Search Documents

By H. M. Roche

MAGNETITE is the important iron ore of New Jersey although bog ore, limonite and red hematite were mined in sizable quantity early in the state's min-ing history. The deposits of mag-netite are found in the Highland area in the northern part of the state. These ores outcrop a broad belt 20 miles wide, extending in a northeasterly direction from Phil-lipsburg, on the Delaware River, to Greenwood Lake, at the southern boundary of the state of New York, a distance of 60 miles. The area in which the magnetite is found (see map, Fig. 1) contains 1200 square miles and the center of the area is at Dover, 40 miles west of New York City. In the general area are found 18 parallel ranges or lines of ore deposits. These ranges may be re-garded as mineralized zones in which occur orebodies that are rich enough in magnetite to war-rant mining. Usually a number of the orebodies lie one above the other in the same plane, all dipping and pitching in the same direction. Within the ranges, there may be several parallel orebodies of work-able size. The average strike of the orebodies is N.41° 30' E., with an average dip of 55° southeast and an average pitch of 15 ° to the northeast. Orebodies suitable for mining range from 6 to 100 ft. wide, as measured from foot wall to hanging wall. Their heights, as measured on the dip and normal to the long axis of the orebody, vary from 200 to 3,000 ft. The length along the pitch has never been determined by mining, al-though several of the orebodies have been worked to lengths of 10,000 ft. The grade of the ore as mined today varies from 30 to 60 per cent iron, and the gangue min-erals are chiefly silica, alumina, magnesia, lime and phosphorus.

Jan 1, 1937

By William Kelly

THE objeet of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the result's of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912.

Jan 2, 1914

By Finney, W. R.

MUCH has been said and written of the "Big Inch," of the terrific obstacles encountered in its construction, of the colorful and tough men engaged in its building, but little has been publicized of the engineering and economic problems behind the scenes. Long before Pearl Harbor it was apparent to the petroleum industry that a critical oil shortage could be expected along the Atlantic seaboard, owing to delay in tanker deliveries as a result of convoy movements, and to allocation of vessels for foreign shipments. This area, with a normal consumption of approximately 1,800,000 barrels per day of oil and products, was almost entirely supplied by tanker. Pipe lines supplied an average of only 20,000 barrels per day in 1939, 40,300 barrels per day in 1940, and 55,000 barrels per day in 1941. A small amount of oil and products was also delivered via barge.

Jan 1, 1943

By K. L. Moazed, G. M. Pound

An investigation was made of the deposition of silver from a thermal beam onto tungsten field-emitter tips at 300°K. "Island"-type nuclei were observed to form and grow. The nucleation of silver crystals occurs preferentially on non-close -packed planes of a tungsten tip at a critical volume free-energy change of about —2900 cal per cc. The adatom population which is critical for appreciable nucleation rate of silver crystals is about 0.2 of a monolayer and is essentially independent of beam flux, time, and source temperature. This result is strong evidence that a metastable equilibrium exists between adatoms and critical nuclei, as assumed in the present theory. SOME of the more significant studies of nucleation in deposition of metals from vapor beams have been conducted by measuring the thermal beam flux which is critical for appreciable rate of nucleation on a substrate surface held at a given temperature.'2 The observed critical supersaturations may be described in terms of Eq. [7] which was derived3'3a on the model of an adsorption, surface migration, and statistical fluctuation mechanism. However there usually made with a low-power optical microscope, a fairly insensitive method of detection. The object of the present study was to overcome some of these difficulties by measuring the critical supersaturation for condensation of a thermal beam of silver onto a tungsten field-emitter tip. Such a tip may be cleaned by electrically heating it to a high temperature in situ, and the high vacuum obtainable in a field-emission tube (10-10 torr) precludes adsorption of residual gases for convenient periods of time. Furthermore, the degree of cleanliness, the orientation, and the state of imperfection of the tip may be ascertained from the field-emission pattern. Detailed explanations of theoretical considerations and experimental procedures relating to the field-emission microscope may be found in a number of excellent review articles12'13 and thus only a brief description will be given here. The electronic work function of a metal is defined as the energy that an electron needs to escape from the potential field of the solid. By applying a large field between the surface of the solid and a suitable collector, it is possible to free the electrons by the tunnel effect. Fields of approximately 30 million v per cm are needed to produce this effect, and such fields are obtained in practice by using microscopic surfaces of high curvature (tips). Because the work function of a metal is a function of surface orientation, the emission from the various planes is different, and thus it is possible to obtain a representation of the surface in the emission microscope. In general, the work function is higher for the more densely packed planes. Fig. 1 shows a pattern for "clean" tungsten in which the central dark region represents the (110)

