Search Documents

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By E Portes, G Noble, J Roberto, A Stabile

Iron ore beneficiation plants are facing economic pressures to treat more challenging ore types, improve efficiency and improve product quality. Better control and stability of the plant process in the face of increasing feed ore variability has been a goal for many of the operations facing these challenges.Prompt gamma neutron activation analysis (PGNAA) technology has proven to be a successful measurement technique within an iron ore beneficiation plant. PGNAA was first developed in the early 1980s for the measurement of the elemental composition of bulk materials. Today, PGNAA technology is applied for elemental analysis within the iron ore industry on both bulk materials and slurries.Traditional composite sampling throughout the wet iron ore beneficiation process provides a delayed measurement of average properties but does not capture the true variability of the process in real-time. As such this is a limiting factor towards stabilisation and optimisation of the process. A PGNAA analyser provides real-time slurry elemental analysis of feed, concentrate and tails streams within the processing plant. The analytical data from the analyser can be exploited with a control strategy to correct and stabilise the plant on a much shorter time scale, delivering significant economic benefits and greater operational flexibility. The economic benefits include more stable product quality and a reduction in composite sampling and laboratory costs.Some example results will be presented from the Vale Vargem Grande iron ore beneficiation plants, which are utilising a six stream multiplexed Thermo Scientific PGNAA Slurry Analyser.CITATION:Noble, G, Stabile, A, Portes, E and Roberto, J, 2017. Real-time slurry elemental analyser for iron ore beneficiation plant control, in Proceedings Iron Ore 2017, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The following paper deals with a method for the" Proximate Analysis" of Chloridized Ores, which are free from arsenic, antimony and lime. When these are present the analysis is rendered far more complicated, and many of the methods which I am about to describe could not be applied. Sufficient scope is therefore offered for discussing the analysis, when these metals are present, in a separate paper, which I hope to contribute at a future date.I am fully aware that this method is far from being perfect. No doubt many, modifications and improvements will suggest themselves to my readers, and I trust that this paper will be the means of giving a certain impetus to the study of Proximate Analysis which at the present time is practically dormant. For the benefit of my readers who are not initiated into the details of ordinary estimations, I have briefly described well known methods, which, however, will be found fully described in most text-books of analysis. Assuming that the ore contains. sulphates and chlorides of soda and magnesia, sulphates, sulphides, chlorides and oxides of copper, lead, iron, zinc, manganese and silver chloride, the analysis would be conducted as follows. The first compounds to estimate are the chlorides and sulphates of soda and magnesia.

Jan 1, 1901

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

Determination of Flotation Kinetics of Coal Grain Types in a Pilot Scale Jameson Cell using Coal Grain Analysis Method

Sep 13, 2010

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Sapporo-Iwanai district is located at the intersection of the northeast Japan arc and Kuril arc, associated with the subduction zone. This area is characterized by Miocene submarine volcanism followed by Plio-Pleistocene subaerial volcanism.   Koryu, a small epithermal Au-Ag deposit, occurred in Pleistocene (1.4 - 0.85 Ma) within Miocene sedimentary rocks near a subaerial andesitic volcano, while Toyoha, a large epithermal Pb-Zn-Ag (-Au) deposit, also occurred near a subaerial andesitic volcano. Although most of the base metal deposits formed in middle-late Miocene, Toyoha formed in Plio-Pleistocene (2.93 - 1.60 Ma) within Miocene volcanic and sedimentary rocks. This epithermal mineralization was partly overprinted by xenothermal Cu-Sn-In(-Au) mineralization (2.68 - 0.49 Ma).   Hydrothermal alteration differs vastly between Koryu and Toyoha: host rocks at Koryu were not intensively altered, although wall rocks adjacent to veins were silicified, while those at Toyoha show intensive and extensive neutral-pH alterations. Geological and chronological studies show that middle~late Miocene (12.5 - 8.4 Ma) alteration was pervasive and overprinted by Plio-Pleistocene (2.93 - 0.49 Ma) alteration. The base metal veins in the middle-late Miocene were not well developed, but were large in number with great depth.   These studies show that the hydrothermal activity at Koryu is rather small and short-lived, while that at Toyoha is large, long-lived and characterized by overprinting of different hydrothermal systems. The subaerial magmatic activities yielded not only the andesite lavas, but also generated hydrothermal solutions for the formation of both Koryu and Toyoha. The metals were possibly derived from such magma. At Toyoha, the hydrothermal solutions could also remobilize metals from old ores.   The size, life span of magmatic-hydrothermal system, and overprinting on the old mineralizing systems could constrain the type of metal deposits (precious and polymetallic deposits) nearby subaerial andesitic volcanoes in Plio-Pleistocene.

Jan 1, 2005

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

This paper describes the programing and specification requirements which affected the choice of excavation methods on the Melbourne Underground Rail Loop (M.U.R.L.). The various methods that were chosen are briefly described, and the three most used are compared in more detail. Excavation rates, cycle times and other statistics are compared for full face tunnel boring, full face drill and blast, and heading and bench using a road header excava- ting machine. The length of tunnel excavated is sufficient to enable meaningful statistics to be presented and the significant specifi- cation and geological factors are described to weight the statistics where necessary for purposes of comparison. Average tender prices are given for excavation and primary support to indicate the reimbursement sought by contractors to carry out this type of tunnelling.

Jan 1, 1981

By Carr SD

The Omineca Belt of the Canadian Cordillera straddles the western boundary of the North American paleocontinental margin and accreted oceanic and island arc terranes. Crustal thickening of the orogenic belt was initiated in the Jurassic and culminated in latest Cretaceous and Paleocene times.Thin-skinned shortening of the Rocky Mountain Foreland Thrust and Fold Belt was balanced by basement-involved crustal imbrication within the Omineca (hinterland) Belt. Middle and upper crustal rocks of the hinterland (Selkirk allochthon) were thrust eastward and ramped onto basement of the North American continental margin. By latest Paleocene the southern Omineca Belt formed an elevated crustal welt that was at least 60 km thick.Within less than 3 Ma of the culmination of crustal thickening the belt was rapidly uplifted and tectonically denuded. The southern Omineca Belt was extended by as much as 80% as upper crustal rocks were displaced on moderate to low angle normal sense shear zones and brittle normal faults. This oro-genic collapse is interpreted to be a gravitational response to crustal thickening and thermal soft-ening, facilitated by reduction in plate-boundary-induced far field stresses.

Jan 1, 1990

By Gartrell H. W

During investigations of the treatment methods for ore from the Bird-in-Hand gold mine carried out at Kalgoorlie and at these laboratories, it was found that excess alkali caused a lowering of extraction by cyanide, the cause of this being attrIbuted to the presence of a small amount of oxidised lead compounds in the ore. The subject has been discussed by various writers,3 but no satisfactory explanation of existing facts has been put forward. The experiments described in this report have been carried out with the object of obtaining some insight into the chemical reactions underlying the effect of lead salts and alkalis in cyanidation.The formation of cyanide-insoluble coatings on gold during roasting with lead compounds is well known, but the adverse effect of alkalis in cyanidation of ore is *This paper represents work done under a co-operative agreement between the Commonwealth Council for Scientific and Industrial Research and the South Australian School of Mines and Industries.Published by permission of the Mining Advisory Committee, Commonwealth Council for Scientific and Industrial Research.

Jan 1, 1935

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004