Search Documents

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By A. C. Fieldner, Lester L. Hirst, Henry H. Storch

Experimental work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogehation of bituminous coal and tar by the Bergius-I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 Ib. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydro-genation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. Equipment and General Procedure of Research The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By Lester L. Hirst, Henry H. Storch, A. C. Fieldner

Experimental work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogehation of bituminous coal and tar by the Bergius-I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 Ib. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydro-genation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. Equipment and General Procedure of Research The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

[ ]

Jan 1, 1938

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By M. C. Udy, P. C. Rosenthal

THE use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace, The present study presents the results of a systematic survey of. the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels, Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. EXPERIMENTAL WORK Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. [ ] Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions . was prepared with boron additions in amounts of 0.0015, 0.003, and o,006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two com¬mercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120, Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel scrap were used for melting stock. Deoxidation was carried out in the furnace with o.10 per cent aluminum. The aluminum addition was

Jan 1, 1946

By Dudley L. Davis, E. C. Peterson

INTRODUCTION THE Darwin District is 30 miles east of Olancha which is 220 miles north from Los Angeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin Plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacement of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were discovered in the early seventies. By 1875, Darwin had a population of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation of metal prices caused intermittent operations until World War II. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. For the past two years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 pct of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. GENERAL GEOLOGY The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably Pennsylvanian in age. These rocks have been intruded on the west by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills. The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 95°W, dips steeply south and is traceable for about 1o miles. It is a normal

Jan 1, 1947

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps. The area covered in this study is shown in Fig. 1 on which are indicated the relative location and approximate outlines of the principal producing camps. This also shows the approximate yield to date of each major camp in terms of combined lead and zinc concentrates. The output of zinc concentrates is roughly seven times that of lead. Hence, the economy of the district has depended primarily on the price of zinc, with lead as an important byproduct. Over much of the productive period, lead concentrates averaged about twice the value of zinc concentrates per ton, and in certain mines or areas the proportion of lead to zinc was substantially above average. The Joplin district is largely flat prairie but is partly moderately dissected, partially wooded land with a relief generally less than 100 ft. The rocks are almost flat-lying, nearly parallel to the surface, and the chief ore formation is the Mississippian Boone limestone, including its cherty phases. This formation either outcrops in the producing areas or is covered by a thin veneer of Pennsylvanian shales. Virtually all the ore occurs within 400 ft of the surface, and a large part at less than 300 ft in depth. Most of the land was divided into small farms or town lots before mineral development; tracts seldom exceeded 160 acres, and averaged considerably less. Mineral rights followed the surface ownership, segregation was rare, and a system of leasing for mineral development became well established early in the region's history, many landowners deriving small to sizable fortunes from royalties. Because of the shal-lowness of the ore and other factors, prospecting and mining was cheaper than in almost any comparable mining district in the United States. This situation, coupled with the widely divided land ownership, offered a fertile field for promoters and speculators and led to the rise of many small mining concerns. Only in its later history, under stern economic compulsion, has control tended to centralize in a few companies. Under these conditions, any important new discovery or successful development had much the effect of a gold rush or an oil boom. Every property in the area was leased quickly, promptly drilled, and, if ore was found, it was soon on the market. Many companies and individuals participated, and the average producing lease-hold probably was about 40 acres in extent. Any important field thus was attacked by anywhere from 10 to 100 or more producers. Production zoomed, eventually steadied or wavered, and ultimately subsided, leaving a desolation of tailings mountains, cave-ins, empty housing, and wreckage. The object of this paper is to depict the pattern of this process, so far as metal production is concerned, and to note the way in which it reacted to economic and political pressures. Production Charts In Fig. 2 is charted the production record, in tons of lead and zinc concentrates combined, of eight of the principal camps, which together account for approximately 99 pct of the total district production, over the years from 1870 to 1950. This period covers all but the very minor beginning of mining history. Two important camps are divided by state lines; hence, it has been necessary to combine production records for the two portions, based on estimates that may be slightly in error. Certain camps are sub-dividable into important units for which separate figures are available in whole or in part and have been charted as fractions of the major unit. The corresponding price of zinc is shown above all the charts. Three camps, Aurora, Neck City, and Galena, show a remarkably symmetrical graphic pattern, which is interpreted as the norm. The curves rise steeply to a peak, level off for an irregular interval, and then drop sharply to zero on a slope corresponding roughly to that covered by the initial rise. The three portions of these charts seem appropriately characterized by the designations of youth, maturity, and decline. On the whole, with some irregularities, the production in each of the three periods seems to be almost equal. A fourth camp, Granby, fails to conform to the normal pattern. It exhibits a very long period of reasonably uniform, stabilized production corresponding to maturity, followed by a rather precipitate decline. Its youth is hidden in the era of prehistory. This habit of steady, long-continued production at an even keel is attributable to the fact that this camp, more than any other, was controlled largely by a single principal owner at any given period over most of its history and this permitted the imposition

