Search Documents

World Petroleum Consumption. By V. R. GARFIAS AND R. V. WHETSEL. (Trans, vol 107). A tabulation showing world consumption of gasoline, kerosene, gas and fuel oil, lubricants, and miscellaneous petroleum products by counties in the years 1931, 1932 and 1933 , Totals are given; for instance, Cuba consumed 3,998,000 bbl of all petroleum products in 1933, in 1933; the world consumed 1,366,291,000 bbl. of all petroleum products, etc. Domestic Production. Annual Symposium of Petroleum Division, February Meeting, 1934 (Trans, vol. 107. 181 pages.) The symposium consists of reports on petroleum and gas developments and production in the producing states of the United States. This year the statistical information is presented in a new and far more comprehensive form. The reports on domestic production are as follows: Arkansas, by B C Craft; California, by V H. Wilhelm and H. W. Miller, Colorado, by C. E. Shoenfelt, Illinois, by A H Bell, Indiana, by W. N Logan and P. Simpson; Kansas, by Marvin Lee; Kentucky, Ohio and West Virginia, by V. C Smith; Louisi¬ana, by B C Craft, Michigan, by Theron Wasson; Mississippi, by B C Craft; Missouri, by F C Greene, Montana, by H. N Hickey, New Mexico, by C. E Shoen¬felt and D E Winchester, New York, by D. H. Newland, Oklahoma, by L. G. E. Bignell, J 0 Lewis and E. A Hanson, Pennsylvania, by G H Fancher, Tennessee, by L. C Glenn, Central Texas, by R B. Kelly and P R Martin, East Texas, by A R. Denison, Gulf Coast, by L P Teas, North Texas, by H B Fuqua and B. E Thomp¬son; North Central Texas, by J M. Armstrong, Panhandle, by R H Lynn and T. C. Craig, Southwest Texas, by 0. G. Bell; West Texas, by C W. Reith, Utah, by E S Shaw, Wyoming, by J G Bartram.

Jan 1, 1935

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By E. R. Gilbert, D. E. Munson

Creep of copper under 75 to 1.50 kg per sq cm stresses at temperatures near the melting point was found to he a complex reaction controlled by three mechanisms acting in parallel. In order of appearance with decreasing temperature, the auerage activation energies, Qc , are 168, 79, and 24 kcal per mole. Stress dependence of the minimum creep rate was found to he an exponential for the two high-Qc processes and a power law for the low-Qc, process. Transition of control occurs from one mechanism to another. The relative transition temperature depends upon the applied stress, and the range oiler which the transition occurs depends upon the difference in the activation energies of the mechanisms. The creep behavior at high temperature is explained by the climb of dislocations through thermally or mechanically formed jogs, CREEP in pure fcc metals at temperatures in excess of one half the absolute melting point is normally controlled by dislocation c1imb.1,2 A climb model which seems applicable, according to an extensive analysis of data,3 was derived by Weert-man.4 This model assumes jog-saturated dislocations and predicts an activation energy, Qc, nearly equal to that for self-diffusion, USd. Although the requirement of jog saturation is restrictive, agreement between theory and experiment seems adequate. Many other theoretical treatments, including an early model by Mott,5 include detailed consideration of jog formation as an initial requirement for climb. These models predict activation energies for creep which differ from those of self-diffusion. Seeger6,7 postulates an observed activation energy related to the stacking-fault energy. Thus, Usd <Qc<5Usd + Uj where Uj is the jog-formation energy. Seeger incorporated qualitatively the influence of the relative numbers of thermal and athermal jogs. Expanding this concept, Shoeck8 explicitly states a function based on formation mode and relative numbers of vacancies: e r ci exp {-uf/k T} exp {-Um/k T} [ 1 ] where Uf and Um are energies of vacancy formation and migration, respectively. The concentration of jogs, Cj, depends upon the manner of jog production. For intersection jogs, Cj is not sensitive E. R. GILBERT, Junior Member AIME, formerly with De- to temperature; for thermal jogs, Cj is proportional to exp {—Uj /k T}. Schoeck regards each mode as a distinct mechanism; therefore, the mechanisms may act together.299 The diversity predicted by theory, surprisingly, has not been substantiated by experimental results. A significant investigation must include the extremes in stacking-fault energy. Extensive creep studies of aluminum10 and nickel,11,12 high stacking-fault energy metals, have been made. Comparable studies on a low stacking-fault energy metal, such as copper, have not. It is the purpose of this paper to report the results of an investigation of the creep of copper under conditions which favor thermal jogs. EXPERIMENTAL Cylindrical compression creep specimens (0.240 in. in diameter by 0.400 in. long) were machined from cold-drawn rods of electrolytic tough-pitch copper containing 0.0007 Mg, 0.002 Fe, 0.001 Ni, 0.0005 Ag, Cd < 0.005, and Pb < 0.005 wt pct impurities. Undetected spectrographically was a nominal 0.04 wt pct 0, which occurs as a Cu2O constituent distributed discontinuously at grain boundaries. Vacuum annealing at 900°C for 15 min produced a stable 0.03-mm average grain diameter. Testing was carried out using apparatus similar to that described by sherby,13 modified by enclosing platens and a push rod in a vacuum cylinder. Normally this arrangement resulted in pressures less than 10 Only a slight surface tarnish, less than 0.0005 in. in thickness, occurred during the test. The applied stress, corrected for atmospheric pressure, was maintained within 2 pct of the desired true stress by the addition of lead shot at fixed strain increments. Creep strain was measured with dial gages as a relative displacement of the upper and lower platens; accuracy of measurement was 0.0001 in. Two creep-test methods were used, the differential or cyclic temperature14 and the isothermal, to obtain creep data at stress levels of 150, 100, and 75 kg per sq cm over the temperature range of 620° to 1032°C. Minimum creep rates were used from both test methods; this was considered proper because comparable temperature tests or cycling to the same temperature gave the same creep rate, within experimental error. The cold vacuum test chamber, with the unstressed specimen in place, was heated to temperature by placing a preheated furnace over the chamber. Temperature equilibrium was attained within 30 min. For the cyclic tests, the stress was removed during the 5 to 10 min necessary to effect the temperature change and re-

