Search Documents

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

By Glatthar J. W, Lauder D. W, Manlapig E. V, Mackinnon I. R

The Ok Tedi copper orebody consists of porphyry and skarn orebodies. The skarn orebodies, identified by different mineralogies, are the source of high intermittent fluorine levels in the mill concentrates. This paper discusses the results of t

Jan 1, 1998

By M Baker

Biodiversity offsets are conservation actions intended to compensate for the residual, unavoidable harm to biodiversity caused by development projects. The use of biodiversity offsets in the context of mining has significant potential for enabling mining to take place in areas with biodiversity values, where it would not otherwise be possible to meet the relevant legal tests under the Resource Management Act 1991, and potentially the Conservation Act 1987. This paper looks at the concept of biodiversity offsets (and environmental compensation generally) both in New Zealand and internationally, and considers how lessons learned overseas may be adapted for this country. In New Zealand the practice of biodiversity offsets and environmental compensation is ad hoc and variable. The challenge with biodiversity offsets is to establish a transparent and coherent means of identifying the overall priorities and objectives of adopting such an approach, as well as how the relevant values are measured and protected. Establishing a methodology for quantifying biodiversity value, and the need for clear policy guidelines on biodiversity offsets are identified as key areas in need of wider discussion.

Jan 1, 2007

By H Arvidson, A Walker, N Pollock

Following the recent tailings tragedy in Brumadinho, the Investor Mining and Tailings Safety Initiative was formed representing institutional investors in the mining industry. This Initiative, led by The Church of England (CoE), requested data from 726 mining companies on each of their Tailings Storage Facilities (TSFs). What this exercise confirmed was that there was no public database of TSFs, and that there was a clear gap in tailings management systems within the disclosing companies. We present an approach using technology to support best practice TSF management, governance and disclosure which was originally submitted as part of University of Cambridge Post-graduate studies in Sustainability Leadership in January 2020. The aim of the paper is to discuss how technology could be used to deliver a Tailings Management Solution (TMS) that is aligned with the Global Industry Standard on Tailings Management (GISTM), and supports rigorous governance leading to disclosure. Subsequently the goals of the plan are aligned with that of the co-conveners of the GISTM (the International Council on Mining and Metals (ICMM), Principles for Responsible Investment (PRI) and United Nations Environment Program (UNEP)) which is to facilitate operators’ trajectory towards zero harm to people and the environment. Most of the focus to date around tailings management post Brumadinho has been on monitoring technologies, of which there are many. It is obviously important to acknowledge the critical role of monitoring technologies; however, our approach is agnostic to monitoring technologies and assumes that all of them are relevant. Our focus is on the data management, reporting and governance leading to disclosure of the information. Critical components of developing the TMS include adapting existing software products and solutions, recognising a system thinking approach is needed, strategic partnerships to deliver an accessible solution faster and more cost effectively, and, new ways of collaborating. The TMS should also accommodate relevant regional geotechnical codes and standards. The industry need for a TMS is well established and urgent, with significant pressure from regulators and civil society for the industry to address this significant issue.

Jul 1, 2021

As a minerals company, obtaining the appropriate consents under the Resource Management Act 1991 and getting permits granted for exploring, prospecting and mining under the Crown Minerals Act 1991, is necessary for actively exploring and mining in New Zealand. But the essential mix of ingredients for a viable and healthy Industry go way beyond this.   In the short term, an individual company seeking to operate on or within the Crown minerals estate of New Zealand must chart a course through the requirements raised by new cornerstone legislation, the Resource Management Act, the Crown Minerals Act and, the Conservation Act 1978 (where the minerals sought coincide with this estate).   However, this paper suggests that in the longer term for individual operators within the Industry and for the Industry at large to remain viable and sustainable and for New Zealanders to continue to enjoy its benefits, much more is required. Not least of which is a better balancing of competing uses and attitudes, which will require an opening of minds, a change in mindset, topped off with those two most essential of ingredients advocacy and leadership.   New Zealand has undergone massive restructuring in the last 15 years. Is it complete? Have each of its fronts evolved to the end point which was envisaged by the designers of the regime? What are the advantages? What is left to be done? What are the impediments from an incomplete transition which are left to either dog the Industry or remain as a challenge to be removed to ensure the Industry's smooth sailing into a prosperous and environmentally clean and friendly future? A future wherein an educated and understanding public welcome and are proud of the Minerals Industry to whom they owe the standard of living which they enjoy.   This presentation will examine the role of the New Zealand Minerals Industry Association (NZMIA) in paving the way for an optimum operating environment in which to couch a healthy industry into the future.

