Search Documents

At 11 p.m. on Tuesday, 24th July 1979, an explosion of methane gas in a three heading development panel at Appin Colliery resulted in the deaths of fourteen men. The explosion followed after or was asso- ciated with a changeover of the ventilation to achieve a central intake between two returns. Investigation by Inspectors was followed by separate Judicial and Coronial Inquiries. Investigational information aimed at understanding the circumstances of the ex- plosion was prepared for the Inquiries. Recommendations following the Judicial Inquiry have been adopted by the Department of Mineral Resources.

Jan 1, 1981

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

By R Steven

"Surveying, and as a result, surveyors, have been around since the start of time, and it has been said that so has their methodology!The theodolite and tape have been the backbone of a time-tested practice that has led to ground breaking advancements such as electronic distance measurement (EDM), global positioning system (GPS) and positional laser scanning. However, it was the introduction of the unmanned aerial system (UAS) that has allowed mine sites such as St Ives to take the next step towards truly turning survey data into metadata.This paper will explain how the unmanned aerial vehicle (UAV) was adapted to meet the requirements of a mine site supporting a major open pit operation, and how the open pit mining team adjusted their planning and production processes to maximise use of the extra data and information available to them.The advantages of the system include point cloud surveys with corresponding large-scale up-to-date photography and computer generated high detail contouring of mined areas that are then incorporated into the mine plan. All the while, the use of the UAV must be tailored to each specific problem encountered and a solution then matched.Citation:Steven, R, 2016. Trials, Tribulations and Triumphs of Unmanned Aerial Vehicle Surveying at St Ives Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The creation of an accurate and precise enough database requires the collection of many representative samples, subsampling and assaying them without destroying their integrity. The selection and implementation of sampling protocols often lead to severe difficulties, making the unaware practitioner vulnerable to massive exploration, feasibility and operating failures. Therefore, there is no substitute for a good understanding of the Theory of Sampling (TOS). Either because of ignorance, or because of short-term economic reasons, failure to comply with many stringent conditions can be devastating for the validity of a feasibility study, leading to false evaluations, to the abandonment of a viable property, or to the exploitation of one that is not profitable. All these failures have something in common: insufficient duplicate sampling, subsampling and assaying were performed; very important, preliminary heterogeneity tests were never performed; for short-term economic reasons, poor sampling and subsampling protocols were selected, second-class sampling systems and weightometers were installed and poor preventive maintenance and cleaning were implemented;and sampling experts were called only when the project was obviously in trouble. The conclusion is clear: in due time, iterative auditing of sampling practices is an insurance policy against massive financial losses for the company involved. A complete, comprehensive 100 point checklist of sampling Quality Assurance and Quality Control is provided, so critically important details to ensure success are not forgotten.

Mar 1, 2010

By S Versace, D Arnott, D Bojcevs, A Shaw

The George Fisher deposit is a significant sediment hosted silver-leadzinc resource located 2 km north of the Hilton Mine in NW Queensland. The George Fisher feasibility project involved the completion of underground and surface drilling programs to delineate Measured and Indicated Resource which could be converted to an Ore Reserve through mining and commercial studies. The geological information which was collected and used for the feasibility study included a major program of diamond drilling, predominantly from underground sites, but with some drilling also completed from surface. All drillcore was geologically and geotechnically logged, sampled and assayed. Data was also collected from underground cross-cut and drive development which was mapped for rocktype, ore distribution, structure and geotechnical condition. This new geological data, generated during the Pre-Feasibility and Feasibility stages, was combined with results of all previous drilling campaigns in the George Fisher area to produce a comprehensive database on which geological modelling and Resource estimation could be based. To allow fast and accurate collection and utilisation of data from the drilling program, digital collection processes were used where possible. This resulted in rapid data entry into the project database, significantly enhanced data quality, 100 per cent data ownership within the project team and increased productivity levels. Processes used during the project data collection program are described, lessons learned are related and suggestions for ænext timeÆ are listed using the benefit of hindsight.

Jan 1, 1998

The mining industry has expanded significantly in the Pacific Region over the past two decades through a mix of new developments and brownfields expansions of existing operations. Despite this overall success there are also a number of well publicised examples of less than successful minerals ventures. These problem developments highlight the fact that success cannot be taken for granted and that rigorous planning and attention to detail is essential. The dominant growth has come through expansion of existing businesses, notably alumina, iron ore and coal, achieved through both efficiency gains on existing plant and step change capacity additions such as new mines and/or expanded processing plant. This expansion has largely been linked to increased market opportunities. The major issues are the quality and extent of the host resource, achieving the market targets, and the efficiency of the expansion effort. There can be also a range of site specific issues which need to be addressed. The development of new greenfields operations is often more complex as it can bring a wide range of new issues. Depending on the nature of the development, and the companies involved, these can extend from initial financing through to obtaining a market position. Incorporating major new technology and/or establishing infrastructure and attracting staff to remote locations can also add significant challenges. This paper outlines many of the critical factors which need to be considered prior to proceeding with major expansions or greenfields developments. These will be linked to a number of developments in the region over the past decade.