Jan 1, 1964

By Noah Fields Drake

This paper is devoted chiefly to the coal-fields of the western part of the province of Chili and the eastern part of the province of Shansi; but the outline of this belt will give some idea of the extension of the coal-fields over northeastern China. This part of China is topographically divided into: (1) the mountainous peninsula of eastern Shantung; (2) the coastal plains, extending W. and SW. from the gulf of Pechili; and (3) the mountains and table-lands N. and W. of the coastal plains. The plains extend N. and W. from the gulf to within from 10 to 25 miles of the Great Wall, while their SW. extension covers western Shantung and reaches W. along the Yellow river almost to the southern boundary of Shansi. A line joining the mapped coal-fields, shown in Fig. 1, almost gives the western boundary of the plains; since these areas lie on the border of the plains—except the Tsê Chou field, which is on the table-land, 20 to 25 miles from that border. The coal-fields which have been mapped and investigated by the author are shown in Fig. 1. The one at and around Tongshan is known as the K'ai-p'ing coal-field; the one W. of Peking has been called the Wang-p'ing coal-basin; the one SW. of Pao-ting and N. of Chêng-ting may be called the Lingshan coal-field; and the one at and around Tsê Chou is known as the Tsê Chou coal-field. I. The K'ai-p'ing Coal-Field. As is shown in Fig. 2, most of this field lies in the coastal plains, and is therefore covered by alluvium and loess, which have buried the older rock-beds, and the more gentle and older topographic outlines, to such an extent that most of the re-

Jan 1, 1902

By HAROLD A. TITCOMB

TOWARD the close of 1925, a British geologist, T. Landell Mills, brought to the notice of .A. Chester Beatty and selection Trust Ltd. certain mineral areas in southern Yugoslavia. Mills' data, which included rough maps and preliminary reports by' a Yugoslav engineer, Jules Draskocy, appeared interesting to Reatty, and early in 1926, I, with three British assistants, proceeded to Serbiaand commenced the investigation of several groups of ancient mine workings. They were found to be extensive and the geological conditions-schists, limestones, and andesitic intrusive-favorable for mineral deposits. At Stan Trg, on the Trepca Concession, five rniles east of Kosovska Mitrovica, an ancient filled adit was found, a shelter-hut erected, and work started in reopening this adit.

Jan 1, 1936

The phosphate pebble-bearing matrix in the Florida Phosphate Pebble Field has physical properties which make it readily adaptable to hydraulic transportation methods employing solids-handling pumps and pipelines. The abundance of water available, a practically flat terrain, low costs per ton-mile, and beneficiation of the matrix by agitation while being pumped have contributed to the popular choice of hydraulic transportation. Phosphate pebble mining in Florida, begun in the 1860's, first used high pressure water and solids-handling pumps for overburden removal about 1900. Removal of the average 25 ft of overburden was followed by hydraulic mining of the matrix, with 6-in. and 8-in. pumps handling 50 to 100 cu yds per hour being moved along the floor of the pit as they were advanced toward the face being undercut and slurried by hydraulic guns.

Jan 3, 1961

By T. E. Scott, O. G. Koepke

DURING research currently in progress the need arose for interplanar angles and planar spacings to analyze crystallographic data obtained from hcp yttrium. In the absence of such existing information, a program was written in Fortran-11 language and processed on an IBM 7074 computer. The program and results have been assembled in report form to make them generally available.' Of the possible combinations of, only those most frequently encountered were employed. The ranges of h, k, and 1 involved were: However, not all combinations and permutations of the above appear in the tabulation because redundancies occur in several cases. Nevertheless, fifteen types of planes and all their equivalent planes have been included, giving a total of 109 sets of Miller-Bravais indices.

Jan 1, 1967

By P. H. Mell

The little village, from which this formation receives its name, is situated on a bluff of the Alabama River, 175 feet above water level. This bluff is a portion of high table land that begins in the western portion of Choctaw and extends through Clarke and Monroe counties. We find points on this ridge more than 100 feet higher than Tuscaloosa, and nearly as high as the Tennessee River at Tuscumbia. Through this the Alabama River cuts its way, exposing a beautiful cross-section of the strata, of which the accompanying sketch may give some idea. The fossils are found about 75 feet below the surface and 100 feet above the level of the river. There are seven distinct strata. 1. The lowest, extending from the water's edge up the bluff 80 feet, is a soft calcareous rock containing about 15 per cent. of carbonate of lime, with occasional specks of mica. In this a few Ostrea, Turritellæ, and Flustræ were found, but so friable as to fall to pieces when handled. 2. Next comes a stratum varying from 2 to 8 feet, consisting of

Jan 1, 1880

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By D. B. Robinson, J. Lukacs