Jan 1, 1997

By A Kitchen

For the past decade, demand for Australian resources has reached unprecedented levels, thanks mainly to the emerging superpowers of China and India. Meeting demand has meant miners and governments alike have ploughed billions into capital expenditure projects for logistics infrastructure such as roads, rail and ports, to support the ever expanding number of mines and mineral volumes. In more recent times, however, the effect of the global economic crisis has led to a decline in demand for Australian minerals. The downturn has seen companies lay off workers in droves, and delay or cancel expansion projects, in an attempt to preserve cash flow. Whilst the current economic cycle has hit the mining sector hard, it is an opportunity for companies to take stock of their existing operations and plan for the future. As mining companies grapple for scarce capital resources, it is inevitable that industry consolidation will ensue. This presents challenges and opportunities for both buyers and sellers alike, looking to expand operations, or sell off assets to raise cash.

Jan 1, 2009

Forty two new apatite and zircon fission track analyses on the Kubor-Marum-Bena Bena area of northern Papua New Guinea severely constrain the timing of tectonic events and hence the tectonic models for New Guinea, particularly arc-continent collision. In addition, the data can be analysed regionally in terms of known and assumed lithospheric fault zones inferred to control mineralisation (eg. Corbett 1994; Kendrick et al 1995; Hill et al 1996) to determine reactivation of these zones. When combined with the new kinematic plate models for the evolution of New Guinea (Hall 1997) there is the potential to predict likely zones of mineralisation. The low-medium grade? Palaeozoic rocks of the Bena Bena terrane yielded a zircon fission track age of 17 Ma, indicating the time of cooling below 200¦C. The age is consistent with `the shift, at about 16-18 Ma, from volcanolithic sediments to mixed provenance sediments rich in quartz and metasedimentary lithic fragments in the southern Finisterre Ranges (Abbott et al. 1994). This shift was recorded in the Sukurum Formation, which ranges in age from Middle Miocene to Pliocene with quartzose and metasedimentary grains in all samples. Although recording rocks at temperatures of 200¦C and hence depths of ---5km, the 17 Ma age suggests the Bena Dena terrane was rapidly cooling at that time due to uplift and erosion, supplying metasediments to the southern flank of the Finisterre Range, currently 100 km to the east. Significantly, the Middle Miocene Akuna Intrusive Complex, dated 14-17 Ma by Page (1976), lies almost entirely within or adjacent to the Bena Bena terrane. Potentially the uplift, erosion and cooling of the terrane at 17 Ma may have been caused by the rising plutons. If so the 800 sq km exposure Akuna Intrusive Complex at the SE end of the Bena Bena terrane may have been the focus of uplift and supplied the metasedimentary detritus to the Finisterre Range. This suggests that the Finisterre Range was not far removed from the Bena Bena terrane, perhaps less than the 200 - 400 km indicated by Abbott et al (1984). The Akuna Intrusive Complex probably resulted from subduction of the Solomon Sea Plate beneath the PNG margin. In order for the subducted slab to reach depths of -100km below the area to facilitate partial melting and plutonism (Hamilton 1994), subduction probably commenced 3-5 Ma Ma before plutonism, ie at or prior to 20 Ma suggesting a significant change in the tectonic regime at -20 Ma, perhaps related to collision of the Solomons - Ontong Java Plateau collision (eg. Hall 1997). The main result to emerge from the 28 apatite fission track analyses is that the whole of the study area underwent rapid cooling due to uplift and denudation in the Late Miocene, mainly between 7-10 Ma. Results from several samples indicate that they were not totally overprinted prior to uplift indicating maximum burial of -3 km in the Middle Miocene, assuming normal temperature gradients. The burial is less if higher gradients are assumed, allowing for Middle Miocene plutonism. The Late Miocene cooling in the Mobile Belt agrees well with the Pliocene to Recent cooling in the Fold Belt to the SW, interpreted to be due to uplift and erosion associated with fold and thrust deformation of the Miocene Limestones (Hill & Gleadow 1989). This timing relationship suggests, that compressional deformation in the Mobile Belt occurred in the Late Miocene, at 105 Ma, and that the deformation migrated towards the undeformed foreland in the southwest in the Pliocene, at 5-2 Ma. The regional Late Miocene uplift and denudation in the Mobile Belt is also consistent with that postulated by Crowhurst et al (1996; 1997) for northwest PNG, although they considered the event to have occurred mainly from 8-5 Ma. If so, then the uplift and denudation may have been migrating from east to west as well as to the south into the Fold Belt. These timing relationships place significant constraints on tectonic models for the area, indicating that the major compressional pulse in PNG commenced in the northeast at -10 Ma and migrated to the southwest and west in the latest Miocene to Pliocene. This suggests that the initial arc-continent collision and associated shortening occurred in the Late Miocene around -10-12 Ma. This immediately followed intrusion and cooling of the Akuna Intrusive Complex at -17-14 Ma and the Bismarck Intrusive Complex at -12.5 Ma (Page 1976), indicating a linkage between the end of plutonism and the start of compressional deformation. The timing is consistent with the observation of Hamilton (1994) that in areas of subduction `the common regime in overriding plates is extensional and leading edges are crumpled only in collisions. This suggests that the Middle Miocene magmatism in northern New Guinea occurred during extension above a subducting slab and was terminated by Late Miocene arc collision and resultant compression commencing at -10-12 Ma. In general, these data indicate that the acme of denudation and cooling in the Mobile Belt was in the Late Miocene, with relatively little denudation there since. In contrast, Hill & Gleadow (1989) found that the peak of denudation in basement outcrops in the Fold Belt was in the Pliocene at -4 Ma. However, in this study some samples from the Mobile Belt yielded Pliocene ages or high

