial CO2. To mitigate this, companies are transitioning to the more eco-friendly DRP (direct reduction plant) – EAF (electric arc furnace) process, which lowers CO2 emissions. This study quantitatively evaluates the impact of increased hydrogen consumption on the carbon footprint of product (CFP) through an analysis of direct reduction process heat and mass balances. The study prioritises a comprehensive material balance based on mass conservation principles. The heat balance is calculated using differences in enthalpy through state energy properties, avoiding heat consumption. Validation using operational data from Hyundai Steel Dangjin works’ blast furnaces shows close alignment between calculated results and actual data, with less than 1 per cent error. This methodology facilitates a detailed analysis of the direct reduction process, offering insights into its feasibility and efficiency. Analysis of the operational impact by increasing the hydrogen ratio demonstrates reduced CO2 emissions and increased heat requirements due to the endothermic nature of hydrogen reduction, in contrast to the exothermic CO reduction. Possible solutions include raising reducing gas temperature or enhancing flow rate. The study effectively utilises designed heat and mass balances to assess material quantities and thermal balance under different operational conditions. It lays the foundation for the initial direct reduction process design, aiding in deriving and optimising operational parameters. Additionally, it provides valuable insights into the challenges of increased hydrogen, contributing to the production of greener steel by addressing these issues.

Aug 21, 2024

By F Anthes, U Barow

Two tunnels are being bored using a æHydroshieldÆ in section 3.1 of the extension of the Underground railway line 5. At the end of the two tunnels, directly in front of the Hotel Adlon, the shields cannot be retrieved. The steel shell of the shield will be left in place within a sealed concrete block and the reusable components taken out through the completed tunnel. For the first time in Germany, an Underground tunnel is being lined solely by means of UNI rings. BerlinÆs Underground network is 165 km long and has 167 stations. Some 450 million passengers are transported annually. On account of the urban planning modifications that followed reunification, the network has to be adjusted, particularly in the city centre. The most significant project is the extension of the U5 from Alexanderplatz to the Lehrter Bahnhof. After completion, the U5 will be a continuous east-west traffic artery. It will provide a direct link with the new parliamentary and government district, open up new business districts and the cultural centre of the city.

Jan 1, 1999

By D Macklin, R Hammond, T G. Blenkinsop

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Base metal sulfides at the Currawong volcanic-hosted massive sulfide deposit in the Lachlan fold belt of Victoria, south-east Australia, were formed in the late Silurian, but D2 deformation of the deposit in the Devonian Bindian orogeny was responsible for structural repetition that created the resource. The primary sulfide lenses were stacked by reverse-sense shear zones within a volcano-sedimentary sequence dominated by dacitic intrusions and turbidites. Shear zones were localised along lithological contacts, including the margins of the sulfide lenses. The competent dacitic intrusions did not fold during D2; folding was restricted to the packages of metasedimentary rocks. Overturning occurs within, but not between, the metasedimentary packages. The overall geometry of the deposit is that of a duplex, but the detailed shape does not conform to idealised duplex types, probably because of post-D2 deformation. A significant complicating factor for understanding the deposit, and for resource evaluation, is the dramatic variation in deposit geometry along strike, which may also be due to post-D2 deformation. The present day configuration of the deposit results from constructive thrust repetition of what may have been a single ore lens and destructive along-strike disruption controlled by rheology.CITATION:Blenkinsop, T G, Macklin, D and Hammond, R, 2015. Rheological controls on the geometry of the Currawong volcanic-hosted massive sulfide deposit, Lachlan fold belt, Victoria, south-east Australia, in Proceedings PACRIM 2015 Congress, pp 469–474 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Ertsberg (Gunung Bijih) Mining District is located in the core of the highlands of west New Guinea, an island long recognised as the product of a Cenozoic arccontinent collision. Geologic studies in the Central Ranges of the Papua Province of Indonesia (near Puncak Jaya, 4884 m) have revealed timing relationships, when combined with mechanical considerations, led to a refined model for the tectonomagmatic effects of collisional orogenesis and the formation of the spectacular Grasberg porphyry-type copper-gold (Cu-Au) deposit.   An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

In classical drill and blast underground mining methods, especially narrow vein operations economic quantities of broken ore can be left behind following normal mucking operations on the stope floors. The ore left behind can have significant economic value and if not collected can be lost forever. This paper reviews techniques for cleaning this material from stopes that have been used in the past and reviews possible modern techniques that can be applied to ensure this valuable material is removed from the stopes.

