Search Documents

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry&apos;s law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry&apos;s law is obeyed, one canthen use the Van&apos;t Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors&apos; Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott&apos;s results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

By John Gillie

PRioR to the year 1902 electricity was used in the Butte district only for lighting, for the tramming of ores on the surface, and for the electrolytic refining of copper. In that year the Canyon Ferry hydro-electric plant on the Missouri river, with a transmission line to Butte and Anaconda, was completed, and enabled the mining operators to purchase electric current in large quantities at reasonable rates, and its application and use in the various mining operations and reduction works proceeded rapidly. The principal applications of electric current in metal mining may be listed as follows: Compressing air for hoisting. Compreeaing air for rock drills and pneumatic tools. Pumping. Ventilating. Lighting. Tramming. Compressing air for blast furnaces and converters Running shop and miscellaneous motors. Compressed Air for Hoisting. The Anaconda Copper Mining Co. operates 22 mine shafts and plants at Butte. Of these, 15 are large plants and hoists, through which most of its ores are hoisted. In 1912 this company commenced using compressed air in place of steam, in operating a number of its large hoists, and at this date has 10 main hoisting engines and 10 auxiliary hoists driven by compressed air. The compressed air is furnished from a central plant containing six compressors, each having a capacity of 7,500 cu. ft. of free air per minute compressed to 90 lb. pressure in large receivers, and conducted by suitable pipe lines to the various hoists, the air being reheated before passing to the engines. Each of these compressors is driven by a 1,200-h.p. synchronous motor, directly attached to the drive shaft, and takes electric current at 2,200 volts. Two additional compressors are being installed,

Jan 1, 1914

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By H. K. Work, H. T. Clark

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By J. J. Gilman

WHEN a zinc crystal is immersed in liquid N, and then plastically bent, it is observed that it bends a certain amount and then fractures. This fracture occurs at a fairly reproducible radius of curvature, and the radius varies systematically with the crystal orientation. Because this phenomenon provides an unusually well-defined set of fracture conditions, it is possible to examine various possible fracture criteria and select the best one. Zinc crystals of various orientations were bent about axes lying in their glide planes (0001) and perpendicular to their glide directions [1210]. The crystals were 0.150 in. diam and had chemically polished surfaces. They were immersed in liquid N, while they were being loaded on an Instron testing machine. A three-point bending jig was used to load them. Table I lists the beam radius at which fracture occurred for each orientation. Each value is the average of at least six measurements. The normal stresses on the cleavage planes, at the time of fracture, were calculated as follows: First, from the fracture radius, R,, the orientation angle, x,, of the (0001) plane at the outer fiber was calculated. If x, = angle between the (0001) and the rod axis prior to bending, d = rod diameter, and X, = angle between the (0001) plane and a tangent to the bent crystal, then1 sinX, _ 2R, sin xn 2R, + d Since the glide shear strain is given by&apos; y &apos; cot X, — Xo the glide strain at fracture, x,, can be calculated. Next, it is necessary to know the tangential stress in the outer fiber at fracture. This depends on the plastic flow curve, so a series of tensile tests were performed at —196°C on another set of zinc crystals. A curve of the average resolved shear stress versus glide strain was prepared. From this curve, shear stresses, r,, corresponding to the glide strains in the bend tests were taken. These values are listed in Table I. Then the normal stresses in the outer fibres, u,, were calculated from the relation U, = r, tan X, This analysis assumes that the fiber stresses in a bent beam are the same as the stresses in simple

