Search Documents

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By David Cornell, D. L. Katz

Procedures for computing turbulent flow of gas in steady state near the well bore and a graphical method for predicting unsteady state laminar flow at distances from the well have been combined to compute pressure gradients in gas reservoirs. Methods are discussed for predicting single and multiple transients at constant flow rate in an infinite reservoir, predicting constant How rate. in a finite reservoir, reproducing and interpreting back pressure test data, and prediction of the behavior of a closed-in gas well. An example of the graphical method is given for a single transient and the results are compared to a published analytical solution. A typical calculation of the pressure gradient in a reservoir and the production of gas is made .starting with data from a hack pressure test. INTRODUCTION The calculation of pressure gradients throughouse a ga-reservoir at any point in its production history is a complex problem involving turbulent flow near the well bore and unsteady state flow of the gas from the reservoir. The problem is complicated further by the variety of boundary conditions that may be imposed upon the flow. Such boundary conditions include finite or infinite reservoirs. constant or variable rates of production, constant or varying bottom hole pressures, complex initial pressure distributions throughout the reservoir, and pressure maintenance through cycling. In addition to these problems there are the practical difficulties associated with natural gas reservoir analysis These might include: (1) variation. in the permeability and porosity throughout the formation. (2) variations in the thickness of the formation, (3) communication of the producing formation with other producing zones. (4) radial variations in permeability due to influx of drilling fluid. acidizing. or the buildup of liquid in the formation around the well, (5) partial penetration of the producing zone. (6) water flood, and many others. These problems will be considered eventually. In the mean- time, it is necessary to present methods of handling the case of radial flow through a homogeneous, regular, producing stratum to a single well uncomplicated by other factors. The idealized case of steady state, radial flow from a natural gas reservoir was studied by Elenbaas and Katz5 and by Mac-Koberts.' An analysis of the unsteady flow of gases through porous media has been made by Aronofsky and Jenkins' for the one dimensional laminar case with the boundary conditions of constant downstream pressure and uniform initial pressure. Solutions for the partial differential equation for unsteady state radial flow of liquids through porous media have been given by Van Everdingen and Hurst" for the constant bottom hole pressure and constant production rate cases for laminar flow in a reservoir initially at a constant pressure. The analogous heat transfer equation has been treated by Perry and Berggren9 for the case of quenching a cylindrical hole in an infinite medium to a constant temperature. The back pressure curve, which involves the variation of the bottom hole pressure as it is determined by the behavior of the reservoir as a whole. has been studied by Rawlins and Schellhardt,10 Binck-lev,' Baumel and Breitung,' and others. No complete. adequate treatment has been given for the unsteady state, radial flow of gases into a cylindrical hole from a porous medium with or without the presence of turbulent flow and for any set of boundary conditions. If one relies only on analytical solutions of the basic equations, a new solution must be obtained for each new boundary condition. Furthermore, the complexity of the mathematical expressions for boundary conditions other than the very simple cases limits the use of analytical solutions. Graphical methods exist, however. that are general in nature, accurate, and readily employed. The analysis of steady and unsteady, laminar and turbulent, radial flow for various boundary conditions with application to specific natural gas well problems by means of graphical procedures forms the content of this paper. STEADY STATE RADIAL FLOW EQUATION FOR LAMINAR AND TURBULENT FLOW A steady state radial flow equation for laminar and turbulent flow through unconsolidated sands has been given by Muskat as discussion of the work by Elenbaas and Katz.5 This equation is based on the properties of unconsolidated

