Search Documents

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thick-ners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter. It is quite apparent from reading the literature that Coe and Clevenger's contribution is not generally appreciated. In so far as the basic engineering relationships are concerned, the only real advance which has occurred in the 30 odd years which have elapsed since the Coe and Clevenger paper is the recognition of the effect of the rakes on the thickening process. Bull and Darby2 noted this in 1926, and the extensive use of the "gluten type" thickener, in which the effect is magni-fied, bears witness to its importance. Comings3 further verified this effect of the rakes. As a matter of fact, a number of papers show an apparent regression from the Coe paper in that the area determinations are made on the basis of a single test from One concentration of solids. Coe and Clevenger amply demonstrated that this is unsafe, since the controlling zone may be one other than that of the feed dilution. Comings3 neatly demonstrated this without apparently realizing it. Of course there have been significant advances in the application of the operation to industry. Open tray thickeners were introduced to save area; balanced tray thickeners, washing thickeners, and multifeed clarifiers were developed with all of their special hydraulic and mechanical problems. Combinations of all kinds have been introduced, such as combination agitators and thickeners, combination flocculators and clarifiers, combination thickeners and filters. With the establishment of the operation on a firm engineering foundation, installation was facilitated and expansion proceeded. There are still problems, of course, functional as well as mechanical. Sometimes the moisture in the underflow obtained in practice is not as low as is expected on the basis of the test data. Sometimes the underflow is so "thick " that its discharge and subsequent handling requires special attention. Island formation plagues some operators. The use of the thickener as a surge basin and blending tank in the cement industry poses unusual problems. Design of rakes and the drive mechanism must be continually im-proved. Corrosion problems must he overcome. Power requirements for raking the settled solids occasionally is the controlling factor as it was in the case of the all American Canal desilting installation. Other similitude relationships and design problems come into the picture when we enter the field of clarification or nonline settlement. We have an energy dissipation problem in introducing the feed and any models must satisfy the Froude model relationships. Autoflocculation requires detention which involves the same similitude laws that we encounter in the compression zone. Approach to an Exact Science The next step beyond having control of the similitude relationships is to understand the why of these relationships right back up the line to first principles. The ultimate might be that, if given the mineralogical composition of the solids and their size distribution together with an analysis of the suspending liquid, we could calculate the entire thickening behavior of the system. Then we could say we had reduced the operation to an exact science. True it might be more trouble getting this basic analytical data than to make our empirical determinations for area and volume, and we would need an ENIAC to calculate the results, but that does not detract from the desirability of such understanding. Considerable work has been done by the chemical engineers with this end in view. Comings,3 Egolf,4 Work,5 Kam-mermeyer,6 Steinour,7 and others have studied the problem. The writer has no final answer to the thickening story but would like to propose a picture of the mechanics of the two phases of thickening which has been found useful in understanding the subject and which leads to some convenient relationship in treating the compression step and arriving at the compression depth.

Jan 1, 1950

By AIME AIME

ON the afternoon of Feb. 20 of this year a new volcano was born in the center of the State of Michoacan, Mexico, about 100 miles inland from the Pacific Coast. Creation of this new mountain - forming crater began on an almost flat cultivated field at the south margin of a small basin about a mile in diameter and having an altitude of approximately 6800 ft. above sea level. This basin is connected to a gently inclined plain that forms the Parangaricutiro valley, the chief town of this municipality, bearing the same name as the valley, being situated three miles from the site of the new crater. The village of Paracutin, from which the new volcano received its name, is about one mile to the northwest of the crater. From the City of Mexico to the volcano is a distance of 330 miles. The paved highway running from Mexico City to Guadalajara, by way of Toluca and Morelia, is left at Carapan; from here another paved branch highway goes to Uruapan. The town of Paracutin is reached by a narrow dirt road 18 miles from Uruapan and connects with a road leading to Parangaricutiro where horses may be hired for a 40-minute trip to a place where visitors can enjoy a magnificent view of the volcano. It is possible to get within half a mile of the point of eruption in this manner.

Jan 1, 1943

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.&apos; Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By J. Nutting, D. H. Kirkwood

IT is clearly of great metallurgical interest to know the conditions of temperature and gas composition under which different products will form in sulphide roasting. A method of graphically presenting the relevant thermodynamic data will be demonstrated, such that these conditions are readily obtainable. The products of sulphide roasting may be oxide, sulphate, or oxysulphates, and the equilibria between these may be represented in the following way: 2 MSO4 = MOMSO4 + SO3 MO-MSO4 = 2 MO + SO3

Jan 1, 1961

By Alexander L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron

By G. W. Jones, G. S. Scott

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer&apos;s intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist&apos;s knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By G. S. Scott, G. W. Jones

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer&apos;s intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist&apos;s knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By A. L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron-