Jan 1, 1959

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45&apos; to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input—heat enerb output) used in creating new surface, gliding or slip on atomic planes, twinning, and possibly other lattice rearrangements within the mineral. If it be postulated further that with a hard, brittle crystalline material, such as quartz, the energy used to produce gliding, twinning, and other permanent lattice movements is a very small fraction of the total net energy absorbed, then this energy absorption within the grinding calorimeter can be ascribed to the creation of new surface energy alone. Such energy is, from the thermody-namic standpoint, the true effective work of the grinding device, in this case a tumbling-medium mill. The ratio of this effective work (in calories) to the total energy input (in calories) should express the thermodynamic efficiency of the comminution taking place under the conditions used in the grinding calorimeter. This approach to the measurement of the energetics of tumbling-mill grinding was suggested by some previous work by Fahrenwald and coworkers&apos; with a laboratory ball mill and a thermometer. They measured the efficiency of grinding based on the formula: Pct Grinding Efficiency = Energy (calories) — Thermal Energy x 100 1npZ Output (calories) Energy input (calories) Efficiencies thus measured, while grinding quartz sand, ranged from 19.7 pct to 7.4 pct. Cook in 1915,&apos; used this approach to the problem of grinding efficiencies in stamp batteries and obtained the energy input by stamp weights times drop distances and the energy output by means of thermometers and pulp flow rates. He calculated that 80 pct of the input energy to the stamp shoes was wasted as sensible heat in the ore pulp. No other studies of comminution by this method of energy differences came to the author&apos;s attention. Reasonable agreement as to the order-of-mag-nitude of comminution efficiencies in tumbling-media mills is lacking in the literature. There is a widespread impression among technical workers that the grinding efficiency of the industrial ball mill may be on the order of 1 pct, or even a fraction

Jan 1, 1952

By S. C. Schaeker, A. W. Schlechten, A. H. Larson

PARRAVANO and Malquori&apos; studied the equilibrium of H2S-Hz with molybdenum and its lowest sulfide which they believed to be MoS2. Mc Cabe&apos; has shown that its composition is actually Mo2S3 and determined its dissociation pressure by means of Knud-sen effusion measurements. Stubbles and Richard- son3 have recently studied the equilibrium of gas mixtures of H2S-HZ with the two-phase solid mixtures of Mo-MozS3 and Mo2S3-MoS2. The latter investigators found that M02s3 deviated slightly from the stoichiometric composition, but they did not determine the homogeneous region of the disulfide phase. Morimoto and Kullerud, studied the Mo-S system by quenching, microscope, and X-ray methods and concluded that the disulfide is stoichiometric. The present investigation was concerned with the measurement of the sulfur vapor pressure variation with composition at 1100°C in the homogeneous region of "MoS2". These measurements were made by reacting: 1) molybdenum powder (99.97 pct Moj with sulfur vapor, and 2) MoS1.g9 (formed by reaction of Mo + H2S) with sulfur vapor in a quartz capsule. Conditions were controlled to form an equilibrated phase within the homogeneous region of the disulfide. The quartz capsule was sealed off initially under a vacuum and the residual gases were gettered by titanium powder contained in one end of the capsule. A mixture of Mo + S or MOS,., + S was in the other end. The section containing the titanium powder was heated for 24 hr at 700°C and then removed by flame sealing. The end of the capsule containing the charge was then heated to 1100°C. The other end of the capsule was maintained at a temperature which would produce the desired sulfur pressure in the capsule (liquid sulfur distilled from the charge mixture was retained in this end). After equilibration, the capsule was removed from the heating assembly and rapidly air-cooled. It is assumed that equality existed between the total sulfur pressures (PT) in the two ends of the capsule and not between the partial pressures of the different molecular species (S, SZ, Three separately controlled heating elements were used to maintain the proper temperature gradient over the length (approximately 12 in.) of the capsule. A thermocouple-Wheelco "Capacitrol" system was used for temperature control of the two end heating elements within 2"C. The center heating element was controlled directly by a " Power -stat". Separate controlling and measuring thermocouples were used for both end heating elements. Pt-Pt(l0 pct Rh) thermocouples were used for 1100°C and Chromel-Alumel thermocouples were used for lower-temperature control and measurement of the assembly. Silver foil was wrapped around the end of the capsule containing the liquid sulfur to insure a constant temperature zone. The thermal gradient over the entire length of the capsule was measured to: 1) ascertain that the length of the constant temperature zone of the liquid-sulfur end and the sulfide end was sufficient, and 2) ascertain that the liquid-sulfur zone was the zone of lowest temperature. The data obtained in this investigation are shown in Fig. 1 and Table I. The total sulfur pressure (PT) and p(S2) were calculated from the data of Braune et UZ.~ The compositions of the equilibrated disul-

