Search Documents

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

By R O. Laidlaw, J L. Mauk

The Coeur d'Alene mining district in northern Idaho, USA is the second largest producer of silver in the world. Mesothermal silver-lead-zinc veins occur in the metasedimentary rocks of the Belt Supergroup with five main types of associated hydrothermal alteration: 1) feldspar destruction, 2) hydrothermal bleaching, 3) carbonatisation, 4) sulfidation, and 5) silicification. Hydrothermal bleaching is characterised by hematite destruction with associated siderite and quartz veins and veinlets, coarse euhedral pyrite and magnetite. Bleached zones envelop both mineralised and barren veins and extend for metres to tens of metres into the wall rocks. Carbonatisation consists of addition of siderite, which occurs as veins, veinlets, stockwork, irregular blebs or spots, and coarsely disseminated grains, depending on the relative distance from the main vein structure. Siderite envelops nearly all mineralised veins, relates to all other alteration types and extends from several metres to tens of metres into the wall rocks. Pyrite and galena alteration dominate sulfidation and are associated with some mineralised veins. Pyrite alteration strongly correlates with siderite alteration and exists in three main forms: a) very fine-grained pyrite flooding, which can extend for metres to tens of metres into wall rocks; b) coarse-grained, euhedral pyrite, which is sporadic and associated with the redox boundary in hydrothermally bleached zones; and c) small isolated zones (6 - 15 cm) of medium-grained, subhedral to euhedral pyrite associated with pervasive siderite alteration. Where present, disseminated galena extends for metres to tens of metres into the wall rocks. Silicification is characterised by veins, veinlets, stringers, irregular patches and variable hardness in siltites and commonly appears in association with hydrothermal bleaching and siderite alteration. Although related to mineralisation, silicification is sporadic and in most places a clear envelope around mineralised veins cannot be identified.

Jan 1, 2001

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

The mobility of radionuclides released into aquatic, terrestrial and subsurface environments by mining, industrial processes is an area that deserves significant scientific attention. The presence of microorganisms in these environments can influence the transport of radionuclides. Free-living microorganisms constitute mobile suspended particles that may have a radionuclide sorbing capacity higher than that of the environment. Radionuclide transport will then proceed faster with than without microorganisms. In contrast, if the majority of the microorganisms are growing in biofilms on surfaces, transport of radionuclides may be reduced. Microorganisms can directly sorb radionuclides either within the cell structure or on the cell wall. Radionuclides could also be sorbed by minerals precipitated by microorganisms. Microorganisms produce complexing agents that can influence radionuclide mobility. The involvement of microorganisms in biogeochemical processes is related to their ability to include various chemical elements and their combinations into biochemical redox reactions. Microorganisms can alter the extent of radionuclide oxidation that results in their deposition as a result of the formation of insoluble forms. Some studies have shown the bioremediative potential of stimulating reducing bacteria to use some of the soluble radionuclides as electron acceptors and thus precipitate them out of solution. The microbial involvement in providing a barrier for radioactive element migration (uranium, technetium) and the formation of ores (eg uranium) has been justified. The mediated impact of microbial activity on radionuclide migration occurs through its effect on the ambient geochemistry by geochemical speciation changes, pH changes and changes to the ambient redox potential. As the mobility of many radionuclides depends on the pH and redox potential of the environment, these microbially mediated geochemical changes can influence radionuclide migration through changes to both the dominant radionuclide species and mineral phases.

Jan 1, 2004

By V Louchnikov

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in situ stresses and associated seismicity with potential rock burst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in Australian underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanised installation of a chain-link mesh as trialled at Golden Grove, a base metals underground mine in Western Australia. A purpose-built mechanised roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilising the hydraulic circuit normally used for the feed arrangement.A number of operational benefits have been identified during the trial, the main two being:•improved safety of underground personnel due to the reduced amount of manual handling, and•increased productivity due to the decreased cycle time (the trial suggests a 40 - 50 per cent reduction in time over the weld mesh installation method).Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rock burst prone conditions, the operational upsides recognised during the trial imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support.

Mar 21, 2011

By W L. Daniels, C Stilson, C Zimmerman

Mineral sands mining for ilmenite, rutile and zircon has disturbed over 1000 ha of prime farmland in Virginia (USA) since 1997 and additional areas are likely to be disturbed in Virginia and North Carolina (USA) over the next 15 years. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc. and restoration protocols have continued to evolve in response to a variety of economic, technical and social issues. Early on, the return of these lands to agricultural row-crop production was complicated by vertical stratification of tails + slimes and lateral variability in soil physical conditions in the reclaimed pits and by limited topsoil return. Virginia Tech and Iluka have worked cooperatively with all stakeholders for over 20 years to review the pre-existing research base, conduct new and innovative site-specific research and thereby provide reasonable expectations of post-mining soil productivity levels. In 2004, Virginia Tech, Iluka Resources and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45 ha research demonstration farm where the long-term effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Row crop yields between 2005 and 2010 were significantly above county average yields (regulatory target level) and approximately 75 - 80 per cent of undisturbed adjacent prime farmlands. The state regulatory authority has recently relaxed its position on the necessity of topsoil return versus use of topsoil substitutes based on appropriate on-site research results and the ability of the reclaimed soils to meet comparative local county crop yield targets. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry. CITATION:Daniels, W L, Stilson, C and Zimmerman, C, 2012. Development of effective rehabilitation protocols for mineral sands mining in Virginia, USA, in Proceedings Life-of-Mine 2012 , pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C Garrido, J Barrera, H Alvarez, L Perez, S Ramirez