Jan 1, 1965

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler&apos;) have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,&apos; concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina&apos; crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40&apos; to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33&apos; to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5&apos; A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6&apos;F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40&apos; to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33&apos; to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5&apos; A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6&apos;F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By Persifor Frazer

The rocks which cover the east flank of the South Mountain are chloritic schists typical in character. A specimen of this rock from near the Bechtel shaft, Hamilton Ban Township, Adams County, Pa., was selected and analyzed in my laboratory by Mr. C. Hanford Henderson, with the following results: Ignition,........2.740 CaO,..........7.040 SiO,,..........41.280 MgO,.......... 7.486 AI,O,,.........18.480 K,O,..........2.208 Fe,Os,.........9.440 Na,O,.........3.523 FeO,......... 8.200 100. As one penetrates the range by moving westvard, these schists are replaced either by epidotie quartz or by orthofelsite. In the former case, a belt of copper-bearing rock is traversed, but not in the latter case. Inasmuch as this junction of the chloritic schists on the southeast and orthofelsite on the northwest, separated by the epidotic quartz, is several times repeated, we find two or three copper belts arranged in general parallelism to the axis of the chain, because the copper horizon is generally at this junction. Thus, in going west from Fairfield, after entering the low spurs on the South Mountain, one is fairly within the chlorite measures. At the " Virginia Mills " a chlorite schist comes in with a dip of S. 1.5 E.-74 Half a mile up Middle Creek, large numbers of fragments of chlorite schist, decoruposed epidotic matter, and quartz are encountered. The former rock, where in place, dips E. 40" S.-57o. About 4000 feet west of the intersection of this road with the so-called Tape-Worm Railroad, near the house of one Singly, large masses of chloritie schist are found loose on the road. A hundred yards farther west, near a triangle in the road, the latter is less in quantity and much epidotic quartz appears, after which a very large display of orthofelsite succeeds on the left bank of Middle Creek. All these last-mentioned rocks, however, are in fragments. Crossing the stream again a few hundred yards farther On, the chlorite fragments at first preponderate, and then large numbers of both rocks