Jan 1, 1964

By M. R. Geer Olds, H. F. Yancey

.I. S. Huckaba (Western Machinery Co., Spokane, Wash.)—It has been my pleasure and privilege to be able to follow this work with the H.M.S. pilot plant very closely. This has been a very thorough and painstaking piece of work and will be of great value to the dense-media operators and manufacturers. Unfortunately time was not available to make an accurate comparison between this pilot plant and the commercial plant at Bellingham Coal Mines, both plants having Wemco drum separators. Briefly I would like to point out what I consider the most interesting finding of this work. Capacity: Very good results were obtained at a feed mte of 5.2 tons per hr in a 30-in diam by 24-in. long drum separator. The maximum capacity of this drum is not known but it is something over 5.2 tons per hr for the available area of 2.08 sq ft. Medium Preparation: The importance of proper medium preparation is well demonstrated. A "tailored" or

Jan 1, 1954

By John W. Bell

The aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger&apos;s method; (b) by Stadler&apos;s method, based on Kick&apos;s law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½-ft. Huntington mill was used.

Jan 1, 1918

By Ian MacGregor

As I drove in from the airport on Sunday somebody said &apos;On the right you will see Duntroon, which is the military training school of Australia.&apos; So I asked the driver, where did they get that name? &apos;Oh,&apos; he said, &apos;from some people who built a house there. That was it&apos;s name- Duntroon.&apos; It strikes a note with me because, that&apos;s the name of a 12th century castle on the west coast of Scotland where I spend what leisure hours I have and, therefore, it establishes the long connection between Australia and my native land. There is also a story I should tell you about the oil industry and its upsurge in Scotland recently which has resulted in great prosperity. And in Edinburgh, the walls of the banks are bulging-because of the incursion of foreign exchange and other resources. Charlotte Square, as some of you know, is the centre of the Scottish financial world and at one of the corners of Charlotte Square, where ho streets intersect, there are three stores-three emporia on the ground floor. Two of them at opposite corners are banks: The Royal Bank of Scotland, and not to be beaten by that, The Bank of Scotland. But the third building is occupied, or was occupied, by a furniture store over many years-very high-grade, high quality furniture that the elite of the Edinburgh society always supported. And suddenly, the store was cleared out and in came a bunch of carpenters and other people busily engaged in rebuilding the store, and finally the new tenants arrived on the scene.

Jan 1, 1978

By Louis A. Mattson, Winthrop A. Rowe, John T. Cumberlidge, Victor M. Mejia

The parent ultramafic of Nickel Mountain is an alpine-peri-dotite. Compositional layering and late stage dunites suggest the intrusive crystallized in the upper mantle or lower crust. The ultramafic mass was fault emplaced in the upper crust, probably during upper Jurassic time. Soil, saprolite and silica boxwork nickeliferous ores were formed over the Nickel Mountain peridotite during the development and later destruction of the Klamath peneplane. A complex fault pattern was produced by irregular gravity displacements along fault surfaces during the relative uplift of Nickel Mountain. The majority of the ores occur in the fractured hanging wall of these gravity faults. Consequently, structure mapping is important for mining purposes. Ore types at Riddle are classified on the basis of MgO, Fe, and Si02 contents as well as textures. The chemical, mineralogical and textural differences of the various ore types reflect differences in weathering histories. Satellitic ore bodies occur peripherally to Nickel Mountain. These are erosional remnants of landslides and large gravity fault blocks from Nickel Mountain.