Jan 1, 1953

By A. C. D. Chaklader, Ashok K. Kakar

The basic density equation originally dericed ' to predict the increase in density of a compact of spherical particles with the progressive deformation at the points of contact has been further modified to include the yield strength of the material. This has been done by assuming that the contact areas grow to stable sizes under a fixed stress which is equal to three times the yield strength. The final equation has the form: where Do and D me the initial and final bulk densities of the compact, u is the applied pressure, and Y is the yield strength of the material. This equation was tested with the data obtained on spheres of lead, K-Monel, and sapphire. The calculated yield strength t~alues for lead and sapphire are within the range of values reported in the literature. A few of the earliest hot pressing models proposed to explain the mechanism by Murray, Livey, and williams2 and then by McClelland3 are based on a plastic flow mechanism. However, more recent investigations suggest that the overall densification process is a combination of several mechanisms, such as particle rearrangement, fragmentation, plastic flow, and stress-enhanced diffusional creep. While fragmentation and particle rearrangement are considered to be responsible for the densification in the early stages,"475 it has been concluded that the final stages of hot pressing are controlled by stress-enhanced diffusional creep.516 The manner in which the densification takes place, i.e., by fragmentation, particle rearrangement, plastic flow, or stress-enhanced diffusional creep, would depend upon the type of material, the temperature, and the stress level used during the hot-pressing experiments. Metal compacts can be expected to have a much greater contribution from plastic flow than ceramic oxides. Also, plastic flow would be a significant contributing factor to densification at high temperatures and high stresses. Most of these works, directed towards elucidation of densification mechanism, have dealt with kinetics of the process. The results of most of the authors vary from one another and they have proposed either new empirical or semiempirical equations to fit their data. The densification rate was found to vary with the type of the powder, shape and size of the powder, initial packing density of the compact, and a few other factors such as rate of heating, pressure, and so forth. Beyond the initial stages, the densification process has been considered to be as time-dependent flow, controlled by a diffusional process, e.g., Nabarro-Herring creep. Palm our, Bradley, and johnson' have attempted to use modified creep rate equations to interpret the data of densification under hot-pressing conditions. Beyond the initial stages, however, the densification would be controlled by a process depending upon the temperature, pressure, and size of the powders. It is the authors' belief that such densification cannot be exclusively controlled by a single process and so attempts should be made to study some observable phenomenon like microstructure, yield strength, and so forth. The emphasis of this work has been toward studying the densification problem from a more fundamental point of view. Some of the principal variables, like initial packing density, mode of packing, and size of the powders, have been controlled to a great extent. The total strain produced on pressure application (instantaneous) in such a case can be considered to be due to plastic and elastic deformation. The elastic component of the strain can be determined by decreasing the load to the initial value. The strain remaining then can be correlated with the contact areas produced by deformation and the corresponding applied load. In a previous paper,' the possible deformation behavior of spheres in a compact has been theoretically analyzed and experimentally tested. The change in contact area radius a relative to the particle radius R was related to the bulk density and the bulk strain for simple and systematic modes of packing. Tt was found that a density equation relating the above parameters can be represented by: where D and Do are the bulk densities of the compact at any value of a/R and a/R = 0, respectively. This basic equation should hold for any material as it was derived from geometrical considerations alone. An attempt has been made in this work to include the yield strength in the above density equation, so that a knowledge of the properties of any material can be used in predicting the densification behavior during the hot-pressing process. THEORETICAL CONSIDERATTONS The deformation of two spheres in contact under a static load can be compared to the deformation occurring between a hard spherical indentor and the flat face of a softer metal. Tt has been shown theoretically by both ~encky~ and lshlinskyg and experimentally by ~abor" that, for a material incapable of appreciable work hardening, the mean pressure required to produce plastic yielding (for deformation occurring between flat face and a hemispherical indentor) is approximately equal to three times the elastic limit, Y, of the material (in tension or compression experiments). Tabor has further observed that the same relationship is valid in the case of work-hardening materials, if the elastic limit at the edge of the indenta-

