Search Documents

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By E. P. Jennings

(Read at the Amenia Meeting, October, 1877.) THE abundance and value of the tellurium minerals of Colorado is well known, but, as yet, few analyses have been made of them, and I offer these as a small contribution to the chemistry of these valuable ores. 1. Native Tellurium.-The specimens from which the analyses of this mineral were made are from the "John Jay" Mine, Boulder County, Colorado, where it occurs in quite large masses, though mixed with more or less silica and iron pyrites. It is usually a fine¬grained, tin-white mineral, but sometimes occurs in distorted, hexag¬onal prisms in cavities in the quartz. Before the blowpipe it gives the reactions for tellurium, sulphur and iron; by cupellation, it yields a small amount of gold. An analysis of a coarsely crystallized speci¬men gave the following results

Jan 1, 1878

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley's paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80's are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg's 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By Renato G. Bautista, Robert A. Hard

A comparative study has been made of the ex-tractability of several of the transitim metals from thiocyanate sohtions using methyl isobutyl ketone as the organic solvent. Extractions were made of scandium (III), chromium (III), manganese (II), iron (III), and cobalt (II), of which only the scandium , iron, and cobalt were readily extracted. All extractions were made at pH 2 and at 25.5 °C. A series of extraction experiments was made on scandium, iron, and cobalt to determine the effect of thiocyanate cmcentration added as the ammonium and also as the calcium salt. Also determined was the effect of metal ion concentratim and ionic strength on the distribution ratio. Analyses of the organic extracts indicated the scandium and iron were extracted principally in the uncharged trithiocyanate form, while the extractable form of the cobalt contained the cobaltotetrathiocyanate anion. THE chemical separation of metal complexes in solution by solvent extraction has in recent years been developed for large scale separation as well as bench scale work in the laboratory. It has also found increased application in analytical chemistry. Its extension to extractive metallurgy as a unit operation is best illustrated in the recovery of uranium and vanadium from their leached liquor.5-8 The extractability of some thiocyanate systems have been extensively investigated. The rate earths have been separated from one another using butanol as a olvent. Scandium was effectively extracted in ethyl ether using ammonium thiocyanate as the com-plexing agent.'' Similarly, the separation of hafnium from zirconium has been reported using ether""' or hexone13 as the organic solvent. The extractability of various metal thiocyanates in ethyl ether is given by 0ck.l Sharp and Wilkinson15 prepared nickel-free cobalt slats by thiocyanate extraction. The mechanism of extraction of titanium (IV) thiocyanate with methyl isobutyl ketone was determined by elafosse.''" The characterization of cobalt (TI) thiocyanate complex using methyl isobutyl ketone as the solvent at near neutral aqueous solution and the spectrometric studies of the ex-tractable cobalt complex has been made by Hard." It is noteworthy to mention at this point that the fundamental characteristic of ketone (oxonium) solvent extraction is that the extractable species are uncharged ion pairs solvated by the ketone molecules, but probably still partially hydrated.

Jan 1, 1963

By A. E. Lehman

A RECENT demand for some form of panoramic display of an important railway line, showing its branches, connections, and terri tory controlled by it, revealed to the writer the advantages of' a topographical model or relief map fix this purpose. Hitherto, maps of this nature have been used chiefly for scientific and geographical purposes, and confined to a comparatively narrow field of service. They deserve to become more popular and to have their advantages better understood. Much has been written and accomplished in this direction by Prof. Lesley, Messrs. Harden, Moulten, de Mendonca Cortez, and others; but I believe their pub lished descriptions of the methods employed in the construction of these models are confined to those used by themselves. It is the writer's aim to present in condensed form these various methods, and some suggestions of practical value as to the most economical course of procedure, as well as to mention some of the uses that may be made of the results obtained Methods of Construction.—Many different materials have been prepared and used in the preparation of relief maps, such as metal, clay, plaster, gypsum, wax, putty, Card-board, papier-mache, wood, and compositions of varions kinds, with results more or less success ful : wood, however, in the writer's experience, has been found to be by far the most satisfactory, combining the advantages of stability, accuracy and ease of handling. The following is a brief description of several of the methods used in constructing topographical models : When clay, wax, putty, compositions or materials of a plastic nature are used, the operator carries his work up from its base by means of measurements or by the eye, manipulating and shaping the material as best he can, ac cording to such features of his subject as he wishes to delineate. This process requires remarkable skill, and given this, will probably fall short even then of an approximation to accuracy; lacking essential elements of detail nil over the work and exactness, particularly in position and elevation of the most important points in the territory mapped. When either of the above mentioned materials or compositions are used, metal or wooden pins are sometimes driven into the base or level datum plane of wood, the top of these pins giving the eleva-

Jan 1, 1886

By J. Richard Kyle

Lead-zinc ore bodies in the upper part of the Pine Point carbonate barrier complex are localized in paled-solution structures that developed as the result of post-middle Givetian subaerial exposure. Detritus-filled dolines host prismatic ore bodies, and macropores and stratabound permeable zones contain tabular ore bodies. Sulfides are concentrated in these transgressive paleosolution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition, perhaps related to periodic supply of reduced sulfur. District and ore body metal distribution pattern may reflect the nature and movement of mineralizing fluids.