Jan 1, 1873

By E. H. Snow, B. E. Deal

Instability effects in semicanductor devices have long been attributed to the motion of charges on or within oxide layers on the surface. These effects are of critical importance in metal-insulator-semiconductor MIS) field-effect devices. For this reason, the capacitance-voltage or the conductance-voltage characteristic of these devices can be used as a sensitive detector to study charge transport and polarization effects in the oxide or insulator. A review is given of the results of such studies of thermally grown SiO2 as well as of other insulating films of importance in silicon technology. Three types of effects are distinguished. The first of these is the drift of mobile cations within the dielectric, examples being thermally grown SiO, which is often contaminated with sodium ions, and a variety of other glasses in which the mobile ions are a part of the glass composition. The second effect is a dipole-type polarization which occurs in phosphosilicate glass films obtained by reacting P2O5 with thermally grown SiO2. The third effect involves the transfer of charges between the dielectric and the silicon electrode. This occurs in silicon nitride and other deposited dielectrics. It is concluded that MIS studies have provided a powerful technique joy the study of charge transport and polarization effects in insulating films. The knowledge gained from these studies has led to an understanding of surface effects on conventional transistors and diodes as well as making possible stable MIS transistors. THE metal-insulator-semiconductor field-effect transistor is conceptually the oldest type of active semiconductor device.&apos; The earliest attempts at making this device were frustrated because of high surface state densities at the interface between the semiconductor and the gate insulation.&apos; However, by using a silicon substrate with thermally produced silicon dioxide as the gate insulation, this problem was solved and metal-silicon dioxide-silicon devices with good characteristics were made as early as 1960. 3 Yet it was still over 5 years before these devices became a commercial reality. This delay was largly due, not to surface states, but to stability problems associated with polarization effects within the insulating layer which caused the threshold voltage of the device to drift under temperature and bias treatments. The solution to these problems has not only made possible stable MIS devices, but it has added immensely to our understanding of failure mechanisms in conventional bipolar transistors and has added to the reliability of ali types of planar devices. In this review, we shall first describe the effects of various types of polarization phenomena on MIS device characteristics. Then, since thermally grown SiO, is by far the most important insulator used in these devices, we shall review historically the type of instabilities which have been observed in thermal oxides, the attempts at understanding and eliminating them, and the present status of the problem. We shall then turn our attention to the various deposited insulators which have been used, including lead glasses, phosphosilicate glass, vapor-deposited silicon oxide, and silicon nitride. Interestingly enough, many of these materials show polarization effects which are quite different from those generally observed in thermally grown SiO2. THE EFFECTS OF POLARIZATION PHENOMENA ON MIS CHARACTERISTICS The simplest MIS device and the one which has been most frequently used in the study of polarization effects is the MIS capacitor. Two modifications of this structure with single- and double-layer dielectrics are illustrated in Figs. l(a) and (b), respectively. The capacitance of this structure as a function of voltage applied to the metal gate electrode is plotted in Fig. 2 for the case of an n-type silicon substrate. When the silicon surface is accumulated (positive bias) the measured capacitance is just that of the insulating layer C. When the surface is inverted (negative bias), the capacitance is that of the insulator and a silicon depletion layer in series CoCs/(Co + Cs). Indicated on the horizontal axis of Fig. 2 is the voltage VT at which the silicon surface becomes strongly inverted. This voltage corresponds to the threshold or turn-on

Jan 1, 1969

By M. R. Tek, K. H. Coats, D. L. Katz

In natural gas storage operations, seasonal pressure fluctuations in the gas reservoir cause the water from the surrounding aquifer to flow into and out of the gas sand. The theory of unsteady-state liquid flow through porous media developed by Van Everdingen and Hurst&apos; has been applied to predict the water movement into and out of the gar bubble for .several .postulated pressure cycles. Those cycles with as many pound-days above the original aquifer pressure as pound-days below, may cause the gas reservoir to slowly grow or shrink rather than hold to a constant volume. Applications to an actual field case study give the predicted gas reservoir monthly pressures and volumes as compared with the observed monthly pressures and volumes. INTRODUCTION A large number of natural gas storage reservoirs are bounded by or adjacent to large water-saturated formations called aquifers. The presence of these aquifers is usually evidenced by the production of water from wells delineating the gas-hearing sands. Some gas storage reservoirs in use today have been purposely developed on aquifers. Cyclic pressure variations in a gas storage reservoir cause water influx and efflux from the surrounding aquifer. This, in turn, results in a varying gas reservoir volume. The prediction of the effect of this aquifer fluid movement on the size and size variation of the gas reservoir can provide information valuable in the study of several reservoir engineering problems. The economics of gas storage operations are directly influenced by the influx of aquifer fluid into the reservoir since a shrinking storage reservoir requires increasing pressures for the storage of the same quantity of gas. Material balance and reserve or recovery calculations also obviously require knowledge of reservoir volume. Various other reservoir engineering calculations such as interpretation of well interference data, evaluation of physical characteristics of porous media, water coning, gas injection and pressure maintenance studies are typical problems where variations of volume due to edge or bottom-water encroachment becomes important. The solution of equations describing influx and efflux of water in the gas sand, application to gas storage reservoir behavior and interpretation of results are the main objectives of this paper. While this work was directed toward gas storage reservoirs, it applies equally well to repressuring of partially depleted oil reservoirs with an active water drive. MATHEMATICAL ANALYSIS As just mentioned, the cyclic pressure variations in an aquifer-surrounded gas storage reservoir cause water movement and varying gas reservoir volume. Prediction of this volume variation from the reservoir pressure cycles or the injection-production schedule requires adoption of a flow model, certain assumptions concerning reservoir and fluid properties, and formulation and solution of the governing differential equation. The flow model used in this study is a gas bubble located on a very large aquifer (Fig. la). Gas bubble radius and aquifer sand thickness are denoted by rr and h, respectively. Fig. lb shows the horizontal, radial two-dimensional porous reservoir attended by the unsteady, compressible motion of the aquifer liquid. Volume variation of the gas bubble is determined from aquifer water flow across the cylindrical boundary, r = r0