In recent years, there has had a greater recurrence of studies and projects that consider tailings filtration followed by dry stacking to reduce the consumption of fresh water, the space required for disposal, and, eventually, to reduce the costs of the project. In addition, this technique could be required to meet new environmental restrictions to extend the life-of-mine of existing plants or to enable the development of new projects, especially in areas of high social interest. This article is intended to describe the most relevant technical aspects of the design and implementation of an iron ore tailings filtering system and its final overland disposal as well as physical and metallurgical surveys, and laboratory and pilot testing. Furthermore, it is presented how these activities are inserted in the project development to rationalise the resources. The case under study considers an iron mineral wet magnetic concentration processing plant. The outcome tailings are dewatered by means of thickeners, where the overflow water is recycled back to the plant. The underflow slurry is pumped into intermediate storage tanks before proceeding with further dewatering and final disposal. The project consists of a tailings filtration plant, belt conveying systems, a temporary stockpiling system, trucking loading and transportation system, moisture-conditioning facilities (spreading and airing), and final disposal facilities (compacting). Due to the stickiness of the filtered tailings that governs the belt conveying system design, the operating moisture range must be established. Besides, proper technical aspects such as planning, executing, and analysing both the laboratory and the pilot testing data to validate process design parameters; selecting filters; defining spare filtering capacity; handling the out-of-range filtrated moisture; sizing the belt conveying system; configuring the equipment involved, must be considered.

Nov 8, 2021

By P Clark, P A. Kirsch, R Tapia Rivera

Community members’ sources of information about companies’ social investments are often influenced by the messages in a variety of communication channels, such as newspapers, television and social media. In this sea of communication channels, corporate communications may not always have the desired effect in influencing community perceptions. This paper explores the efficacy of communication between mining companies and communities in Chile through content analysis of corporate sustainability reports and newspaper reporting.Chilean media reporting between 2005 and 2013 is examined to identify community perceptions of corporate social investments made by mining companies. Content within the Chilean newspapers El Mercurio (national) and Soy Chile (regional) is contrasted with content from corporate sustainability reports published by The National Copper Corporation of Chile (Codelco) and Barrick Gold Corporation, Canada (Barrick) for the same period. The objective is to identify differences in the way that corporate social investments are reported by companies in sustainable development reporting and by media in newspapers.Overall, the study demonstrates that the media’s framing and reporting of corporate activities was more negative than positive. Moreover, media outlets tended to focus upon the ‘negative impacts’ or ‘damage’ to communities brought about by mining developments. Conversely, companies’ public communications were largely focused upon direct improvements in livelihoods (health, education, etc) of neighbouring communities. This preliminary study provides a baseline for the development of new formats of effective communication with neighbouring communities. The paper advocates for an increase in participatory mechanisms with affected parties, which could lead towards a greater mutual understanding of the impacts and draw parties closer together.CITATION:Tapia Rivera, R, Kirsch, P A and Clark, P, 2014. Challenging Perceptions? Sustainability Reporting, the Media and Mining, in Proceedings Life-of-Mine 2014 , pp 413–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D David

The development of Western Australian magnetite deposits has lead to the design of some of the largest grinding mills and plants in the world. One of the projects demonstrates the efficiency gains possible by developing a simple yet thorough test program for circuit design. By drawing on the experience of current magnetite operations in Australia and the Mesabi and Marquette iron ranges in the United States, a basic flowsheet was developed. Through comprehensive testwork with AG, ball and stirred milling the flowsheet was optimized to take full advantage of each grinding mill’s strengths to reach the required final grind size. Laboratory work was verified in the pilot plant to optimize the energy efficiency of each grinding step while ensuring adequate liberation at each step for sufficient gangue rejection. By using three stages of grinding, the ball mill can best be employed in ensuring all top size gangue material is liberated and removed in the second magnetic separation step. The inclusion of the IsaMill, with its inherent steep product size distribution, as the tertiary grinding stage ensured that maximum grade was achieved and simplified the downstream process while giving further improvements in total grinding capital and operating costs. In this way the combination of the two technologies downstream from the AG mill is far more efficient than either would be on its own by reducing the total installed power by 1/3 and annual grinding media cost by 2/3.