A knowledge of the equilibrium water content of hydrocarbon systems under pressure is important to the natural gas industry. The information available on the solubility of water in hydrocarbon, hydrogen sulfide, and carbon dioxide systems is reviewed in this paper and the influence of the more important variables such as temperature, pressure and molecular structure on solubility in liquids and gases is discussed. A suitable cbromatographic technique has been developed for determining low concentrations of water. Tailing of the water peaks has been elim inated by adding water to the carrier gas stream The method is applicable for both gas or liquid samples and is effective in the presence of hydrogen sulfide. The experimental study of water solubility in methane-hydrogen sulfide systems at a temperature of 16oF has shown that the presence of hydrogen sulfide causes only a modest increase in water content at pressures up to 1,400 psia. Theoretical considerations and data on pure hydrogen sulfide and carbon dioxide suggest that the effect of both these compounds will be greater at higher pressures and in the liquid phase. INTRODUCTION Before transporting or processing natural gases and gas condensates, it is usually necessary to dry them using suitable dehydration equipment. The design and operation of this equipment requires a knowledge of the amount of water present in the fluid at the reservoir and operating conditions. This is influenced by temperature, pressure and composition, particular1y when certain non-hydrocarbon components are present. Field experience indicates that hydrogen sulfide and carbon dioxide, for example, alter the usual water solubility relationships appreciably. However, an extensive search of the literature does not reveal any quantitative data on such systems. For sweet natural gases, generalized empirical correlations such as the one proposed by Katz, et al,6 can be used to predict water solubility with confidence at most temperatures and pressures of interest. However, existing theoretical relationships do not permit a calculation of the deviation from these curves when polar substances like hydrogen sulfide are present in the system. Thus one must resort to an experimental approach to obtain the necessary information. The fact that laboratory experimental methods frequently involve the use of mercury which reacts with hydrogen sulfide in the presence of water, and that hydrogen sulfide interferes with many chemical reactions specific for water has contributed to the difficulty of studying water solubility in systems containing hydrogen sulfide. In this investigation the water content of a limited member of methane-hydrogen sulfide mixtures was determined using a special technique with gas chromatography. REVIEW OF PUBLISHED DATA Experimentally determined water solubility data have been reported for methane, 14 ethane, 15 propane, 9 n-butane, 16 1-butene, 11 hydrogen sulfide 18 and carbon dioxide. 19 These studies report the effect of pressure, temperature and molecular structure on water solubility in single component gases and liquids. Fig. 1 compares experimentally determined water solubilities in several hydrocarbons, carbon dioxide and hydrogen sulfide at l00F as taken from this

By Louis Katona

The practical execution of the design for rolling-mills presented by the writer at the Paris meeting* of thc Iron and Steel Institute in 1900 involves the determination of some questions not yet discussed, among which is the determinatioir of the amount of power required to perform the rolling of pieces of iron and steel of given dimensions. It is necessary to know this factor if we would put motors of proper capacity to the respective pairs of rolls, or, rcciprocally, if, having standard motors at our disposal, we would design grooves to suit them. Moreover, this factor is involved in giving right dimensions to every part of the rolls and housings. Expert designers of engines for driving rolling-mills of the present type receive very indefinite directions, such as: that the motor is to drive a light, medium or heavy train; that it must work with fly-wheel or reversing gear; that the number of revolutions per minute should not exceed 40 or 60, and that at a given speed the power developed should be from 100 to 200 H. P., or from 1,000 to 2,500 13. P. It frequently happens, however, that an cngine of 200 H. P. is forced under the circumstances to press or develop as much as 300 H. P., while, on the other hand, the ,1,500-11. P. engine may be rolling-stock which could be worked with a maximum expenditure of 60 to 80 H. P. Of course such variatior~s as these do not permit the best adjustment of parts or the best economy of power and fuel. The design of roll-trains is even more vaguely limited. Every part of a train, from the point where it connects with the engine to the last groove in the rolls, bears evidence that there are no rules for calculating even approximately the dimensions of the main-shafts, couplings, pinions, gears, rolls, trunnions,

