Search Documents

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Wilfred P. Sykes

AT intervals in the course of history an event occurs which, though scarcely heeded at the moment, marks in retrospect the beginning of a new era in some one field of human activity. Such a happening is perhaps more readily spotted in the field of technology than in other realms of human endeavor. Here the span of years is relatively short and the records have been kept with some degree of precision. In the current scene of our social and economic drama the art and science of metallurgy is playing a major role. Off stage will be found the metallurgist in one guise or another aiding, he trusts, in the development of processes and products which will contribute to the happiness of his fellow men. The results of his efforts appear in the form of metallic substances known as alloys built up from any two or more of the wide variety of metals which have been extracted from the mineral deposits in the earth's crust. An alloy by virtue of its inherent physical properties may seem ideally suited for human use in a special way but until this material can be produced economically it will fail to attain a place of prominence as an article of commerce. In fact many commercial alloys are being continually replaced by new or modified compositions better suited to meet the increasingly severe demands of industrial service.

Jan 1, 1939

[OFFICERS AND COMMITTEES J. W. Woomer, President A. B. Cummins, President-elect S. D. Michaelson, Past President C. E. Lawall, Eastern Regional Vice-President D. W. Scott, Central Regional Vice-President J. D. Forrester, Western Regional Vice-President R. B. Ladoo, Treasurer John Cameron-Fox, Secretary]

Jan 1, 1961

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By W. A. STERLING

IN the opencut iron mines of the Mesabi Range in Minnesota, the trend in mining is in the development of mining equipment and mining methods which will move surface overburden and ore-bearing materials with less labor and at a cheaper cost. This is a must for most of the independent operators. Their reserves of direct-shipping ore are extremely small and their operations are being conducted in small, or intermediate pits, with a high stripping ratio in the outer fringes, or shore lines of older pits. and in ore bodies passing from direct shipping to the washing and the intermediate, or retreat ore state. The trend is toward deeper stripping, longer and steeper hauls, and the necessity of moving a total of from three to five or six tons of overburden and ore material for each ton of shipping-grade ore produced. This naturally calls for greater production, with larger shovels, or draglines. cheaper drilling and blasting costs through the drilling of larger-diameter blastholes, and cheaper haulage through the use of trucks of larger capacity and more extensive use of belt-conveyor systems. This trend is notable both in stripping and mining.

Jan 1, 1948

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970

By Charles J. Moore

It seems a duty incumbent on the older members of the Institute to set forth in permanent form some of the results of their experience for the benefit of the younger members; this is the principal object of the present paper, which is the result of a recent examination requiring somewhat unusual geologic investigation. History. The London vein mas first discovered by float and occasional outcrops in the year 1873, four years before the great lead carbonate discoveries of Leadville, but the mine was not definitely located and opened until two years later, when the present locations, Mother, Paris, London, and Hard to Beat, were surveyed for patent. Since 1875 the London mine has been worked almost continuously until 1911, when the force was reduced to a few men only. In its early life the ore was assumed to be free-milling gold-quartz, although lead was a constituent of the vein throughout, and much useless expenditure was made in the erection and operation of a free-gold stamp-mill, with plates and tables for saving concentrates. The vein then opened was in the porphyry-limestone contact, a siliceous lead-ore, clearly most amenable to reduction by lead-smelter. The losses due to this process led in time to the close of the mill. For 20 years past, the mine has been worked under lease and the ore shipped to the lead-smelters in Denver or Salida. In January, 1912,I examined the mine to ascertain whether it was advisable to run a cross-cut tunnel some 4,200 ft. in length to intersect the main vein at a depth of 650 ft. below the present lowest workings. Finding a greatly-faulted zone, a close determination of the geological conditions became necessary to the solution of the problem.

Jan 1, 1914

By Frank F. Poland

TEE purpose of this paper-is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possible the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. PURPOSE OF DEVELOPMENT It was recognized early in the war effort that nickel would become a critical metal, therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elements (maximum), 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the con- version was successfully made.

