Search Documents

By O. J. Hollister

Jan 1, 1888

By John W. Burd

A system is described for the simultaneous deposition of epitaxial layers on as many as eight substrates. A high degree of uniformity of both physical and electrical characteristics is achieved in the films. Variation of film thicknesses is consistently less than ±10pct within a wafer and from wafer to wafer within a run with the variation typically on the order of 55 pct. Composition variation of GaAs1-x PX layers within a wafer and from wafer to wafer within a run is consistently less than 51 pct. Electrical evaluation of the films by several techniques indicates excellent doping uniformity within a wafer and from wafer to wafer within a run. Mobilities for lightly doped GaAs films at 300°K are consistently >6000 cm2 v-1 sec-1 and mobilities > 7000 cm2 v- 1 sec-1 are regularly attainable. Techniques for the preparation of material with carrier concentrations from 1 x 1015cm-3 to 1 x 1019 cm-3 n-type and 5 x 1016 to 5 x 1018 cm-3 p-type are discussed. METHODS for the preparation of 111-V compounds by vapor phase reactions have been extensively reported in the literature.1-6 Almost all of the apparatus described for these various methods are suitable for processing one or at the most a very limited number of wafers simultaneously. With the recent rapid advances in the use of vapor grown GaAs for microwave oscillators and GaAs1-xPx as visible light emitters the requirements for these materials are steadily increasing. In order to satisfy these requirements it is necessary to move from a laboratory scale apparatus to one which is capable of processing a large number of wafers simultaneously. Desirable features would be a high degree of uniformity among the wafers and good reproducibility from run to run. The apparatus to be described fulfills these requirements very well. DISCUSSION The various methods reported in the literature can be classified under three headings: 1) closed tube, 2) open tube, and 3) the close-spaced method. Of these three the open-tube method is the most amenable for scale-up to a manufacturing process. It is the most versatile and the various operating conditions can be more precisely controlled than with the other two methods. A number of chemical reactions may be used to achieve vapor-phase growth of 111-V compounds. Sev-era1 of the more generally used reactions are shown in Fig. 1. All of these reactions have the following points in common: 1) generation of a volatile group III(Ga) species by the reaction of the transport agent (halide or HC1) with either Ga or GaAs, 2) introduction of the Group V(As and/or PI component, 3) a method of adding dopant, if desired, and 4) a region in which deposition from the vapor will occur and form as a single crystal epitaxial film on the substrates. The laboratory scale reactors permit the hot re-actant gases to flow into the relatively cooler deposition zone and pass successively over the several substrates which are arrayed along the long axis of the tube parallel to the gas flow. With this arrangement the composition of the reactant stream is continually changing as solid material is deposited on each successive substrate. As a result of this changing gas composition the reaction driving force also changes from substrate to substrate and the degree of uniformity of layer thickness, doping level, and so forth, is poor. This effect can be partially overcome by imposing a controlled temperature gradient along the deposition region to compensate for change in gas composition. However, even when this is done variations in layer thickness on the order of 30 to 40 pct are common and as high as 50 pct are frequently experienced between adjacent wafers in the tube. To expand this arrangement to a large number of wafers would only increase the nonuniformity from the first to last wafer in the line. From the above discussion the two undesirable features of changing gas composition and temperature gradient become evident. A reactor system which eliminates or minimizes these undesirable features is one in which the apparatus is mounted vertically as shown schematically in Fig. 2. The vertical mounting permits the disposition of a number of substrates on a suitable support so that all wafers are at the same vertical height in the furnace and hence at essentially the same temperature. By using only a single row of wafers the reactant gas mixture passes over only one substrate in its path through the reactor. Thus the two undesirable features of changing gas composition and temperature gradient are minimized. An additional design feature which further minimizes temperature variations is rotation of the substrate holder. Rotation serves to integrate any radial temperature gradient existing around the resistance heated furnace. A photograph of a reactor assembly at the completion of a run is shown in Fig. 3. MATERIAL PREPARATION Apparatus. Although any of the several chemical systems shown in Fig. 1 are adaptable for use in this apparatus the one generally used is System 2, the hydride synthesis system. This system has been de-

Jan 1, 1970

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

G. W. TRAER (author's reply to discussion*).-Prof. Parr's discussion develops two points, upon which it seems desirable to comment. First, as to putting through a large enough tonnage to secure economic operation. At each manipulation of each oven 1500 1b. (680 kg.) of coal will be charged and the resultant coke discharged from a like amount of coal. . Sixteen slabs will be discharged at each manipulation, each approximately 5 ½ in. by 11 in. by 6 ft. (14 cm. by 28 cm. by 1.8 m.). The operating schedule of a commercial plant, based upon our observations and calculations, indicates a "through put" of at least 12 tons of coal per day for each oven. We have made these figures conservatively and feel confident of materially exceeding them in a fully developed operating system. Our oven plant, with containers, will not cost as much as high-temperature plants of the same capacity. They do not require container equipment; but this is much more than offset by the cost of the great basal heat regenerative flues. Our operating requirements are quite susceptible to the application of mechanical devices and we believe our labor cost will be well within the necessary limit. Second, as to Fig. 1 in my paper, showing the specific gravity' of the tar. It Was not intended to show that the specific- gravity of -the tar rises With decreasing heat, since of course the contrary is the fact. One of the curves shows the relation between temperature and specific gravity and the other the relation between temperature and- yield. Our consulting engineer prepared the chart according to his customary method for showing two dimensions.