Aug 1, 2010

By P Holt, M Allen

On the first of July, 2012, the Australian GovernmentÆs Clean Energy Act commenced. From this point, a price of $23/t of CO2-e will apply to facilities that trip the liability threshold. This first part of this paper concentrates on the mechanics of the Clean Energy Future legislation and how it will be applied to the mining and mineral processing industry.The second part of this paper contains analysis of the data presented for typical mine operations. Methodologies for constructing a carbon strategy are also presented. This will entail determining what the objectives of the carbon strategy are, and defining what the strategic priorities for a business should be. An action plan to address the risks identified from the Clean Energy Act is also developed as part of the strategy.Details such as the advantages and disadvantages of opting into the carbon price scheme for liquid fuels are shown. Other considerations such as the ability to acquire permits through the carbon farming initiative or through overseas clean development mechanism projects are explained.CITATION:Allen, M and Holt, P, 2012. Implications of the carbon price and developing a carbon strategy, in Proceedings International Mine Management 2012, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By M Gabbitus, B Young, T Lukins, M Slater

This paper details the implementation of a new type of grade control system at the Black Star open cut mine in Mount Isa, Queensland. It explores the site requirements for grade control, what as previously in place and what the site required moving forward. It also details some of the features of the system installed and why it was chosen over other grade control systems available. Black Star open cut mine has been in operation since late 2004, and was developed to extract the surface extents of the Ag-Pb-Zn mineralisation previously mined in the Isa Lead Mine. Black Star is currently mining seven distinct orebodies in and around active void hazard zones and hence, its grade control requirements are very detailed and complex. The implementation of a new system to manage the model update and block out processes was, therefore, of critical importance to the site and required a detailed understanding of the requirements of the entire mining team from drilling through to geology, survey and production. Having previously run the grade control process using site specific æblack boxÆ scripts and macros, Black Star needed to implement a more open, auditable and flexible system, which allowed the geologists to control the process and make strategic changes as the situation demanded. MineSightÆs Axis Grade Control, with its flexible, generic framework for managing the process, met these demands. Being an out of the box solution that requires minimal setup and training was also a key factor in the decision to use it.CITATION:Lukins, T, Slater, M, Gabbitus, M and Young, B, 2012. The introduction of axis at Black Star Open Cut, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 71-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By Denholm WT

The main objective of the experimental study was to investigate the dissolution kinetics of various forms of carbon under iron bath converting or smelting-reduction conditions, i.e., particulate, free moving carbon in contact with a turbulent iron melt. Iron/carbon melts were contained in cast magnesia-lined silicon carbide crucibles heated by a medium frequency induction furnace. The melts were stirred by injecting nitrogen through 2 mm I.D. alumina lances submerged to a depth of 50 mm in the 100 mm deep baths. Particulate carbon in the form of graphite, brown coal char and petroleum coke, were dropped directly onto the turbulent bath. The dissolution rates of the various carbon types were monitored by taking periodic bath samples for subsequent carbon analyses. The effect of carbon particle size (1-6.25 mm), the degree of bath turbulence (nitrogen stirring rates of 0-20 litres/min), and bath temperature (1300-1500¦C) were assessed. The analysis of the results was complicated by particle buoyancy effects, but it was established that the dissolution rates of the three carbon types investigated were similar, and increased linearly with increases in the gas stirring power inputs. Particle size had relatively little effect on the dissolution rates.

Jan 1, 1984

By Torrance AC

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation veloci- ties of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation meas- urement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 150g. owever, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1988