Jan 1, 1946

By John Birkinbine

(Wilkes-Barre Meeting, June, 1911). MODERN advances in practically all lines of industrial development have occurred in such rapid succession, and have been accepted so readily as accomplished facts, that a retrospect surprises us, by showing how comparatively few of the acknowledged factors of improved conditions may be considered as old. While these advances have not been confined to any country, they have been more pronounced in some than in others, and nowhere more so than in the United States, the population of which, having multiplied nearly three-fold between 1870 and 1910, demanded a proportionately greater increase in materials, supplies, and manufactured products. It therefore appears desirable to discuss mainly conditions in the United States, as concrete evidence of industrial progress throughout the world. Looking backward for but three generations, we may trace the introduction and development of canal- and steamboat-navigation; railroad-transportation; artificial illumination beyond that furnished by candles and lard-oil; quick communication by mail, and subsequently by telegraph or telephone; the manufacture of iron, beyond forms of small dimensions; the production and utilization of steel in large quantities; the economic use of mineral fuel, oil and gas, etc. The practical coincidence of the fortieth anniversary and the 100th technical meeting of the American Institute of Mining Engineers, offers temptation to recall and compare the conditions of mining and metallurgy in or about the years 1871 and 1911. A complete resume would cover phenomenal changes in mining-methods and equipment by which the output of individual exploitation has grown from scores to hundreds and even thousands of units in equal time-intervals. Extension of operations in depth and area, demanding machinery of great power

Aug 1, 1911

Dr. James Douglas, who is memorialized on another page of this Bulletin, who held a place in the affections and regard of Institute members second to that of no other living roan, left in his will the sum of $100,000 for the maintenance of the Library of the American Institute of Mining Engineers. This is in addition to the $100,000 which Dr. Douglas gave during his lifetime. We believe that it is Dr. Douglas&apos; wish that the library, the great means by which the benefits of Institute membership may be extended to those distant from headquarters, should be maintained by the Institute at the highest possible level of efficiency and serviceability.

Jan 9, 1918

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout&apos; Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By Joseph Daniels

(San Francisco Meeting, October, 1911.) I. THE FRITZ ENGINEERING LABORATORY. TEE Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. . The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem, and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight, 84 ft. long and 9 ft. wide, in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section, containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Feb 1, 1912

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.&apos; It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.&apos; Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.&apos; It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.&apos; Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By Paul F. Kerr, Donald M. Hausen

Fine colloidal gold near Carlin, Nevada is disseminated in leached carbonate strata of the Roberts Mountains Formation in the Lynn "window" of the Roberts Mountains thrust fault. The ore body is generally stratiform and is more or less conformable to altered beds near the top of the formation, underlying Devonian limestones. Two sequences of mineralization are recognized: ( 1) an earlier base metal-barite assemblage related to early Cretaceous intrusives (121 ± 5 m.y.), and (2) a later low temperature Au-As-Hg-Sb assemblage of near surface emplacement. The earlier sequence consisting of sparse galena and sphalerite in barite with anomalous amounts of zinc, lead, nickel and copper, associated with dikes of dacitic composition, is of little economic importance. The later sequence of gold, realgar, cinnabar, and stibnite associated with extensive silicification and argillic alteration of limestone beds, has resulted in important deposits of gold. Argillic alteration of hydrothermally leached carbonate strata has provided the environment in which the most prominent gold deposition took place. Carbonate minerals in the limestone host rock have been replaced by microcrystalline quartz and chalcedony to form stratiform silica masses and recrystallized lenses of euhedral quartz. Zones of porous silicification are light gray to white, elliptical in shape, and more or less follow bedding. Silicification is bordered by argillic alteration and pyritization. Deposition of gold usually lies in a zonal pattern that encircles chimney areas of silicification.

Jan 1, 1968

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By Mark C. Malamphy

AT present the Federal Government represents the only organization applying geophysical methods of prospecting in Brazil. The geophysical work of the National Department of Mineral Production, which will be described in the following pages, must be considered as a program of experimental work designed to demonstrate the applicability of the more or less "standard" methods of geophysical prospecting to various problems of economic interest in Brazil by means of practical examples of results obtained in certain typical areas. Our work is somewhat similar to that of the Imperial Geophysical Experimental Survey of Australia, but our task has been greatly simplified by the ever increasing number of technical publications relative to the theory of instruments and methods.

Jan 1, 1936