By Henry E. Colton

Very little information has been published concerning the Tennessee coal-field. The State never appropriated over $600 per annum for a geological survey, and that was discontinued about 1870. Yet even with that small sum Dr. J. M. Safford made a

Jan 1, 1886

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

By Arthur Hockman, Howard W. Jaffe, Howard F. Carl

THE problem of establishing practical techniques for evaluating natural corundum ores arose from the desire to improve the existing purchase specifications for crystal corundum procured by the Federal Government for stockpiling. Such purchase specifications had been developed for a large number of products, including minerals and ores considered to be critical and strategic because of the country&apos;s dependence on foreign sources of supply. It will be apparent to anyone considering the subject of purchase specifications that the determination of whether or not a submittal meets the specifications is a prime consideration. Consequently satisfactory specifications for minerals should not only incorporate physical, chemical, and mineralogical requirements that are practical but should also establish the means by which both buyer and seller can be assured that materials meet stated requirements. The Munition Board&apos;s Material Purchase Specification for corundum, dated February 1954, covered two grades of crystal corundum intended primarily for abrasive use. It established limits of size and of composition: Grade A, at least 95 pct +3 mesh and 92 pct alumina (Al2O3); Grade B, at least 95 pct +7 mesh and 90 pct alumina. It also specified that "of each lot of material, not less than 95 percent shall have a hardness equal to or exceeding nine (9) on Moh&apos;s Scale." These specifications were unsatisfactory for several reasons. They did not allow the purchase of lower grades of corundum being used by industry. Neither did they specify exactly what a corundum ore actually was, except that it should contain so much alumina and have a certain scratch hardness. Nothing was said about the abrasive qualities of the material that was to be purchased primarily for abrasive use. During the period 1946 to 1948 supplies of the two grades defined in the then current specifications continued to decrease. Early in 1949 industry recommended that the finer sizes of corundum known as "crystal corundum concentrates," ¼-in. to 16-mesh material, be added to the stockpile specifications and that lower grades of crystal corundum also be included. In the spring of 1949 the National Bureau of Standards and the Bureau of Mines were asked by the Munitions Board to cooperate in developing more practical specifications for grading natural corundum ores. The National Bureau of Standards indicated that it would investigate physical test methods for determining abrasive characteristics of corundum, and the Eastern Experiment Station of the Bureau of Mines at College Park, Md., stated that it would consider the mineralogical aspects of the problem. Members of these two agencies, in consultation with representatives of the Office of Materials Resources of the Munitions Board and of the Federal Supply Service of the General Services Administration, and with the cooperation of industrial suppliers and consumers of abrasive corundum, developed, in a fairly short time, more practical specifications for six grades of corundum ores. The new specifications, issued January 1951, were for corundum, natural crystals, as by this time high-purity synthetic corundum was available and widely used. Nevertheless, for certain specific applications the natural product was preferred over the synthetic material. It has been extensively used in forming snagging wheels. It breaks into more or less cubical particles, whereas artificial corundum fractures into splintery shapes. These produce irregular cuts in glass, while the more symmetrical shape produces a more uniform ground surface. For this reason natural corundum has been preferred for certain types of lens grinding. Pure corundum is clear, colorless alpha alumina (A12O3), but it is rarely found in nature in this form. The most important gem varieties include the blue and yellow sapphires and the ruby. Minute impurities of titanic oxide impart a blue color,

Jan 1, 1955

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,&apos; Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,&apos; they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:&apos; corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

By J. G. Thompson

IRON, iron everywhere, but hardly a particle of pure unadulterated iron for the metallurgist to use as a base for the protean characteristics that he develops in the alloys of iron-the modern steels. Iron, next to aluminum the most abundant metal in the crust of the earth; one of the oldest metals known to man and serving him as the most indispensable metal in both war and peace; yet man&apos;s knowledge of its properties is based on specimens that are not pure and hence probably differ considerably in their properties from the truly pure metal. Purification of iron has brought about startling changes in its electrical and magnetic properties and has modified its behavior in changing its crystal form with temperature, the basis of the heat-treatment of iron. So both the research metallurgist and the metallurgist of the steel plant are intrigued by the possibilities that might unfold were 100 per cent pure iron available in sufficient quantities to determine its properties.

Jan 1, 1940

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

By Henry Sturgis Drinker, Rossiter W. Raymond

Jan 1, 1914