Jan 1, 1969

By P. Chiotti, E. R. Stevens

The electromotive force between pure magnesium and Mg-Zn alloys in a fused KC1-LiCl-MgC12 cell was measured over the temperature range 360° to 730°C and for alloy compositions of 0.052 to 0.635 atom fraction magnesium. The calculated activity coefficients of magnesium in the liquid alloys may he represented by the relation These data and the phase diagram were employed in calculating the standard free energy of formation for the compounds MgZn, MgZn2, and MgZn2, In the temperature range from 25° to 590°C the relation ZINC-rich magnesium alloys have been shown to be very effective in reducing various solute chlorides or oxides from fused salts such as KC1-LiC1 eutectic. Such reactions are of interest in the developinent of pyrometallurgical methods for reprocessing nuclear reactor fuels.' As the conceniration of the magnesium is increased beyond 5 to 10 wt pct the extent to which solutes, such as yttrium, lanthanum, cerium, and other rare earths, can be reduced or removed from the salt decreases. This effect is due to the resulting change in the activity of the solutes in the Zn-Mg alloy as well as the change in the activity of both the zinc and mag- nesium. The purpose of the present investigation was to determine the thermodynamic properties of the Zn-Mg system which, in addition to yielding information on the alloying behavior of these two elements, would permit a more quantitative understanding of the above reactions. Since this investigation was initiated several publications have appeared in the literature giving results on the thermodynamic properties for the liquid alloys of this system. 2-4 Kozuka, Moriyama, and Kushima3 measured the vapor pressure of zinc over four different alloy compositions by a carrier-gas technique. Eremenko and Tukashenko2 and Terpilowski4 measured the electromotive force between pure magnesium and various alloys in a fused salt cell. Earlier work has been summarized by Hultgren, Orr, Anderson, and Kelley.5 In the present investigation electromotive-force measurements were made on a cell of the type The temperature range covered for the lower-melting alloys was roughly 375° to 730°C. These data were employed in calculating the thermodynamic properties for the liquid alloys and in conjunction with the phase diagram,' reproduced in Fig. 1, were used in calculating the standard free energy of formation of the compounds MgZn, MgZn2, and Mg2 Zn11. The results obtained are compared with available data from the literature. MATERIALS AND EXPERIMENTAL PROCEDURES Materials employed were: Bunker Hill slab zinc, 99.99 pct pure; Ames Laboratory magnesium containing 13 ppm N, 195 ppm C, and trace amounts of calcium, copper, nickel, and silicon; reagent grade KC1, LiC1; and high-purity MgC12 obtained from Dow Chemical Co. The electrolyte consisting of KC1-LiCl eutectic (44.4 wt pct LiC1) to which was added 15 wt pct MgCl2, was dried in a quartz tube by heating to 340° C under vacuum for a period of 4 to 5 hr, and then passing HC1 through the salt as the temperature was slowly raised to above the melting point of the salt. After about 3 hr the HC1 was shut off and the system flushed with argon and then vacuum applied for 1 hr. The salt was finally siphoned through a sintered glass filter and cast into a Pyrex container which was sealed and