Jan 1, 2004

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By P Holtham, R Dunne, D Stoll

Flash flotation is a process designed to remove coarse, liberated, fast floating minerals from hydrocyclone underflow. Irrespective of liberation, coarse particles would normally remain in a grinding circuit until they are reground fine enough to report to the hydrocyclone overflow. Additionally, minerals of high density also report to hydrocyclone underflow despite being fine in size and/or liberated because hydrocyclones separate on the characteristics of both particle size and density. Dense particles continually reporting to the hydrocyclone underflow can lead to over-grinding and the production of ultra fine particles. These particles exhibit slow flotation kinetics and thus are difficult to float in conventional flotation circuits. Therefore, removing coarse, liberated particles from the hydrocylcone underflow by flash flotation has the potential to improve recovery and can improve dewatering unit operations and reduce grinding costs.The impact on the overall performance of the flotation circuit by removing coarse, fast floating minerals prior to conventional flotation is not well understood. Ultimately, predicting the overall recovery improvement provides the justification for the installation of a flash flotation cell within the milling circuit. This paper will describe attempts to estimate flash flotation recovery improvements to the overall circuit using kinetic data from simplified batch cell flotation tests combined with limn-based modelling techniques.CITATION:Stoll, D, Dunne, R and Holtham, P, 2012. Modelling the impact of flash flotation from batch cell flotation tests using limn, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Major underground gold mine developments are not common in Australia especially when they are totally owned and hence financed by a relatively small public company. Ballarat Goldfields Limited with its Ballarat East Project is such a company. Financing a $20m underground exploratory access programme in a poor economic climate places added importance on the quality of the project. Critical factors such as ore reserves, environment, planning and the development program are of immense importance in devising and implementing a workable finance package that satisfies both the shareholder and the project's needs.

Jan 1, 1990

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

By B Taylor, S Evans

Bulk explosive technology for underground mining has not seen any significant technological advances since the widespread transition from ammonium nitrate fuel oil (ANFO) to ammonium nitrate emulsions (ANE) commencing in the 1980s. The in-hole energy profile that conventional ANE systems deliver is limited by the physics of chemical gassing and simple control systems. This compromises the range, precision, and accuracy of energy delivery into the blasthole, and in some cases limits the length of charge that can be delivered. Orica’s 4D™ bulk system removes many of these constraints, enabling better blasting performance across all underground mining methods. This paper reviews work completed at three mining operations across Australia, the United States, and Chile with a focus on how this system can improve mining operations and deliver sustained commercial and productivity benefits into the future. These benefits include improved ore recovery, reduced dilution from waste rock, and reduced overall explosives consumption. This paper also reviews how this new technology can be applied for planning future mining operations.

Sep 1, 2024

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

By D Mather

The Resources Boom of the 1960s in Australia provided a strong foundation for AustraliaÆs economic prosperity for the remainder of the twentieth century. In combination with sound economic management, our world-class minerals and energy sector has played a key role in the nationÆs competitiveness, and it has been the major source of our exports since the early 1970s. Even with the emergence since 1990 of major mineral provinces in Latin America and elsewhere, Australia has increased its percentage of world production of several minerals. Between 1990 and 2002, our share of iron ore production rose from 13 per cent to 20 per cent, nickel mine production from eight per cent to 17 per cent, copper mine production from four per cent to seven per cent and zinc mine production from 13 per cent to 17 per cent. Whether this situation will continue during the coming decades motivates the discussion of this reflective paper. The approach is to consider fundamental supply-side and demand-side issues in arriving at a view about the state of the world, the world minerals sector and the Australian resources sector in the coming decades. The argument draws from the experiences of other mature mineral producing countries such as Canada and the United States. In such nations, efficient producers have often sustained competitiveness for extended periods, despite falling grades and other challenging operating conditions. Yet several forces are changing the economic geography of the minerals industry in significant ways. These include the re-emergence of major global mining corporations, the revision of mineral policy in over 100 nations since 1985, the mobility of technology and more efficient transport both for mineral productions and mining professionals. Given these trends the paper argues that the Australian mining industry must continue to change and evolve significantly in the foreseeable future. Its leaders will need to be even more internationally focused if it is to maintain its strong competitive position.

Jan 1, 2006

The accurate determination of trace level gold in ores, metallurgical samples and process solutions is required because of the value of gold, the efficiency of the cyanide leach process and because of the high gold recovery from these cyanide solutions. It is thus necessary to routinely analyse geological and metallurgical samples with gold concentrations of 3 g tonne (ug g- 1ppm) and process solutions with a gold concentration of 0.01 mgL 1 (ppm) preferably with sufficient accuracy to quote at least two significant figures. Several techniques have been reviewed for their suitability for the routine gold analysis of these samples which also contain signif- icant concentrations of other ions. The classic fire assay technique has achieved the respect and confidence of mining personnel because of the results achieved by very experienced assayers. Other extraction and concentration techniques have now been shown to be equally effective. The use of instrumental analytical techniques particularly atomic absorption spectrometry have shown that cheaper procedures, which are as reliable, are now available to gold producers for the routine analysis required to maintain an efficient gold recovery process.

Jan 1, 1982

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987

By Beer G

The recent re-emergence of an Integral Pressure Stripping system which operates with both cell and column in closed circuit at elevated temperature and pressure, requires no cyanide in the eluate solution and has greatly reduced carbon reactivation requirements in seen as a progressive step in this area. Several of these re-configured IPS systems have been placed in service in Australia and overseas in the last three years, with the first of the new generation units constructed and commissioned by Como Engineers Pty. Ltd. at Mt. Fisher in the East Murchison of W.A. in September 1987. This plant was relocated to a new ore body at Darlot W.A. in February 1989. Use is made of a data base of raw plant performance figures from both Mr. Fisher and Darlot and its performance compared with other operating plants. Initial commissioning difficulties of the Mt. Fisher prototype and dis- cussed together with the modifications and operational procedures required to overcome these problems. Stripping times of less than 6 hours at 145 degrees have been achieved with barren carbon values less than l O ppm from loaded carbon values above 3000 ppm and with cell pass efficiencies reaching 90 per cent.

Jan 1, 1991