Jan 1, 1904

By C. L. Pillar

INTRODUCTION The location, size, character of the ore de- posit and its adjacent formations will deter- mine the mining system best used for its ex- traction. The mining system chosen will have to be engineered to suit the ore deposit and the people that will extract it. What can be done in the Philippines cannot always be accomplished in the upper Northwest Territory of Canada. Mining operations developed under a free enterprise system are planned to achieve a satisfactory return on the capital required to place them into production. Hence, the choices made in planning and developing the mining system must be dictated by sound economics. The mining system planned must favor: 1. Maximum ore extraction of the deposit with minimal grade dilution. 2. The amount of capital expenditure used to develop and equip the mine must be in harmony with the financial policy of the group yet be sufficient to provide a reliable mining system. Excessive frills and extras that are not required for efficient, safe production should not be provided. 3. Mine production costs are determined by the amount of men, material, equipment and energy used in the production process. These must be kept to minimal limits in order to insure dependable, low cost production. Extras that later are needed in the production operation can be added as required by the operator. Basically block caving is a mining system that is normally used to extract deep seated, massive, low grade deposits of copper, molybdenum and iron where stripping ratios for open cast mining are economically prohibited. The caving system is limited in its selectivity. It is a mass production type of underground ore extraction that under favorable conditions is one of the most efficient, low cost mining systems in the world today. Usually block cave mining systems are large. They are capable of producing ore at a rate of 10,000 to 100,000 tons/day from large deposits at costs that are comparable with many open cast mining systems burdened by high waste to ore ratios. Block cave mining systems differ basically in the plan of the area layout, the method of undercutting and the method of draw. The balance of the mining system is the mechanical transportation of the drawn ore to the surface, the mine supply, drainage and ventilation systems. This paper deals mainly with the methods of draw. The method of draw to be used in a block caving system dictates the development plan of the mining area, is highly influential in the method of undercutting to be employed and the supply and ventilation system to be used. There are three basic methods of draw commonly used in today's operations. They are: Gravity draw Slusher draw LHD draw The type of draw planned will have a major affect on: Capital expenditure and time required to bring a deposit into production. Productivity, efficiency and cost of the production operation. Percent recovery of the ore deposit in both tonnage and grade. Degree of production reliability Fundamentally the type-of draw used must be compatible with the physical characteristics of the deposit to be extracted and the financial position of the mining operation. The type of draw chosen must work to advantage with the size, configuration, depth, strength and fracture pattern of the deposit and its adjacent formations. It must favor the financial protection of the planned mining operation. A Gravity Method of Draw requires a finely fragmented, easy flowing product from the caving action of the deposit. To obtain the desired economic advantage the ore deposit must also have sufficient area and height of column to permit minimal development cost on a per ton basis. The gravity system re- quires the maximum amount of development openings and uses the minimum amount of mechanized equipment of all the caving systems. It is unskilled, labor-intensive and is highly sensitive to size of ore fragmen-

Jan 1, 1981

By P. H. Dudley

I have taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of 'our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that,, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its econonlical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 941/2 miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 footpounds, exclusive of the force to move the locomotive itself. We

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geo- physics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining.

Jan 1, 1949

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-'100' crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By C. G. Durdaller, W. H. Robinson, G. M. Pound

The nucleation rate of the a (pay) to 0 (white) tin transformation was measured as a function of temperature and a tin particle size using an X-ray diffraction technique. The powder specimens of a tin were essentially monodisperse and the small dinzension of the particles of these specimens was varied from 13 to 75 p. Several types of nucleation sites of differing potency were fbund to be operative in the nucleation process, but it could not be determined whether these sites were on the free surface of the tin particles or within the volume. Assuming that they were on the free surface, the average density of the most potent sites was calculated to be 2.5 to 5.3 x 10' sites per sq cnz through the application of a Poisson distribztion finction to the isothermal data. Analysis of the temperature dependence' of the rate constmts at a given fraction transformed suggests that the active sites are regions of higher free energy and not catalytic interfaces. Appreciable induction periods were observed at the lower temperatures of transformation. Experimental studies1 of solid-solid phase transformations have led to the belief that the new phase nucleates at structural imperfections. The purpose of the present work was to learn more about the mechanism of nucleation in solids and the nature of the singularities at which nucleation occurs. In this investigation nucleation rates in the isothermal transformation of gray to white tin were measured by an X-ray diffraction technique using essentially monodisperse powders of gray tin. This particular phase transformation was chosen for study because it presented fewer experimental difficulties than most others. The experimental temperature-control problems were minimal because the two phases coexist in equilibrium at 13.3"C, and measurable transformation rates occur at temperatures only slightly above room temperature. The growth rate of the P phase into the a2 is sufficiently fast to make the measured transformation rate equivalent to the nucleation rate, provided that the particle size of the samples is small enough; for the experimental temperatures used in this study, the particle diameter must be less than 100 p. EXPERIMENTAL TECHNIQUE The P tin used in this study was obtained from Capper Pass and Son Ltd., North Ferriby, Yorkshire, England, and was of 99.999 pct purity. It was transformedS to the a phase and ground into a fine powder in an agate mortar. This powder was separated by a Roller air classifier into seven fractions whose dimensions, as determined by microscopic measurement of many thousands of particles, are given in Table I and whose distribution of size within each fraction is given in Figs. 1 and 2. The shape of the particles was roughly that of an oblate spheroid,

Jan 1, 1964

By John F. Myers

Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity.

Jan 8, 1958

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927