Jan 1, 1884

By P. M. Robinson, M. B. Bever

THE heats of formation at 273°K of the compounds InBi, In2Bi, and TIBi2 have been determined by metal solution calorimetry with bismuth as solvent. The published information on the thermody-namic properties of these compounds is limited. The structure of the compound InBi (mp, 383°K) is tetragonal of the PbO (B10) type.1 The compounds In2Bi (mp, 362°K) and TIBi2 (mp of highest-melting composition, 486°K) are now believed to have structures of the NizIn (B8) type273 and not the A1B2 (C32) structures reported earlier.4, 5 The compounds In2Bi and TIBi2 have limited homogeneity ranges at room temperature, while the compound InBi has no detectable homogeneity range.&apos; Samples of the compounds were prepared from 99.99 pet Bi (Mallinckrodt Chemical Works), 99.999 pet in (American Smelting and Refining Co.), and 99.99 pet Tl (Amend Drug and Chemical Co.) by melting the components in sealed, evacuated Vycor tubes. The compounds InBi and in2Bi were of the stoichiometric compositions. The compound TIBi2 contained 40 pet T1; this composition was chosen because at room temperature the alloy of stoichiometric composition does not lie within the homogeneity range.&apos; The melts were held approximately 50°C above the liquidus for 8 hr and then quenched into iced brine. The samples were homogenized for 48 hr at temperatures 20°C below the temperature of complete solidification. Metallographic examination of sections taken from the center and the ends of the ingots did not reveal second phases or segregation . The heats of formation were determined as the difference in the heat effects on solution of a compound and of a mechanical mixture of its components added from the reference temperature of 273°K to liquid bismuth at 623°K. The details of the calori-metric procedure and method of calculation have been described elsewhere? The calorimeter was calibrated by adding bismuth at 273°K to the bismuth bath at 623°K. The calculated values of the heats of formation of the compounds, listed in Table I, are based on a value of 4.96 keal per g-atom for the difference between the heat contents of bismuth at 273" and 623oK7 No published values are available for the heats of formation of the compounds InBi and In2Bi. Hultgren et a1.7 have calculated a value of -0.50 i 0.10 keal per g-atom for the heat of formation at 423°K of the compound TIBi2 containing 40 at. pet T1 from heat-content measurements in the range from 398" to 700°K and the heats of formation of the liquid alloy. The difference between this value and the value of -0.66 * 0.01 keal per g-atom at 273°K is too large to be attributed to a difference between the heat capacities of the compound and the components over the temperature range 273o to 423oK7 However, the direct determination of the heat of formation by a calorimetric method should give a more accurate value. The heats of formation at 273°K of the compounds InBi and In2Bi lie on a straight line when plotted as a function of composition, Fig. 1. The compound In2Bi, therefore, appears to be barely stable with respect to its neighboring phases. In order for the free energy vs composition curve to be concave towards the composition axis, the entropy change on formation of In2Bi must be more positive than that on formation of InBi. As the compounds are ordered,2, 3, 8 there is no configurational entropy change on formation. The difference between the entropy changes on formation of the two compounds, therefore, is probably associated with the vibrational entropies. In view of the low heats of formation, the changes in vibrational entropy, due to changes in bond strength on formation of the two compounds, are likely to be small. Owing to the volume contractions on formation of the two compounds,5 the vibrational entropies probably decrease slightly but the decrease of the vibrational entropy of InBi is expected to be larger than that of In2Bi.

Jan 1, 1965

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,&apos; it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

[ PRESIDENTS DAVID THOMAS 1871 &apos;R. W. RAYMOND 1872-1874 &apos;A L. HOLLEY 1875 &apos;ABRAM S. HEWITT 1876 &apos;T. STERRY HUNT 1877 &apos;ECKLEY B. COXE 1878-1879 &apos;WILLIAM P. SHINNY 1880 &apos;WILLIAM METCALF 1881 &apos;RICHARD P. ROTHWELL 1882 &apos;ROBERT W. HUNT 1883 &apos;JAMES C. BAYLES 1884-1885 ROBERT H. RICHARDS 1886 &apos;THOMAS EGLESTON 1887 &apos;WILLIAM B. POTTER 1888 &apos;RICHARD PEARCE 1889 &apos;ABRAM S. HEWITT 1890 &apos;JOHN BIRKINBINE 1891-1892 &apos;H. M. Hows 1893 &apos;JOHN FRITZ 1894 &apos;J. D. WEEKS 1895 &apos;E. G. SPILSBURY 1896 &apos;THOMAS M. DROWN 1897 &apos;CHARLES KIRCHHOFF 1898 &apos;JAMES DOUGLAS 1899-1900 &apos;E. E. OLCOTT 1901-1902 &apos;ALBERT R. LEDOUX 1903 &apos;JAMES GAYLEY 1904-1905 &apos;ROBERT W. HUNT 1906 &apos;JOHN HAYS HAMMOND 1907-1908 &apos;D. W. BRUNTON 1909-1910 &apos;CHARLES KIRCHHOFF 1911]

Jan 1, 1940

Extractive Metallurgy Division Institute of Metals Division Iron and Steel Division Council R R McNaughton, Chairman (EMD), Ernest O Kirkendall, Secretary, J H Scaff, (IMD), Morris Cohen, (IMD), T J McLoughlin, (ISD), J S Marsh, (ISD), P T Stroup, (EMD), R D Parks, (MED), D S Eppelsheimer, (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, T D Jones, Evan Just, J C Kinnear, Jr, J S Marsh, M Tenenbaum Pacific Northwest Regional Meeting F X Cappa, General Chairman, W W Wiltschko, Chairman (Metals Branch), Program Chairmen H E Lee (EMD), S E Maddigan (IMD), G R Heffernan (ISD), L C Richards (Ind Min Div), James Bell (Finance Committee), Ed Vestica (Registration), Donald Johnson (Special Events)

Jan 1, 1954

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer&apos;s immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author&apos;s preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer&apos;s interpretations are suggested.