Jan 1, 1997

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By G K. Robinson

The existence of bias in samples taken by cross-stream sample cutters has been investigated using three-dimensional discrete element method (DEM) modelling. Detailed quantitative information on overall extraction ratios, size specific extraction ratios, missed and extra sample components can be made by comparing a reference sample to the actual sample. A key advantage of using this modelling approach over physical experimentation is that the reference sample can be measured on precisely the same portion of the stream of material as the actual sample, thereby allowing the elimination of a significant fraction of the variability and allowing statistically significant results to be obtained using many fewer replicates. Quantitative analysis of results broadly supports the commonly-used rule that the cutter aperture should be at least three times the nominal top-size of the material being sampled, but does not support the commonly-used rule requiring increase in cutter aperture if the cutter speed exceeds 0.6 m/s. Sampler performance can be understood in terms of the balance of forces in the congested region of material formed by the slowing of the particle stream due to collisional interactions around the mouth of the cutter.

Jan 1, 2008

By Baker G

Chromite was recorded among the rare minerals in the natural beach sand concentrates on the coast of Northern New South Wales by Whitworth(l) in 1931, and the commercial production of zircon and rutile from these beach sands has yielded concentrates of ilmenite with small amounts of chromium. The chromite is a detrimental impurity in the utilisation of the ilmenite, and the difficulties that attend the separation of the small amount of chromite from the ilmunite have raised suggestions from time to time that chromite occurs with ilmenite in composite grains. The absence of such composite grains and the nature of the chromite grains has been indicated by the following mineragraphic examination of magnetic concentrates containing chromite which were prepared by the C.S.I.R. Ore Dressing Laboratory, Melbourne University, from ilmenite concentrates from beach sands at Norrie's Head, County Rous, New South Wales and Stradbroke Island, Queensland.The magnetic concentrates from each locality are divided into five fractions, and the No. 1 concentrate is the most highly magnetic and the tailing the least magnetic. Chromium assays as determined by the Ore Dressing Laboratory are as follows:-