Jan 1, 1952

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By Arthur Zentner

THE essentials of the electrolytic zinc process, as now used in commercial plants, date back to work done by Letrange in 1881. He used sulfuric acid to leach roasted sulfide and ,oxide ores, purified his solution very much as we do now, and electrolyzed the purified zinc sulfate solution. Ten years later Hoepfner developed a process using chloride solutions, and built three plants. One in England operated until 1924 in one of the works now merged in the Imperial Chemical , Industries, Ltd. Ashcroft built a plant in 1898 in the Broken Hill district of Australia. He used both chloride and sulfate solutions.. While his work failed, the aid his published results have been to later workers has made him an outstanding contributor to the de- velopment of the electrolytic zinc process. A good deal of work was done in the following years, aiming to electrolyze zinc chloride solutions and fused zinc chloride. Quite a bit of work on sulfate solutions was also done in the last years before the war. With the outbreak of the war, metal demand and rise in metal prices provided the stimulus which resulted in the remarkably rapid commercial development of electrolytic zinc. In this last period of development, all the work brought to commercial fruition has been with sulfate solutions. The high-density process, or the Tainton process, is used, as you know, in the Sullivan electrolytic zinc plant at Kellogg, Idaho, and will be used in the Evans- Wallower plant now being built at East St. Louis. The low-density process is used by the other plants now operating in the United States and other countries. There are now in operation and under construction four electrolytic zinc plants in the United States, two in Canada, two in Italy and one each in Australia, Rhodesia, Poland, Norway and Germany.

Jan 1, 1929

By Robert Glass Cleland

[George B. Agnew Cleveland H. Dodge James Douglas E. Hayward Ferry Francis L. Hine Arthur Curtiss James1908-1941 1908-1926 1908-1918 1908-1935 1908-1927 1908-1941]

Jan 1, 1952

In traversing lately the Sierra Madre, west of Sail Pedro and Guanacevi, I estimated the topographic summit at several points, by aneroid barometer, at about 8,500 ft. Mr. Weed's measurements, 40 miles further north, are from 9,000 to 9,500 ft., and indicate the correctness of the impression I obtained at the time, namely, that the greatest movement in the elevation of the Sierra was between Guanacevi and Guadaloupe y Calvo. This is suggested also by the course of the headwaters of the Rio Conchas and of the Nazas, and by the relative corrasion of the branches of the two streams. Mr. Weed's statements as to the unevenness and great relief of the andesite floor underlying the later dacites and rhyolites are very interesting, and lead me to add that the floor of the andesite breccias and flows is uncovered for several square miles east of Guanacevi. This floor is of reddish, bluish and gray shales, lying horizontal or dipping slightly east. Their age is unknown; but from the interbedded occurrence of copper sulphides, I took it to be Triassic,

Jan 1, 1903

By Donald H. McLauqhlin

ITEM expressed in billions of dollars have become so commonplace these day- that a mere statement of the latest figures for the country s gold reserve scarcely conveys m adequate sense of the immensity of the commitment the nation has made in building up its huge stock, two-thirds of which is now stored at Fort Knox. Kentucky. Only by measuring it against quantities that mean something tangible to a particular group can an adequate comprehension of its magnitude he rained; consequently, to mining engineers, a comparison with the value of output from well-known mining districts might best serve to give some degree of reality to the astronomical figure at which the country gold is now valued.

Jan 1, 1941

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric's Compax® and Stratapax® and Megadiamond's Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973