Jan 1, 1976

By T. K. Perkins, O. C. Johnston

Because of the influence of dispersion on miscible-displacement processes, diffusion and dispersion phenomena in parous rocks are of current interest in the oil industry. This paper reviews and summarizes a great deal of pertinent information from the literature. Porous media (both unconsolidated packs and consolidated rocks) can be visualized as a network of flow chambers, having random size and flow conductivity, connected together by openings of smaller size. In such a porous medium, the apparent diffusion coefficient D is less than the molecular diffusion coefficient Do, as measured in the absence of a porous medium. For packs of unconsolidated granular material the ratio D/D, is about 0.6 to 0.7. For all porous rocks, both cemented and unconsolidated, the ratio of diffusion coefficients can also be represented as D/Do = 1/FF where F is the for- mation electrical resistivity&apos; factor and 4 is the porosity. If fluids are flowing through the porous medium, dispersion may be greater than that due to diffusion alone. At moderate flow rates the porous medium will create a slightly asymmetrical mix zone (trailing edge stretched out), with the longitudinal dispersion coefficient approximately proportional to the first power of average fluid velocity (if composition is nearly equalized in pore spaces by diffusion). If the velocity in interstices is large enough, there will be insufficient time for diffusion to equalize concentration within pore spaces. In this region, longitudinal dispersion increases more rapidly than fluid velocity. At low velocities in interstices, transverse dispersion is characterized by a region in which transverse diffusion dominates. If the fluid velocity gets high enough, there will be a transition into a region where there is stream splitting with mass transfer but with insufficient residence time to completely damp-out concentration variations within pore spaces. There are several variables that must be con- trolled to get consistent longitudinal and transverse dispersion results, viz., (1) edge effect in packed tubes, (2) particle size distribution, (3) particle shape, (4) packing or permeability heterogeneities, (5) viscosity ratios, (6) gravity forces, (7) amount of turbulence, and (8) effect of an immobile phase. INTRODUCTION Diffusion and dispersion in porous rocks are of current interest to the oil industry. This interest arises because of the influence of dispersion on miscible-displacement processes. In a recovery process utilizing a zone of miscible fluid, there is the possibility of losing miscibility by dissipating the miscible fluid or by channeling or "fingering" through the miscible zone. Diffusion and dispersion are two of the mechanisms that may lead to mixing and dissipation of the slug. On the other hand, dispersion may tend to damp-out viscous fingers which may be channeling through the miscible slug. 58 Hence, dispersion may be detrimental or beneficial (if it prevents fingering through the miscible zone). Therefore, it is doubly important that we understand these processes. In this paper we review, summarize and interpret a great deal of information from the literature. In particular, we will briefly discuss molecular diffusion in miscible fluids. Then we will discuss what differences to expect for diffusion in a porous rock. If there is movement of the fluid through the rock, then there may be an additional mixing or "dispersion". Furthermore, the dispersion longitudinally (in the direction of gross fluid movement) and transverse to the direction of fluid movement will not be equal. We will discuss both types of dispersion as well as several variables which can affect dispersion (viscosity differences, density differences, turbulence, heterogeneity of media, etc.). This group of variables has sometimes led to difficulty when comparing literature data. DIFFUSION OF MISCIBLE FLUIDS If two miscible fluids are in contact, with an initially sharp interface, they will slowly diffuse into one another. As time passes, the sharp interface between the two fluids will become a diffuse

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger&apos;s method; (b) by Stadler&apos;s method, based on Kick&apos;s law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

By Charles E. Locke

The little stamp-mill in the mining laboratory of the Massachusetts Institute of Technology and the work done by it have been well described by Prof. R. H. Richards and E. E. Bugbee in a paper read at the Albany meeting of the American Institute of Mining Engineers, February, 1903.&apos; As run for student class-work the mill contains a feeder, stamps, plate, and vanner. Results in the past indicate that the work of these machines is just as efficient as that of a regular mill handling the same class of ore. It has been the custom to obtain ore principally from Nova Scotia, mainly because it is the nearest source of supply, and also because there is a considerable saving in freight-cost as compared with other districts. The gold in Nova Scotia ores is notoriously coarse, and for this reason it is almost impossible to obtain satisfactory results by sampling and fire-assay, unless an extremely large lot of ore is crushed and all of the contained gold pellets are saved. A very interesting and most extraordinary example of this fact has been presented by a recent run in the Technology stamp-mill. Since the capacity of the mill is about 60 kg. per hr., and since in about 5-hr. run the students in any one section have an opportunity to make the necessary study of machines, it usually happens that several runs are made from one lot of ore. When the shipment is received it is first dried and weighed, put through the Blake breaker, set at 1 or 1.5 in., and the crushed product is piled in a cone on the sampling-floor. When the crushing is completed the ore is usually stored away in barrels for future use; it is aimed to have each barrel of

Jan 1, 1914

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,&apos; Si,&apos; Ni,2-5 CO,&apos;-&apos;, Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry&apos;s law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.&apos;2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969