Jan 1, 1948

Goodenough and Fergusson Islands, in eastern PapuaNew Guinea, lie in an area of crustal extension on the western end of the Woodlark Basin seafloor spreading system. The islands are made up of a number of mountainous domes of complexely deformed basement, and these are intruded by large bodies of granodiorite. The domes are bounded by curved shear zones and faults dipping outwards at angles of around 25 to 45¦. The cores of the domes contain lower crustal rocks of eclogite and granulite facies, these rocks have undergone retrograde metamorphism in the outer sheared zones. Movement indicators on the shear zones indicate a complex moverm.-It geometry which does not fit the models proposed by earlier workers. These dome-like structures are similar to the metamorphic core complexes of the western United States Cordilleran region, however there are a number of aspects which do not fit with the models proposed for the development of metamorphic core complexes. Uplift of the metamorphic basement probably resulted from a combination of forces associated with the extension of the crust and the intrusion and emplacement of granodiorite plutons.

Jan 1, 1990

Thank you for the invitation to address The AusIMM Young LeadersÆ Conference here today. When I first saw the conference theme û æadvancing technologies and their future applications in the mining industryÆ û my interest was sparked because there is little doubt that technology and technological advances will determine the relevance of this industry in the future. And the people seated here today are major players in determining the minerals industryÆs destiny.During my 20-year association with the mining industry, I have observed a number of significant changes that have been delivered as a result of the vision of technical specialists. These changes have built a more competitive industry, a more socially acceptable industry and most importantly an industry with ever-improving safety performance. The purpose of my address is to attempt to provide a context and foundation for other presenters over the following two days. Today, I wish to try to answer the question, æWhy do we invest in new technology in the mining industry?Æ, via: a brief history lesson, a review of the needs of the business, a look at the process for improvement, and finally an example from WMC ResourcesÆ current technology portfolio. I would like to take a very brief walk back in time. During the iron and bronze ages, whilst our ancestors IÆm sure never spoke the phrase ænecessity is the mother of inventionÆ, I am sure they lived by it. Undoubtedly more so than we do today. The roots of geology, mining and extractive metallurgy grew out of the need for better tools in order to get access to the basic necessities of life. It was their superior ability to generate and deliver these ætechnologyÆ improvements that underpinned great civilisations such as the Egyptians, Romans and Incas. The application of mineral technology improvements by these civilisations was crucial to their success, it was their competitive advantage at the time. Many historical texts include detailed descriptions of both mining and processing fundamentals that formed the basis of many of todayÆs operations and processes. However, it is technological improvements to these fundamentals, as well as the development of new technologies, that have preserved the fundamentals as viable options for the industry today. Even in my time in the industry, there have been substantial improvements in the way business processes operate. When I first started working in a gold mine in WA in the late 1980s, the office had one PC (a 286 processor). All data was managed by paper and then often re-typed into other databases. Electronic mine design and process control was in its infancy. Today, massive amounts of data are recorded, analysed and acted upon almost without any human interaction. Our industry today has far different challenges than those described by Argricola. These are many and diverse, but new technologies are required to address three distinct classes of need: 1. Societal needs: physical needs for food, shelter, recreation and leisure; community and political needs for less waste, less emissions, better safety and working conditions, less energy consumption and sustainability. 2. Individual needs: intellectual needs to create innovative technical and organisational ideas. 3. Wealth generation needs: investor needs for maximising operating efficiency and value growth. Each new technology, to varying degrees, fulfils one or all of these needs. In many cases, the driver of a technological development was to fulfill only one of these needs, but after it was implemented, the development actually fulfilled each need. I would like to expand on these needs.

