Search Documents

By H. C. Goodrich

At the Utah Copper mine, steam shovels were first used, in 1906, for the removal of overburden, and in June, 1907, for the mining of ore. Prior to 1907, the ore came from underground development work and from stoping. The use of the steam shovel gradually increased until 1914; since then all material, both overburden and ore, has been loaded by power shovels operating on the various benches of the mine. During these 19 years, there has been a great improvement in open-pit mining, largely in the use of equipment having greater capacity and dependability. The history of the development of mechanical shovels and related equipment, as affecting the Utah Copper Co., would be interesting and would justify considerable space; but of greater interest at this time is the operation of the equipment now in use. The Utah Copper mine is in a great deposit of copper-bearing monzo-nite, which occurs as a prominent headland of the Oquirrh range of

Jan 1, 1925

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By William F. Haddon, Phillip J. Maddex

Marco Polo brought the first borax to Europe late in the 13th century. It was especially treasured then for one of its many qualities-that of working with gold as a soldering flux. Georgius Agricola in 1556 gave it the name chrysocolla (which the Moors called borax)-literally, "gold glue." Deposits of borax have been elusive and widely scattered-first found only in Tibet and Italy, and, in 1836, at Iquiqui, Chile. Dr. John Veatch made the first California discovery in 1856 while examining a mineral spring east of Red Bluff. This "Borax Lake" soon supplied 90% of U.S. demand, but flooding and other production problems caused the scene to shift from Borax Lake to Little Borax Lake and then to Nevada in 1871. Early transportation was by "Twenty-Mule Teams."

Jan 1, 1971

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1943

By Kurt Stock

The grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: Total, Not Leap, Iron, Cadmium, Over. Per Per Cent. Per Cent. Per Cent. Cent. A. High grade.................. 0.07 0.03 0.05 0.10 B. Intermediate................ 0.20 0.03 0.50 0.50 C. Brass special................ 0.75 0.04 0.75 1.20 D. Prime western............... 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages. Smelters engaged in the smelting of custom ores had occasional complaints about the quality of their metal, as some of the consumers, especially brassmakers and some galvanizers, used the rigid standards of the A. S. T. M. as a basis for obtaining redress from zinc smelters whenever some of their work was faulty. Indirectly, much good resulted from such complaints; for while the brassmakers and galvanizers, on the whole, did not know what was wrong, the metallurgists in charge of zinc smelters were induced to abandon their conservatism and study the influence of impurities in spelter from the point of view of the consumer. For some of us, spelter gradually ceased to be considered merely spelter; it

Jan 1, 1925

By Basil Prescott

Resume.-The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre¬mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide types occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore. The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition.

Jan 2, 1915

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By C. E. Sims, H. M. Banta, S. L. Hoyt

Over the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking— specifically underbead cracking, or "hard cracks," or parent-metal cracks-—is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.' The tests described are made under restraint to facilitate cracking and arc so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when are-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institutc on two projects, one

Jan 1, 1945

By H. O. Hofman

The substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared; also some illustrations have been added. Blast-roasting* is a generic term for the process of forcing air through finely-divided metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore niight be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the

Jan 1, 1911

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

MINING, to be precise, ends when the ore is delivered to a bin outside the mine. Usually the next step is concentrating; or, as it is more often called, milling. A few elementary definitions will help make clear the discussion that is to follow. A rock is an aggregate of minerals; copper ore is rock that contains copper-bearing minerals in quantity sufficient to make it profitable to mine and recover the copper in the form of marketable metal. Manifestly, under a literal interpretation, a mass of material might be copper ore one day and merely copper-bearing waste rock a week later, if the price of copper happened to drop in the interim. Emphasis already has been placed on the expansion that took place in the ore reserves of the Porphyry companies as a consequence of the great strides made in the technique of mining and ore treatment. So, even if one inserted a qualifying phrase, "at an average price for the metal," after the word "profitable," the definition would still be open to criticism. Place is another factor. It is evident that a body of excellent ore in Arizona might cease to be ore in the economic sense if it were moved intact to the interior of China. However, it is with ore in its technical and scientific aspect that this chapter is concerned. Speaking in general terms, the ton of Porphyry ore as it arrives at the surface contains 25 to 70 lb. of copper minerals in the form of disseminated particles or thin coats along fracture planes. When subjected to appropriate treatment this ton yields 12 to 40 lb. of metallic copper. These ranges take into account conditions of today and of 25 years ago. Two procedures are available: (1) concentration, followed by smelting of the concentrate, or (2) leaching and precipitation, usually by electrolytic deposition. Smelting and leaching are metallurgic processes in that they involve chemical change; concentration

Jan 1, 1933

By Raymond B. Ladoo

ABRASIVES include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical action polishes and cleaners may also contain solid abrasives; for example, many metal polishes. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains

Jan 1, 1949

By Marcus A. Grossmann

This paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron. Absence of Carbon We may turn at once to the effect of the presence of alloys. It has been found that in the complete absence of carbon, the gamma change will sometimes disappear entirely when sufficient alloying element is

Jan 1, 1927

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others, developed on land by, means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action -proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.1 Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in. the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have. arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with

Jan 6, 1926

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932