Jan 1, 1965

By P. Beardmore, B. W. Howlett, B. D. Lichter, M. B. Bever

The heats of formation at 273°K of the compounds Mg2Ge, Mg2sn, and Mg2b, the heats of fusion and melting points of Mg2Sn and Mg2Pb, and the heats of solution of magnesium, germanium, and lead in liquid tin have been measured. The excess free energies of the liquid alloys and the free energies of formation of magnesium-Group IVB compounds at their melting points and their standard free energies of formation at 298°K have been calculated. The stability and bonding of the compounds are discussed with reference to these properties. Some thermodynatnic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. THE compounds of magnesium with the Group TVB elements, silicon, germanium, tin, and lead, have often been considered to constitute a nearly ideal homologous series. In particular, their thermodynamic stability has been assumed to decrease with increasing atomic number of the Group IVB element.' The binary-phase diagrams of the magnesium-Group IVB elements given by Hansen and Anderko2 have the same form. Each system has a single con-gruently melting compound of limited homogeneity range. The structures of these compounds, which have the formula Mg2X, are anti-isomorphous with the calcium fluoride structure. A recent investigation has found evidence of a second compound in the system Mg-Pb.3 The solid compounds Mg2Si, Mg2Ge, and Mg,Sn are semiconductors, while the conductivity of Mg2Pb approaches that of a metallic conductor. This difference suggests that other properties may also show a discontinuity. The investigation reported here is concerned with the thermodynamic properties of magnesium-IVB compounds and particularly their variations with the period of the Group IVB element. The heats of formation at 273°K of the compounds MgzGe, Mg2Sn, and Mg2Pb and the heats of fusion and melting points of Mg2Sn and Mg2Pb have been measured. The results, combined with published data, are interpreted in relation to the stability and the bonding characteristics of the compounds. Some thermodynamic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. In the course of the investigation the heats of solution of magnesium, germanium, and lead in liquid tin have been determined. 1) EXPERIMENTAL PROCEDURES 1.1) Samples. Samples of the compounds Mg2Ge, Mg2Sn, and Mg2Pb, supplied by Professor P. Aigrain, Compagnie Générale de Télégraphie Sans Fils, were used in measuring heats of formation, heats of fusion, and melting points. Samples of Mg2Sn and Mg2Pb, supplied by Dr. V. B. Kurfman, Dow Metal Products Co., samples of Mg2Sn, prepared at the Air Force Cambridge Research Laboratories, and samples of MgzPb, prepared in this laboratory, were used for additional measurements of the heats of fusion and the melting points. The samples were stored in evacuated Pyrex capsules or under nonreacting liquids. 1.2) Heats of Formation. The heats of formation at 273°Kof the compounds Mg2Ge, Mg2Sn, and Mg,Pb were measured by tin-solution calorimetry. In this method, samples of the compound and of a mixture of the constituent elements are added alternately from 0°C to a tin-rich bath. The difference between the heat effects, corrected for the change in composition of the bath, is the heat of formation of the compound. Details of the method have been given elsewhere. 4 The bath was maintained at 350°C for the dissolution of the compounds MgzSn and Mg2Pb. Since at this temperature the dissolution of Mg2Ge was too slow, a bath temperature of 400" or 450°C was used with this compound. At least three calorimetric runs, each of approximately six additions, were made with each compound. 1.3) Heats of Solution. The determination of the heats of solution of magnesium, germanium, and lead in tin was included in this investigation because they were not well-established at the time this work was started. To obtain the heat of solution, the difference

Jan 1, 1967

By H. R. Drullard

TO obtain the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid grease should be used. The lubricators should be filled once for every 12 or 14 ft. (3.5 to 4 m.) of hole drilled. Grease guns should be used to fill the port in the chuck end once a shift; a medium (No. 3) grease is well adapted to this purpose. Hard grease must not be put into the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of hole drilled. The rotating handle of a stoping drill is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wick-ing, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at least twice a shift; lighter oils than castor, such as Arctic Ammonia, may be used. Drills used in shaft sinking can be oiled satisfactorily by placing a good-sized, drop, sight lubricator on the station above the sinking operations and connecting it with the air-line supplying the sinking drills. If this lubricator is properly filled and adjusted, a uniform oiling of the sinking machines will be effected without the necessity of oiling the drills individually. The grease end should be filled at the station or surface before each drilling period. The shift boss should see that the machines are greased and also that the lubricators at the station function properly. The life of the air-drill hose is somewhat shortened by this method, as oil attacks the inner tube; but as some oil is always present in the compressed air, this is not a serious objection to the method.