Jan 1, 2003

By J Zhang, L Klemettinen, A Jokilaakso, J Biswas, J Partinen, H O’Brien, A Klemettinen

Waste lithium-ion batteries (LIBs) are important secondary sources of many valuable materials, including Critical Raw Materials (CRMs) defined by the European Union (EU): lithium, cobalt, manganese, and graphite. Additionally, LIBs typically contain nickel and copper, which are classified as Strategic Raw Materials for EU since 2023. In recent years, great effort has been made to develop efficient recycling processes for waste LIBs. Pyrometallurgical processes have been essential in industrial production of metals for many decades. These technologies are relatively mature, with high adaptability for different raw materials. Pyrometallurgical treatment in LIB recycling typically involves the use of smelting processes, in which waste batteries are heated above their melting points and metals are separated through a reduction reaction in the liquid phase. Through this recycling route, cobalt, copper, and nickel can be efficiently recovered in the form of a metal alloy, whereas lithium and manganese are lost in the slag phase. The goal of this work was to increase the recoveries of valuable battery metals through a combination of hydro- and pyrometallurgical unit operations. First, industrial Li-ion battery scrap underwent a selective sulfation roasting stage, where the aim was to transform LiCoO2 and Mn-oxides into Li, Co and Mn sulfates. After roasting, the battery scrap was leached in distilled water with a solid to liquid ratio of 100 g/L at 60°C and recovered 95 per cent of Li, 61 per cent of Mn and 35 per cent of Co. After leaching, the solid leach residue was mixed with industrial Ni-slag and biochar, followed by reduction at 1350°C in argon atmosphere. The high-temperature smelting experiments were conducted as a function of time (5–60 mins) to investigate the reduction behaviour of battery metals. The results show that Co and Ni from the slag and leach residue can be efficiently recovered in the slag cleaning stage.

Jun 19, 2024

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By J Borthwick, M Yusi, M Douge

Feasibility studies form a vital and significant component of the project delivery cycle. They are at the heart of the valuation process. This paper focuses on variables which can affect a project and how these are assessed as part of the decision-making process through feasibility studies. Test work and site selection needs; the degree of engineering required to meet the study requirements and the quality of owner project information are discussed. Also, local factors including permitting needs, social, environmental and government relations are considered. Engineering and site factors are crucial in the estimating process. The interaction of detailed engineering, engineering assumptions and estimating methodologies are therefore examined. The ownerÆs perspective is considered along with risk analysis, which is fundamental in project feasibility study activities. The impact of this is also discussed.

Jan 1, 2009

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

We are moving into an era where we experience the consequences of the skills crisis û namely many resource models have been generated by inexperienced people under pressure to deliver high quality resource estimates in unsupported environments, often without technical mentors. These resource models form the basis of our decision to pursue actual mining. This begs the question: how valid are the resource models that form the basis of our mining decisions? This paper presents various model validation tools such as comparison of input and output statistics, swath plots, sectional or bench comparisons between drill holes and models as well as a variety of other approaches. Each model validation tool currently used in industry is examined:how the tool generates results,what assumptions exist,what constitutes a pass/fail in the test, and what interpretations to consider when using the validation tool. Each validation toolÆs suitability and the inherent flaws in the underlying assumptions are also discussed. These are supported with examples of good versus bad validations. Our principles based reporting codes provide flexibility in how models are generated and what approaches and/or parameters are used to generate resource estimates. This flexibility works well when used by experienced practitioners. However, our reporting codes assume a level of experience not always available in the current skills crisis. This paper seeks to provide minimum model validation prerequisites for model acceptance and suitability, regardless of the resource analystÆs experience. As we move forward, our immediate challenge is to ensure our baseline resource models are material, transparent and competent.

Jan 1, 2009

By Dickin FJ

Advances in the development and application of in situ imaging of mineral processing operations using electrical tomography techniques are reviewed and illustrated with case studies relating to pneumatic conveying, mixing and centrifugal separation processes. The potential for applying these methods to full three-dimensional visualisation of the dynamic behaviour of flow in pipelines and separators, and the resulting consequences for process-modelling strategies, are discussed.

Jan 1, 1993