Jan 1, 1929

By R. Stickler, A. Vinckier

An optical and electron microscope study was made on a commercial 302 stainless steel heat treated for massive carbide precipitation. Convincirg evidence was obtained that the grain boundary precipitate does not grow away from the grain boundary into the matrix, but grows as a network of large thin dendrites in between the grains. IN austenitic stainless steels the carbon in supersaturated solution precipitates when the steel is heated in the temperature range 450" to 1000°C. During such heat treatments the chromium-rich carbide occurs primarily at the grain boundaries and has adverse effects on the corrosion resistance and low-temperature ductility of the material. It has been shown that the morphology of the precipitated particles differs widely depending on the time and temperature of the heat treatment, the nature of the boundary, the misfit between the grains, and so forth.1"5 It was assumed by Mahla et al.,&apos; Streicher,&apos; and Mc Nutt&apos; that the carbide particles which nucleate in the grain boundary grow in various geometric or dendritic forms away from the boundary into the matrix. However, Kinzel,&apos; Hatwell et a, and Plateau et aL4 found that the particles nucleate in the grain boundary and grow as a network of thin dendrites in the grain boundary interface. We have made a comprehensive studyg of the precipitation occurring in a commercial 302 austenitic stainless steel heat treated for times ranging from 0.15 to 1500 hr at various temperatures from 480" to 1065"~. This study was made to elucidate the influence of heat treatments on both the mechanical and the corrosion properties of this steel. Part of this investigation which is pertinent to the morphology of the grain boundary carbides referred to above is separately reported here. We found that the particles which nucleated in the boundaries grew in the interface of these boundaries, thus supporting the viewpoints of Kinzel,&apos; Hatwell et al.,3 and Plateau et al.4 Furthermore, when carbide particles nucleated in the matrix very close to the boundaries, they possessed a morphology distinctively different from the particles growing in the grain boundaries. MATERIAL A study of metallographic samples and of fracture surfaces of a 302 stainless steel is reported in this paper. The composition and heat treatments are listed in Table I. Polished and etched samples were examined und813r the optical microscope, and carbon extraction replicas of etched micrographic samples and various fracture surfaces3&apos;8&apos;9 were examined under the electron microscope. RESULTS AND DISCUSSION A representative optical micrograph of the 302 steel, condition A, is shown in Fig. l(a). Particles can be seen on the grain boundaries but no traces can be found of particles which grow from the grain boundaries into the matrix. A carbon extraction replica of this sample shows numerous large thin dendrites, Fig. l(b). The lateral dimension of such carbide particles vary up to 100 p, and their thickness estimated from the amoun! of electron penetration i:; between 500 and 1000A. Such large dendrites are extracted from almost all grain boundaries and, if they had grown into the grains, they would definitely be revealed by etching traces in the matrix, Fig. l(a). The reason why these large dendrites on the extraction replica appear to be grown into the grain is due to the mechanism of the extraction replica process. Thus, these dendrites are supported by the carbon replica film only at the edges originally along the grain boundary trace A-A, Fig. l(b), in the polished metal section and have subsequently fallen over onto the carbon replica film during handling. Although such dendrites generally fall only to one particular side of the grain boundary trace, one finds occasionally that parts of a dendrite have fallen to both sides, as shown in Fig. l(b). Further evidence for the growth of carbide in the grain boundary can be obtained from the appearance of fracture surfaces. A small impact specimen of the 302 steel, condition A, was broken at liquid nitrogen temperature. The fracture path follows the

Jan 1, 1962

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria &apos;Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By R. C. Earlougher

Jan 1, 1970

By Thomas Leonard Watson

Jan 1, 1906

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"&apos; or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51&apos; 2" long, 17&apos; 4" wide, 31&apos; deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45&apos; 4" long, 11&apos; 16" wide, 31&apos; deep, divided into six parts by buttons 8" x 12", each division, 7&apos; x 11&apos; 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969