Search Documents

By M Fahey, A B. Fourie

Over the past ten years, the mining industry has witnessed the introduction of a new and innovative mine filling technique known as paste fill, which consists of placing full stream tailings with small amounts of binder and water into underground stopes. Paste fill has benefits over traditional backfill methods, such as higher solids contents than hydraulic fill and easier transportation than rock fill. From a geotechnical perspective, the behaviour of very fine material in a fully saturated state can be complex, particularly when binder is added. Previously, there has been no rigorous solution to understanding the paste fill deposition process, resulting in uncertainty regarding critical aspects such as barricade load calculations. This uncertainty has the obvious consequences of potential barricade failures (including at least 12 over the past four years), and for many operations attempts to deal with this uncertainty has led to excessively conservative filling schedules, restricting production. This paper presents an application of Minefill-2D, the first rigorous model capable of representing the paste fill deposition process. The model couples the processes of material accretion, consolidation and cement hydration to calculate the distribution of stress around a stope (including the total stress applied to barricade structures) during filling. Minefill-2D is a finite element numerical program, which has been verified using laboratory element tests, centrifuge tests and in situ measurements (Helinski, 2008). The authors present a sensitivity analysis, carried out using the model, to demonstrate some of the critical and less critical aspects relating to paste backfill deposition. The results of this sensitivity analysis are used to devise a fill management strategy that can be utilised to minimise the risk of barricade failures and maximise fill rates where appropriate.

Jan 1, 2008

By Palmer DJ

Mercury is introduced into EZ's electroly tic zinc/sulphuric acid plant complex at Risdon, Tasmania, in zinc sulphide concentrate. Mercury is volatilised during the roasting operation and then distributed in the sulphuric acid plant effluents and product acid. Following an investigation of the factors determining the mercury distribution, a plan was formulated to-provide an environmentally accep- table degree of mercury containment at Risdon. This paper discusses details of the various control measures investigated and out- lines the reasons for selecting the particular procedures finally adopted for the Risdon plant.

Jan 1, 1980

By Shillabeer J

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

By R M. Yanamandra, S K. Tripathy, N Mangadoddy, P Sudikondala, P Ankireddy

Spiral concentrator is one of the most commonly used gravity concentration devices in mineral processing. The particles are classified based on their specific gravity and size. The present work analyses the experimental and numerical investigations of the water flow field, such as fluid depth and free surface primary velocity of two high gravity spiral concentrators at different flow rates. The measurement techniques use a flow depth gauge and flow visualisation technique adapting lycopodium powder as the tracer. Flow features in terms of liquid depth and primary velocity at the free surface of the flow are captured across the trough in two different high gravity spirals. A highspeed motion camera with an imaging frequency of 5400 frames per second and 768 × 768 pixel resolution is utilised to track the tracer particles in the liquid flow on the dark surface background. Further, the two-phase flow is studied numerically on high gravity spirals based on the volume of fluid (VOF) approach utilising the RNG k-ε model and Reynolds Stress Model (RSM) for predicting the fluid flow on trough surfaces such as water depth and free surface primary velocity. The CFD predictions of the flow field for the two spirals are attempted to validate against experimental data. The high gravity spiral concentrators show lower flow depths and free surface primary velocities but steep velocities on the outer trough zone compared to that of low gravity spiral concentrators (conventional coal spirals). Among the computationally tested high gravity spirals, higher pitch and higher secondary slope design shows greater flow characteristics.

Aug 24, 2022

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By M Hassall, E Humphries

Personal risk assessment processes, also known as Take 5 or SLAM (Stop, Look, Assess, Manage) have been utilised in high hazard industries for over 30 years. However, there is limited research to understand if a personal risk assessment process improves safety and health outcomes. The author’s learnings during discussions with training participants in G3/G-MIRM (Risk Management Systems) and G2 (Risk Assessment for Supervisors) courses have provided them with significant insight into understanding if a personal risk assessment process is valued across a number of mining industry organisations. These discussions arise when the four-layer model is presented (Figure 1) where ‘Layer 4’ represents the last resort risk checking activity. In this context, training participants agree that this process has value. However, the consistent opinion is that the personal risk assessment process is not effective, that it is a ‘tick and flick exercise’ and is not achieving the desired outcomes.