Jan 1, 1922

By R. E. Reed-Hill, W. H. Hartt

High-purity magnesium single crystals, oriented with basal plane parallel to stress axis, were deformed in tension at room temperature so as to form second-order (1011)- (1012) twins. Investigation by optical and replica electron microscopy revealed that these twins can support very large internal strains approaching 1000 pct and that fracture follows as a direct consequence of these strains. At low strains the basal plane within (10i1)- (10i2) twins rotates with increasing deformation until it becomes approximately parallel to the twin boundaries. This rotation is not consistent with deformation by basal slip in the double twin, but may be rationalized in terms of nonbasal slip. Observations also indicate that basal slip in the primary (1011) twin, prior to second-order twinning, may contribute to this rotation. Deformation markings that are difficult to interpret in terms of slip on previously observed systems were noted in the twin bands. A possible means of rationalizing these markings is to relate them to grain boundary shear. The fracture associated with these twins is thought to initiate by formation of voids at the twin boundaries. These grow into microcracks, with ultimate fracture occurring by tearing of the interconnecting regions. THE significance of deformation and fracture along second-order (10i1)-(10i2) twins in polycrystalline magnesium1-' and many magnesium alloys4 was discussed in a previous paper.5 It was noted that this double twinning mode effectively controls the room-temperature deformation and fracture of magnesium single crystals, oriented with the basal plane parallel to the tensile axis. Reed-Hill and Robertson6 observed that, although these crystals may fracture at a macroscopic strain of less than 1 pct, shear strains up to 1000 pct could occur within (1011)- (10i2) twin bands. They concluded that the fracture was "ductile" and resulted from concentrating the deformation into a very small volume. The present research was undertaken to obtain a better understanding of the deformation and fracture associated with these twins. EXPERIMENTAL TECHNIQUES The experimental procedure involved straining high-purity magnesium single crystals in tension at room temperature. Specimens were oriented so that the applied stress direction was within 2 deg of the [1010] crystal axis. The specimen cross section was rectangular with faces closely parallel to (1210) and (0002). The specimen preparation and testing procedures have been described in detail elsewhere.5 Second-order (1011)- (1072) twins nucleated during straining were studied using optical and replica electron microscopy techniques. For the latter, cellulose acetate-carbon double replicas were employed. Observations were made on the (1210) crystal surface, which is the plane of shear for twins of this type. In addition to the single crystals, some investigations were carried out on longitudinal polycrystalline specimens. These were obtained from high-purity magnesium plate with a texture in which the basal planes of the grains tended to be nearly parallel to the specimen axis. All. polycrystalline specimens were annealed prior to testing in order to produce a coarse grain structure, permitting Laue back-reflection X-ray photographs to be obtained from grains of interest. EXPERIMENTAL RESULTS a) Deformation Within ( 101 l )-( 1072) Twins. Fig. 1 is an optical micrograph demonstrating the extent of the plastic deformation that can occur in (1011)-(10i2) twin bands. Notice at the lower left corner of the photograph the large displacement of the dark band (a polishing step) where it crosses the twins. The shear strain in the twin band at this position was computed to be 700 pct, using the ratio of step width to twin thickness. It was previously shown5 that (1011)- (1012) twin bands are often composed of small, separate twins aligned close to the macroscopic habit plane. Fig. 2 is an electron micrograph from near the upper end of the twin band in Fig. 1. This illustrates that the twin habit often does not coincide exactly with the macroscopic band habit, but may be inclined at a slightly smaller angle to the matrix basal plane. Figs. 3 through 6 are electron micrographs of the twin band in Fig. 2 illustrating successive steps in the development of deformation inside the band. A twin band such

Jan 1, 1969

By Robert H. Richards

Tuns truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo in May, 1896. The first table sold for installation was placed' in the Puzzle mill, Breckinridge county, in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to pre¬sent them so clearly that their bearing can be seen by all. To this end two complete series-'of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jul 1, 1907

By Gilbert P. Moore

Bolivia does not yet have any production which is being marketed. It does have a potential production, however, from wells which have been completed by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey. No other company is active in drilling and development work to date. The total potential production from wells now completed is about 6000 bbl, daily. Wells Completed Completions during 1928 and their initial daily productions. if any, were as follows: Camatindi No. 1, 350 to 1000 bbl.: Camiri No. 1, 500 bbl.; Sanandita No. 3, 100 bbl.; Tatarenda No. 1, dry hole, and Bermejo No. 2, deepened 50 ft. made 1000 barrels. The most striking development of the year was the Camiri No. 1 well which, after just entering the sand, made 500 bbl. per day of 52" B. oil. This well is the northernmost good producer which the Standard has brought in to date. Oil from this well is used without refining in the tractors and trucks of the company. A small topping plant has been installed from which high-grade gasoline is obtained for use in motor cars and some is being produced for the use of air plants stationed at Villa Montes. The results for Sanandita No. 13 were somewhat disappointing since Sanandita No. 2 was rated at about 3000 bbl. Tatarenda NO. 1, located on a large unbroken structure, was drilled to 4000 ft. and abandoned as a dry hole. Bermejo No. 2 was deepened 50 ft. to 2085 ft.. and on a 10-day test averaged 1000 bbl. per day. This well is on the border between Bolivia and the Argentine. Wells Drilling The wells drilling are Camiri No. 2, Sanandita No. 5, Machareti No. I and Bermejo No. 5. This is the smallest number of drilling wells which the Standard has had for several years but is principally due to