Jan 1, 1981

By Walter Kauenhowen

GeRmany's crude-oil production during 1936 totaled 3,112,494 bbl., an increase of 5.2 per cent over the 3,007,711 bbl. produced in 1935. The official monthly production figures published in 1936 report only the individual production figures of the three old established fields, whereas since 1936 official reports combine the production of all other fields into one figure. According to these published data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1936 was as follows:

Jan 1, 1937

By F. S. Sinnatt

THIS paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to playa definite part in the spontaneous combustion of coal in the goaf (waste).

Jan 3, 1925

ARTHUR H. STORRS, Scranton, Pa.-I would like to ask whether this same process is applicable to bituminous coal? FELLS A. VOGEL, New York, N. Y.-This Dutch process is applicable to bituminous or any other kind of coal. The Berwind Fuel Co. has had a plant in operation, in Superior, Wis., for about 2 years, using the Dutch process, and it has made a very satisfactory briquette, using Pocahontas coal. There is just one item in Mr. Frey's paper I would like to discuss; that is, the matter of cost. Mr. Frey figures a total cost of $3.35, based on the use of 7 per cent. of oil. Of course, the price of oil has advanced seriously within the last year or two, and any possible reduction in the percentage of oil required in the manufacture of briquettes is very important. I believe that Mr. Frey will agree that very good briquettes can be made with considerably less than 7 per cent. of oil; in fact, actual experience has shown that it can be clone with less than 5 per cent. The only possible effects of a low percentage of oil, particularly in anthracite briquettes, are that the briquette might not burn so freely, and that it might not be quite so hard. Briquettes made by the Lehigh Coal & Navigation Co., using 7 per cent. of binder, are extremely tough. Those briquettes have been handled in one of the local yards in Brooklyn, chuting them from railroad cars into boats and digging them out by grab buckets, and the losses average less than 2 per cent. This compares very favorably with domestic anthracite coal, with which the losses from breakage amount to between 7 and 10 per cent.

Jan 4, 1918

By T. B. Massalski, Horace Pops

The occurrence and the temperature dependence of the athermal martensitic transformation in bcc Cu-Zn ß-phase alloys have been studied by cold-state microscopy, differential thermal analysis, and electrical -resistivity measurements. CinenzatograpJzic studies have shown that in the majority of alloys the transformation occurs in two stages. A thermoelastic phase, having a 'needlelike" uppearance, forms initially at the MS temperature and grows relatively slowly, chiefly in the edge (lengthwise) direction. With further cooling, an additional martensitic phase forms in rapid bursts at a lower temperature, MB, Both martensitic phases appear to have the same cry stallographic habit hut their modes of formation and growth are different. For the composition range studied, between 38.55 and 41.49 wt pct Zn, the habit planes determined are close to the (2.17 ,12) plane of the matrix, in general agreement with the prediction of the phenomenological theory of martensite formation. Thermal cycling through the MB temperature produces permanent plastic deformation in the 0 matrix and gradutally eliminates the typical burst phenomena. Thermal cycling only through the MS temperature produces no noticeable deformation effects. THE bcc Cu-Zn ß-phase alloys tend to become unstable at low temperatures and undergo a martensitic transformation,'-3 but the details of the transformation have not been completely determined. Following earlier metal log raphic and X-ray work1 Tichener and ever' determined by means of electrical-resistivity measurements the temperature range of the martensite transformation during continuous cooling. The transformation temperature was found to decrease with increasing zinc content, becoming about -130°C for an alloy containing 40.04 wt pct Zn. Hull and Garwood3 made a metallo-graphic study of Cu-Zn 0 brasses at temperatures down to -160°C, and determined the habit plane of the transformation product for an alloy containing 38.88 wt pct Zn. No metallographic studies below liquid-nitrogen temperatures have been reported. The martensitic transformation in ß-brass alloys can also be induced by deformation.1,4 The MD temperature corresponding to the appearance of the strain-induced martensite is some 300°C higher than that observed without strain, and hence the transformation can be strain-induced in alloys containing a higher percentage of zinc. Massalski and Barrett4 found that alloys containing as much as 51.89 wt pct Zn could be transformed into a faulted hcp structure by cold working at liquid-helium temperature. Because the details of the MS temperature and morphology reported in the literature are somewhat incomplete, a further study has been made of some of the above features. A design of a cryogenic stage for optical metallography5 has permitted the examination of specimens at temperatures down to 4.2oK, and the use of a cinecamera has permitted a study of the morphology on cooling and heating. The particular aim of the present work was to examine the transformation temperatures, the habit planes, and the growth morphology over a wide composition range in the ß-phase field. The effect of thermal cycling upon the subsequent transformation was also examined.