Jan 1, 1919

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By G. Willard Quick

TENSILE tests of rail steels at elevated temperatures'' have shown that certain rails, in addition to having low ductility in the well-known bluebrittle range in the neighborhood of 200° C., have marked reduction in elongation and reduction of area in the temperature range from 400° to 700° C. This range of low ductility was called "the secondary brittle range" and the phenomenon, "secondary brittleness." The question naturally arises as to whether this property of the steels would be shown by impact tests performed in the same range of temperature. If so, the impact test, as suggested by Gillett3 would be a simpler and quicker method for the routine examination of steels at elevated temperature than the tensile test. A number of investigators have reported results of impact tests on steels at elevated temperatures, in which the energy absorbed decreased with increase of temperature above 200° or 300° C. Langenberg4 performed Charpy impact tests on several steels at temperatures ranging from room temperature up to 1000° F. (538° C). His results showed an increase in the energy absorbed in specimens tested in the range from room temperature to 200° or 300° C. and then a gradual decrease in the range, 300° to 538° C., the maximum temperature used. Greaves and Jones5

Jan 1, 1932

By C. L. Baker

The district of Catoree, San Luis Potosi, ranks among the first half-dozen silver-producing camps of Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapnni, Mazapil, Palomas, Musquiz, Minas Viejas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (610 m.) in 41/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catoree from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catoree, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to crosivc forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstone?, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains: some of this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution of the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebblcs, and finer detritus. According to tradition, the higher portions of the Sierra Catoree were forested with pines and cedars but none remain within the mining district, although cedar is found farther south in the range. The vegeta-

Jan 1, 1922

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By G. Herget

Finite-element analysis of slopes and a field trial of a slope support system have shown that a considerable potential for excavation reduction exists if slopes are designed with variable slope angles with depth, and if artificial support systems are made an integral part of the slope design. A cost analysis has shown that the savings for a straight 500 ft. high slope with artificial support can amount up to $900 per foot of horizontal pit extension. Horizontal stresses and displacements can be overestimated by up to 100% by employing a two-dimensional finite-element analysis instead of a three-dimensional one. Stress magnitudes differ considerably when comparing results from slope models subjected to a gravity stress field with slope models subjected to high horizontal stresses. Because the latter case appears to be predominant for open pits, slope stability analyses have to be adjusted accordingly. A field trial measuring peak accelerations and displacements has shown that the use of pre- shearing for termination bench blasts, in cases of already heavily fractured ground, can be more detrimental than beneficial.

Jan 1, 1972

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By Alexander N. Mitinsky

UP to a certain limit, the increase of pressure on the diamond-drill increases the rate of progress in drilling. That limit is set by the resistance of the diamonds to compression; and beyond it, the destruction of the stones will involve an. economic loss, both in time and in money. It is, therefore, important to all diamond-drillers to know what is the resistance mentioned. In Europe, operators usually follow an empirical rule, which directs the maintenance of a pressure, on the area-of the bottom of the drilling-tool, of 12 kg. per sq. 4m. For the tools in ordinary use, this is equivalent to 1 kg. per sq. mm. of the diamonds set in the tool So far as I know, American drillers are using pressures as high as 50 to 60 kg. per sq. cm. of the total area of the drill, and the consumption of diamonds (on Denny's authority, 0.2 carats per meter bored) is greater in America than in Europe. But the reason for this difference may be the comparatively larger size of the diamonds commonly used by American drillers. With the assistance of my friend, the late S. Woisslaw, who was the pioneer of diamond-drilling in Russia, I selected from his stock a number of black diamonds, which I subjected in my laboratory to compression-tests. To prepare regular cubes for such tests, as is generally done with other stones, would have been not only costly, but, what is more important, practically useless. I therefore determined, in order to assimilate as nearly as possible the conditions of actual use, to place each sample between a hard plate (corresponding to the rock) and a softer plate (corresponding to the bottom of the tool), into which it would be pressed during the test.

Jan 1, 1906

By Peter N. Calder

This paper deals with the reinforcement of igneous rock slopes at three open pit iron ore trines in northern Canada. The pits involved utilize overall slope angles in excess of 60º with ultimate depths in the order of 250 m. Three case studies are described. The first concerns the reinforcement of a 300,000 Ton undercut rock wedge, approximately 70 m in height. This was accomplished using 20 cm diameter steel bales, installed in 25 cm diameter vertical holes, and a cement-sand grout. The second involves the reinforcement of a 40 m wide diabase dyke which had been continuously failing as the pit deepened. A unique form of rock reinforcement was used in that the entire mass of the undercut dyke was not pinned to the wall. Rather an interlocking effect between individual blocks within the dyke was relied upon. A third concerns the reinforcement of a berm which was undercut by the contact between the ore and waste. This reinforcement was also accomplished using a combination of steel bales, rods and cement grout.