Apr 16, 2024

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

By J Lyons, M Hasan, D Pepper, C Vadeikis

Processing of large volumes of ultrafine ores has long challenged mineral processing operators because of lower recoveries and increased tailings. This has led to many deposits, or parts of existing deposits, being viewed as uneconomic. As the mining industry can no longer afford to overlook resources that require finer sizes to achieve liberation or result in high tailings losses, the need for technologies to address these issues has increased. Mineral Technologies (MT) worked with a prominent Australian iron ore producer over five years to implement an innovative gravity separation technology for the beneficiation of ultrafine magnetite. The magnetite mineralisation requires a liberation size of <40 μm and selective rejection of ultrafine silica prior to magnetic separation. Through collaboration with the client, MT applied their Lyons Feed Control Unit (LFCU) technology for the beneficiation of finely grained magnetite. LFCUs are widely used in the mineral sands and iron ore gravity plants, and in tailings applications, to recover water and provide constant high density process streams. This project was an extension of knowledge gained from these applications. Test work was conducted on-site, using 1 t/h pilot and 300 kg/hr laboratory scale units. This test work showed that the LFCUs could reject 20 per cent of feed mass to tails whilst recovering >94 per cent of Fe to product. This upgraded the feed from 53.7 per cent Fe and 19.7 per cent SiO2 to 63.8 per cent Fe and 8.8 per cent SiO2. Recovery by size data showed a minimum 88 per cent Fe recovery to product for <8 μm material and up to 98 per cent Fe recovery for the -38+25 μm fraction. The LFCU rejected 70 per cent of <25 μm SiO2. The information obtained from the test work was utilised in the design of the full-scale units which are due for installation at the project site in 2021. This paper outlines the results of this laboratory and pilot scale test work and how the data obtained was used to design the full-sized units.

Nov 8, 2021

By J Pan, G Qiu

In this paper, an analysis is made of the present situation in the Chinese steel industry and its demand for iron ores. It is shown that the demand for iron ores has been growing substantially with the rapid development of the steel industry all over the world, especially in China. However, the iron ore market is currently in the situation where supply exceeds demand due to the economic crisis, with more investment in mines and less output of steel for several years ahead all over the world. Gigantic pressure is confronting the Chinese steel mills due to the too high and irrational price of iron ores. It is time to return the price of iron ores to a normal position much closer to their value. More attention has therefore been paid to developing low-grade and complex iron ore resources in China due to the irrational price of imported iron ores. More innovative mineral processing processes have been developed to tackle these complex resources. A systematic introduction to the development of beneficiation processes for low-grade iron ores is provided, including upgrading low-grade siderite, limonite, micron sized haematite and magnetite resources.

Jan 1, 2009

Stilfontein Gold Mine, located approximately 160 km west of Johannesburg, produced both gold and uranium from 1952 through to the early 1990s. On decommissioning the mine infrastructure, treatment plants, rock dumps and three tailings facilities were left to be rehabilitated at considerable cost to the mining company. The community that had grown up with the mine and had settled in the mine village were faced with deteriorating socio- economic conditions. &nbsp; Mine Waste Solutions (MWS), a company with a socio-economic Vision expressly created by DRD (Pty) Ltd and Fraser Alexander (Ltd) for the purpose, took over the mine surface infrastructure with the objective of closing it down in an economically sustainable manner by recovering materials, converting mine infrastructure to useful purposes and re-mining of the tailings to recover residual gold to finance the project. A business case was prepared and presented successfully to investors and bankers and the project was commenced in 2003. &nbsp; The paper covers the scope of the project and gives an account of the practical lessons that were learnt as the project developed over a period of five years. Key technical issues that are covered by the paper are the re-mining techniques that were deployed to clean up the old tailings dam footprints and the selection of the deposition site to minimise the incremental impact associated with the tailings and concurrent rehabilitation of the facility. In addition the paper will outline the positive benefits that were generated for the community and the improvement that was achieved in the physical environment. &nbsp; The paper illustrates clearly how a mine can be closed in a manner that produces benefits for the community, the environment and the investor.