Jan 1, 1964

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By R. H. Hopkins, R. W. Kraft

X-ray and metallographic analysis reveal that the preferred cryslallograPhic relationships in direc-tionally solid~fied Pb-Sn eutectic specimens can be stated: interface growth direction, Experiments in which tin single-crystal seeds were used to nucleate the eutectic demonstrate that the normal lamellar structure observed at steady state can be forced to break down initially to a semide-generate structure when the crystallograPhic direction of the tin seed does not lie within the preferred eutectic interface plane. A normal structure eventually develops by preferred grain growth. X-ray topo-graphs and rocking curves substantiate that the perfection of eutectic samples increases as growth proceeds until steady-state conditions prevail. RECENT years have seen substantial progress made in the understanding of eutectic solidification through both intensive theoretical1'' and experimental investigations (see Ref. 7 for a review and extensive bibliography of both aspects). Several important observations concerning the nucleation and growth aspects of binary eutectic solidification have been brought to light. Briefly some of these include the nonrecipro-cal nucleation of one phase upon another,'j9 the tendency for a specific low-index direction of one or both phases of the eutectic to be aligned in the growth direction during unidirectional solidification,'0711 and the production of lamellar microstructures having a preferred interface plane between "11-13 phases. Questions quite naturally arise as to the mechanism by which preferred grain growth evolves during eutectic solidification and what relationships (if any) connect the initial nucleation of one phase upon another with the preferred growth directions and interface planes observed after a few centimeters of growth in many systems. This study was initiated in an attempt to answer these questions. An experiment was devised in which both the nucleation and growth steps in the crystallization of a binary eutectic, Pb-Sn, could be correlated with subsequently developed eutectic morphology and crystallography. This was accomplished by nucleating the eutectic upon a tin single crystal seed and then causing the eutectic to grow from the seed by directional freezing. The morphology of the structures produced in this manner was then monitored metallographically and the orientation relationships and substructural perfection determined by X-ray analysis. The information thus ob- tained was correlated to the growth history of the samples. EXPERIMENTAL DETAILS The eutectic of composition 38.1 wt pct Pb and 61.9 wt pct sn14 was prepared by accurately weighing lead and tin of 99.999+ (from ASARCO and Lytess Metals and Chemicals, respectively), melting in a clean Pyrex beaker under an argon blanket, and casting into the proper crucible for resolidification as described below. Tin seeds were grown by the method of ~halmers," saw-cut, oriented by the Laue method, and soldered to the pull rod of the Czochralski puller. All seeds were given a final electropolishing (to assure the removal of any deformed material from the cutting operation) and acetone degreasing immediately prior to the nucleation experiment in which they were to be used. Eutectic samples were unidirectionally solidified in a horizontal graphite boat1' or by pulling from the melt16 with tin (or graphite) seeds. A flowing argon atmosphere was employed in all experiments and growth rates and temperature gradients, constant for a given run, varied from 2 to 4 cm per hr and 8" to 15°C per cm over the course of all the experi-

Jan 1, 1969

By Edward Halse

The occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:— I. They have been washed in from the surface, or from an upper portion of the vein.. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. TV. They have been formed in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. * I. Boulders and Pebbles which have been Washed in from the Surface, or from an Upper Portion of the Vein. In this type it is presupposed that the vein at one time communicated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoet, in France. " Toutes les parties tendres du filon de Pranal ou ces phenome'nes sont les plus prononces ont 6th excaves jusqu'a d'aasez grandes profondeurs par I' impetuosite des torrents, qui out depose la matiere alluviale.'"

Jan 1, 1906

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

R. W. Balluffi (Atomic Energy Div., Sylvania Electric Products Inc., Bayside, N. Y.)—Since porosity is known to form in the copper side of Cu-Ni couples during diffusion24,25 it is of importance to consider this factor in interpreting the large variations of chemical diffusivity with copper concentration reported for this system. The presence of porosity may affect the measurement of D in two ways: 1—density changes in the couple invalidate the usual solutions of the diffusion equation, and 2—the pores may act as short-circuiting paths when transport through the vapor or along internal surfaces is appreciable or else as open circuits when these effects are small. The error produced by the first effect may be estimated by a graphical analysis. Fig. 8 shows the porosity generated in the copper side of the Kirkendall interface of a pure nickel vs pure copper couple after diffusion for 350 hr at 1040°C in hydrogen. In Fig. 9 the actual diffusion curve which would be obtained by the usual slicing technique is shown as a solid line drawn to the same scale (from the data of da Silva and Mehl"). The amounts of porosity (obtained by lineal analysis) and of nickel are graphically represented by the hatched areas. The standard solutions of the diffusion equation are valid only when all volume elements of unit length and unit cross section contain equal numbers of atoms." It is possible to correct the experimental curve to satisfy this condition by shrinking the couple in the direction of diffusion in such a way as to eliminate the porosity.* The corrected diffusion curve obtained after

Jan 1, 1954

Covering resources, production, uses, defense impact, and future outlook of nickle, Mining Engineering presents the third in a series of articles on strategic minerals. Preceding it are "Cobalt" in January and "Sulphur" in May.

Jan 8, 1951

By William E. Newman

When Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great and the tonnage was small, but on the other hand the results were fairly satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Rozan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process. The Luce and Rozan process has persisted in its original form to the present day. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process. Out of many schemes he decided that this could be accomplished by placing the Luce and Rozan kettles upon hydraulic rams so that each

Jan 1, 1918