Jan 1, 1982

By S. R. Maloof, W. R. Mitchell, J. A. Mullendore

Preliminary experimental evidence is presented to show that the metallic impurities aluminum, iron, and silicon, and beryllium oxide as found in commercially pure hot-pressed beryllium powder can be reduced to lower Concentrations by Zone -Purification techniques. The reduction in the concentration of aluminum to extremely low levels (10 PPm) is noteworthy, since earlier work demonstrated that aluminum is a major factor contributing to the hot-tearing of beryllium during fusion welding. On the basis of present findings, a method is suggested for producing beryllium metal of improved weldability. EXPERIMENTAL research now being conducted on the purification of beryllium indicates that several of the metallic impurities and beryllium oxide can be reduced to lower concentrations by employing standard horizontal zone-refining techniques. For the preliminary work, commercially-pure hot-pressed beryllium having a purity of 97.84 pct was used. The chemical composition is given in Table I. The hot-pressed beryllium was machined into bars 5/8 by 5/8 by 4 to 6 in. in length. Beryllium-oxide boats which had been conditioned by prior heating in a vacuum of 10"5 mm of Hg at 1100°C for 3 hr were used to hold the beryllium while it was zone melted. The boat with its charge, along with a smaller beryllium-oxide boat containing scrap beryllium to be used for gettering purposes, was loaded into a quartz tube and evacuated to 10-6 mm of Hg. Alter alternately evacuating and flushing three times with purified argon, the furnace tube was backfilled to a pressure of 1/6 atm of A and sealed off by means of a vacuum-tight stopcock. It was then removed from the pumping equipment and mounted on the traveling carriage of the zone-refining apparatus. Heating was accomplished with a 10 kw 450 kc induc- tion heating unit using an induction coil consisting of two turns of 3/16-in. diam copper tubing. Before starting to zone melt, the atmosphere in the furnace tube was gettered by heating the scrap beryllium in the smaller boat to above its melting point and holding at temperature for several minutes. The carriage was then shifted so as to locate one end of the beryllium ingot in the large boat within the induction coil. A molten zone approximately 3/4 to 1 in. was established by loading directly into the ingot. The molten zone was moved very slowly along the length of the ingot. Before each pass was made the procedure for evacuating, flushing, and backfilling, and so forth was repeatedI' Speeds of 1 1/2 and 3 in- per hr were used with up to twelve zone passes. The appearance of a typical zone-refined ingot is shown in Fig. 1. After zone refining, the grains in the ingot appear to be elongated in the direction of zone travel, whilst before, they are essentially equi-axed. A microexamination revealed the presence of a network in the beryllium grains as seen in Fig. 2. Laue spots in back reflection pictures taken of the sample were not sharp, indicating the presence of subgrains in the structure. As can be seen, however, many of the network boundaries cross beryllium grain boundaries. It has been shown by Martin and Moore1 that beryllium solidifies as a bcc structure which then transforms to the hexagonal structure at about 1250oC.It is believed that the observed network is merely the outline of the bcc structure which formed from the melt and are not subgrain boundaries. In order to eliminate surface contaminants, approximately 1/16 of an inch of material was removed from the outer skin of each ingot after zone refining.

Jan 1, 1962

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950

E. A. H. Tays, San Blas, Sinaloa, Mex. (communication to the Secretary*):—The results obtained by Messrs. Hofman and Hayward in their experiments, proving that a low percentage of copper sulphate with a variable percentage of salt, depending on the ore, gives the best results, confirm practical mill-work which I did in 1895. I have none of my notes, taken at the time, to refer to, so have to rely solely on memory, which precludes the conciseness that is alway desirable. In 1894 I took charge of the plant of the San Rafael Company, near Chinipas, Chihuahua, Mex., which at that time was treating a very refractory ore carrying about $15 in gold and from 20 to 25 oz. of silver per ton, the bullion being about 300 fine in gold. The silver in the ore was in the form of a sulphide. Although carrying an average of 0.75 oz. of gold per ton, free gold could rarely be seen by panning, but upon roasting a sample of the ore the gold became visible at once—a result which was discovered by chance and used to advantage later. In order to utilize the old mill to the best advantage, it was decided to use pan-amalgamation after roasting. The roasting, done in a lime-kiln, was similar to the ordinary " burning " operation. The roasted ore was trammed to the mill-bins and crushed by 10 stamps to pass a 30-mesh screen. The pulp was de-watered and fed to four 1-ton pans. My recollection is that upon starting the mill-work, the charge contained 1.5 lb. of copper sulphate and 5 per cent. of salt per ton. From the start the extraction was unsatisfactory and the loss of quicksilver was very large. Experiments were then carried out on a working scale. First, the quantity of copper sulphate was increased 4 oz. at a time; then it was reduced

Jan 1, 1910