Jan 1, 1929

By H. J. Wasson

At the close of 1927 Venezuela was producing at the rate of 205,000 bbl, per day, making it the third country in the world in point of present daily production. For the year, the total was close to 64,000,000 bbl., representing an increase of about 70 per cent. over the 37,000,000 bbl. in round numbers produced in 1926. All of the 1927 production canie from fields opened up before the beginning of the year. While no new fields were added to the list of shippers, the past 12 months' wildcatting yielded a fair quota of new discoveries which, in the light of prcsent results, may be considered likely sources of production in due time. Altogether three such promising finds were made Of first importance, at least for the immediate future, is the completion by the Lago Petroleum Corpn. of the San Matins well, 4 miles north of the present edge of the Lagunillas field. Although rated as only a 125. bbl. well, at 3217 ft., it indicates a probable extension of the field over the intervening 4 miles between the two. The two other wildcat discoveries of importance were the Los Manueles well in the District of Colon, which has in all probability opened up a new field about 7 miles north of the present Tarra oprations; and the Honibre Pintado well of the Standard Oil Co. of Venezuela,. in the State of Falcon, which is considered to be a promising clc~vc~lop~ncnt. Neither of these last mentioned two discoveries will apprcciably affect production during 1928, as the Manueles area must await the carrying out of a general plan for the exploitation of the District of Colon, a problem requiring time. The Hombre Pintado area is being tested further, but doubtless several wells will be put down before. anything definite will be done towards making the pipe line. arrangements that rnust necessarily precede the commercial exploitation of the field. The San Matias Well The San Matias well is a highly significant dcvelopment,. It is located along the trend of the La Rosa-Ilagunillas producing formations, and when drilling started, production in the Lagunillas field was 4 miles

Jan 1, 1928

By J. Szekely, Robert G. Lee

Calculations are presented for the prediction of the combined radiative-convective heat loss from molten steel held in a ladle, covered by initially molten slag. A mathematical formulation is given and numerical solutions are presented of the resultant partial differential equation. It is shown that a slag layer of about 2 to 3 in. thick would prevent any significant heat loss from the top metal surface for Periods of up to 1 hr. For thinner slag layers (or in the absence of the protective slag) appreciable heat losses would occur; plots given in the paper allow the quantitative evaluation of the fall in the metal temperature due to this heat loss. The ironmaking-steel processing operation involves several intermediate steps where the molten metal is held or transfered in ladles. The quantitative assessment of the heat losses occurring under these conditions is of considerable importance in process design considerations since the temperature of the metal may have to meet rigid specifications in any given part of the processing sequence. While the metal is held in a ladle, heat is lost by two mechanisms: i) by conduction into the ladle walls; ii) by radiation and convection from the top surface. Calculations relating to the conductive heat loss, are readily made and information may be found in the literature both on data pertaining to metallurgical situations and on the techniques that are available for performing additional computations.'-3 The evaluation of the combined convective-radiative heat loss is less straightforward, especially when there exists a protective slag layer covering the metal. In this latter case, as the top slag surface loses heat partial solidification may occur and the latent heat thus given up by the slag may represent an effective barrier to the heat loss from the metal. A semiquantitative assessment of the role played by the slag in preventing heat loss from the metal has been made in a previous paper,4 where it was shown that a slag layer 6 in. thick would act as a near-perfect insulator for periods of up to 2 hr. However, this first paper reported on an essentially preliminary investigation that considered only one slag layer thickness; furthermore, the boundary conditions used for the calculations were somewhat restrictive since no allowance was made for changes in the metal temperature. The purpose of this second paper is to extend the scope of the preliminary investigation previously reported by: i) considering several slag layer thicknesses; ii) allowing for variations in the metal temperature; and finally iii) by performing calculations on the net loss from the metal rather than from the slag surface. FORMULATION Consider a slag phase extending from y = 0 to y = L1, covering a metal phase that occupies the region extending from y = Ll to y = L, as illustrated in Fig. 1. Denote the slag and metal temperatures by TS and Tm and assume that initially both slag and metal are molten, having a uniform temperature Ti. At time = zero the surface represented by the y = 0 plane (top slag surface) is brought into contact with cold air, the temperature of which is given as T Thus for time > zero, heat will be transfered from the slag to the air by natural convection and thermal radiation; as a result of this heat loss the slag temperature will fall and after some time a solid phase is formed and a solidification boundary (more realistically described as a zone) will move progressively from y = 0 toward y = L1. Once the region of temperature gradients, moving ahead of the solidification zone, reach the slag-metal interface (y = L1) there will be a net transfer of heat from the metal through the slag to the cold air, across the y = 0 plane. In the formulation of moving boundary problems, involving phase changes that require computer solution, it is convenient to represent both phases by a single equation, making allowance for the latent heat of solidification by assigning an appropriate temperature dependence to the specific heat content. Thus the energy equation for the whole of the slag may be written as follows:

Jan 1, 1969

By H. C. van Elst

Ultrahigh-speedphotographic and electronic meth-ods were applied to an investigation of details of brittle-fracture propagation in steel. The brittle fractures studied were obtained in steel plate with the aid of a Robertson apparatus. It was found that a brittle fracture proceeds by discrete steps ranging from 30 mm near the stop temperature to less than 2 mm at lower temperatures. The halting FROM prior metallographic observations of brittle fracture in steel' it could be concluded that the distribution of mechanical twins along a brittle fracture was similar to the distribution of mechanical twins induced by explosive deformation. It was therefore assumed that a running brittle fracture created stress waves, cf. Refs. 2-7. An emission of stress waves by a brittle fracture, however, seems only conceivable if the fracture propagates by discrete steps. For this reason a study of the details of times between successive steps drop in this tem-perature region from 20 usec to about 1 psec. The stepwise propagation mechanism is accompanied by an intermittent emission of stress waves of the order of 100 to 200 kg per sq mm. These stress waves seen1 to play an important role in the mechanism of brittle fracture as will be discussed. brittle-fracture propagation was undertaken to investigate the possible determination of the fracture steps and the emitted stress waves associated with the assumed mechanism. The more practical object of this work is the development of a test method for the determination of the ductile-brittle transition in small specimens. This has special advantages for the study of irradiation damage in steel. In this test method, which will be published in a following paper, the stress waves emitted by an actual brittle fracture are reproduced with explosive or electrical means and are then transmitted through small specimens at various temperatures. In the present paper only the results of the brittle-fracture study will be reported.

Jan 1, 1964

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10' greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.' In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist's work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931

By Frank R. Milliken

Before the rather sudden economic downturn in recent months, shortages of materials were painfully felt throughout the US. The current recession has provided a temporary relief here and there-but energy fuels and a number of staples such as sugar are still in short supply. This is an unsolved and fundamental problem that will haunt us again as the economy turns up. There is an awareness that the nation faces a widening supply gap in many of its most basic materials-from asbestos to tungsten-as evidenced by recent studies and government reports, and by the Secretary of the Interior's annual warnings about the mounting seriousness of the problem.

Jan 3, 1975

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows The Robert W. Hunt Medal and Prize, The J. E. Johnson, Jr , Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules¬ 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize. The money prize shall not be awarded to -a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side m recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval.. , 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5 The recipient of the award shall be designated "The Hunt Medallist " This prize is administered by the Iron and Steel Committee.

Jan 1, 1923