Jun 1, 2010

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60&apos;s and 70&apos;s provide a basis for forecasting the changes that can be expected in the 1980&apos;s. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960&apos;S If you look at the truck development that occurred in the 1960&apos;s, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960&apos;s. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By Klenowski G, Gilmour G. A

The Metropolitan Water Supply, Sewerage and Drainage Board, Perth, has recently con- structed two major sewerage tunnels in the metropolitan area and a further one is under construction. These tunnels were constructed in sand, sandstone and limestone. The Tamala Limestone is a Pleistocene calcareous dune sand which now varies in com position from loose sand to cemented rock. Investigation techniques included surface mapping, auger and diamond core drilling, seismic refraction geophysics and mechanical testing. The variable nature of the ground caused difficulties in all aspects of the investigation, particularly in core recovery and seismic work. The Beenyup Tunnel, 2.25m in diameter and 3440m long was excavated with a Dosco TBM 1800 machine and shield with precast concrete Charcon Universal bolted segment lining. The Burns Beach Sewer Tunnel, 1.27m in diameter and 860m long was hand excavated with precast reinforced concrete lining pipes jacked continuously behind an excavation

Jan 1, 1981

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

THE paper is principally eoncerncd with experimental work carried out the author whilst a number of the metallurgical staff at the Cockle Creek works. The metallurgical has been discussed sufficiently for the reader to follow the course of the experiments but the actual plant has only been described in so far as it effected metallurgical treatment, since the arrangement of such a smelter is a matter of common knowledge.The lead-roasting plant consisted of Godfrey roaster, Dwight-Lloyd maehines and Huntingdon-Heberlein pots. The usual treatment was in the Godfrey furnaces, followed by sintering in the Huntingdon- Heberlein pots. The paper is divided into two parts in the Godfrey furnaces and Huntingdon-Heberlein pots. An account of experiments on the utilization of the hood gases from the Huntingdon-Heberlein pots for acid making...

Jan 1, 1924

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By O S. Maluleke

In some deposits valuable heavy mineral quality is poor due to increased mineral surface coatings from higher slimes and more competent sand orebodies. Mineral surface coating can include silica or aluminium rich clay minerals and iron based minerals that render the final product quality off-specification, in this case specifically ilmenite and zircon. Conventional physical beneficiation processes such as magnetic separation, electrostatic separation and gravity separation are not able to remove these surface coatings. Surface dependent separation techniques such as electrostatic separators are affected by these coatings which hinders the rejection of non-valuable mineral from product. Attrition scrubbing is the most commonly used technique to reduce surface coatings, using mechanically induced particle to particle interaction, abrasion and shearing.In many cases it is a challenge to measure the surface removal efficiency of these scrubbing units. Elemental analysis techniques (ie X-ray flourescence) (XRF) in a multi mineral environment are unable to measure surface impurity reduction with enough precision. Mineralogical analysis (in this case Qemscan®) has constraints in terms of sample preparation with highly coated particles being plucked out during block polishing. This paper suggests a combination of laboratory separation techniques coupled with elemental analysis to evaluate the surface removal efficiency. Three different types of feed materials were used to analyse the efficiency of surface removal using production attritioner scrubbers. This approach relates the downstream beneficiation plant’s expected performance with that of the attrition scrubber’s scrubbing efficiency.

Oct 5, 2011