Aug 8, 2011

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Misra, R Ganguli, S Bandopadhyay

The objective of this paper is to assess the accuracy and applicability of recent state-of-art methods such as the machine learning algorithms (MLA) for mineral resource estimation. Conventional methods such as geostatistics have been predominantly used in the mining industry for this purpose with varying success. Recent advances in the use of MLA have provided a fresh approach to obtain improved accuracy in the estimation of mineral resources. Two MLA methods: the neural network (NN) and the support vector machine (SVM) have been used to estimate a polymetallic ore deposit in Alaska.The general characteristic of SVM and NN emphasises the fact that they can approximate any multivariate non-linear relation among variables. Although neural network models are able to capture the nonlinear spatial relationships that may be present in the data, they are usually difficult to optimise under sparse data settings. Of the various NN alternatives, despite their effectiveness, the model selection and estimation process is typically difficult as it involves solving complex integration and optimisation of parameters. In support vector modelling (SVM), estimating of parameters involves optimisation of a convex cost function. The working principle of SVM makes it robust against noisy and extreme value data. At the same time, it can capture the spatial distribution of ore grade more effectively with careful modelling and selection of SVM parameters.The outcome of the MLA methods were compared to those of the geostatistical ordinary kriging (OK) application to study their generalisation ability. The comparison was made using the following goodness of fit criteria: mean-squared error; mean absolute error; mean error; and coefficient of determination. The results indicated that the MLA methods may improve the predictability of ore deposits and thereby reduce the inherent risk in mineral resource estimation.

Sep 26, 2011

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By H Mischo, G Barakos, J Gutzmer

The continuously growing demand for rare earth elements (REEs), in combination with the crisis of 2009 and the price spike of 2011, has initiated a treasure hunt for rare earth deposits all over the world in recent years. Since then, commodity prices have declined and are now quite stable, yet the world is still dependent on China’s dominance of the market and its export policies. Exploration is unremitting and numerous resources of potential interest have already been revealed in many countries; however, proceeding to mining operations is not that simple, especially when it comes to the exploitation of rare earth deposits. Evaluating the feasibility of a mining project is always a unique, sensitive and rather complex process that depends on multiple criteria.This paper focuses on clarifying the present and future global situation in the development of respective deposits and on identifying rare earth-specific criteria that influence the overall feasibility assessments of any potential (especially underground) mining projects. Environmental impacts, legislation issues and the presence of radioactive pollutants are some of the notable boundary conditions that govern rare earth mining operations and need to be taken into consideration. Furthermore, the balance problem between the supply and demand of the different REEs can determine decisively whether a deposit of specific REEs is economically exploitable. For this reason, evaluations are made regarding the future strategies to be enacted in order for the rest of the world to detach itself from this situation. The ultimate goal of these evaluations is for them to be incorporated in an overall assessment tool for rare earth underground mining procedures that will be implemented in real case studies to determine their sustainability.CITATION:Barakos, G, Mischo, H and Gutzmer, J, 2015. Status quo and future evaluations of global rare earth mining (with respect to special rare earth element-industry criteria), in Proceedings Third International Future Mining Conference, pp 21–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

The first stage in the refining of lead blast furnace bullion is the removal of copper and is normally done as a batch process in open kettles.A number of attempts have been made to establish continuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) at Port Pirie have overcome this problem by constructing a reverberatory furnace and ancillary cooling system of a novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.INTRODUCTIONLead bullion emerging from the blast furnaces at Port Pirie is at a temperature of about 1100°C and contains, among other impurities, about 1 per cent of copper.The first stage of refining is the removal of this copper by a drossing operation and in the past this was done, batchwise, by allowing the bullion to cool back in 100 ton kettles.At about 700°C, copper dross begins to separate as a crust on the surface of the kettle and this separation was allowed to continue down to about 450°C when the crust was brokenup and skimmed manually using a long handled, balanced, spoon. The dross was then smelted in a reverberatory furnace to produce a saleable copper matte and separate out lead bullion, which was returned to the drossing kettles. The copper content of the drossed bullion was then further reduced by a sulphur treatment process.The drossing operations involved hard manual labour under arduous conditions and the pouring of hot bullion into...

Jan 1, 1963

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

Basic Oxygen Steelmaking (B.O.S.) commenced in Australia in December, 1962. Two 200-ton furnaces were installed initially at Newcastle with a 50-ton furnace coupled to a continuous casting machine added in 1967. In 1965, two 100-ton furnaces were installed at Whyalla plant and two 225-ton furnaces are nearing com- pletion at Port Kembla to commence oper- ations in 1972. Plant layouts in each centre differ due to changing circumstance and increasing knowledge of the B.O.S. process since 1962. Raw materials are a most important factor for good operation of the process. Most materials come from within Australia but some are imported. General operating practices are similar in each plant, although treatment of fume at Port Kembla will be by the OG (Oxygen Converter Gas Recovery) Process as against electrostatic precipitators in Newcastle and Whyalla. Special alloy steels as well as plain carbon steels can be made by the B.O.S. process. Production potential of the process in Australia has yet to be fully utilised with 45 per cent of steel production coming from B.O.S. In 1971.

Jan 1, 1972