Search Documents

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By H. N. Eavenson

In a discussion in the Transactions of the Institute (vol. Xl, page 835 et seq.) the writer gave some data about the explosions of gas and dust in the coal mines of the United States, Canada, and Mexico…

Jan 1, 1915

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.'- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers' have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.' The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.' The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954

The plan for establishing relations of American industry with national labor on a definite basis so closely follows the channels of the efforts of Engineering Council, principally in the classification and compensation work, that it is of special interest to the engineering profession. The principles laid down under the following headings are about to he submitted to a referendum vote of the membership of the Chamber of Commerce of the United States. These principles were prepared by a special committee of the Chamber of Commerce after a long period of study of the entire subject of industrial relations. 1. Industrial enterprise, as a source of livelihood for both employer and employee, should be so conducted that due consideration is given to the situation of all persons dependent upon it. 2. The public interest requires adjustment of industrial relations by peaceful methods. 3. Regularity and continuity of employment should be sought to the fullest extent possible and constitute a responsibility resting alike upon employers, wage earners, and the public. 4. The right of workers to organize is as clearly recognized as that of any other element or part of the community. 5. Industrial harmony and prosperity will be most effectually promoted by adequate representation of the parties in interest. Existing forms of representation should be carefully studied and availed of in so far as they may be found to have merit and are adaptable to the peculiar conditions in the various industries. 6. Whenever agreements are made with respect to industrial relations they should be faithfully observed. 7. Such agreements should contain provision for prompt and final interpretation in the event of controversy regarding meaning or application.

Jan 6, 1919

By H. J. R. Way

The work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recom- mendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. History OF the Field The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies8 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1946

By H. J. R. Way

The work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recom- mendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. History OF the Field The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies8 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1946

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By Lester Uren

WITH the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described.

Jan 9, 1925

By Bernard York, John J. Reed

J. P. Zannaras (U.S. Tungsten Corp., Congress, Ariz.) —In the investigation described in the paper by Bernard York and John J. Reed, the 8x8x8-in. square block was subjected to compressive forces from three sides, top, side, and rear. Let us refer to the stresses set up by these forces as Sz due to top pressure, Sy due to side pressure, and Sx due to rear pressure. At the section across the 2-in. hole (when failure occurred at 317 psi) the compressive stress Sy was equal to 317 x 8/6 = —422 psi, the top compressive stress S; is of the same intensity, —422 psi, and the rear compressive stress S, equals —317 psi. The true stress is T = Sy — S — S Taking as 0.2,* Taking the case when the opening was ½ in. and failure occurred at 517 psi, 8 Sy - 517 x -----= —537 psi 7.5 8 Sz = 517 x-----= —537 psi 7.5 Sx = —517 psi The true stress T = Sy — Sz — S, T - —537 + 0.2 x 537 + 0.2 x 517 = —327 psi. It can be shown that the above fundamental formula holds good not only for the above two examples but for all sizes of openings used, because when this formula is expressed in terms of the external pressure and size of the opening it agrees perfectly with the experimental results obtained by the authors and given in Fig. 12 of their paper. General formula: T = Sy — s: — S....

Jan 1, 1955

By R. D. Irving

THE object of the present paper is to give an outline account of the mineral resources of the State of Wisconsin, so far as they are now known, including both metallic ores and non-metallic useful mineral substances. The only previous publication making any attempt at such an account is one of a popular nature, prepared by the writer for Snyder and Van Vechten's Historical Atlas of Wisconsin, which was published at Milwaukee in 1878. The data upon which the statements of the following pages are based are chiefly from the

Jan 1, 1880

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By J. L. O’Brien, M. Suenaga, K. M. Ralls, V. F. Zackay

The effecls of aging a1 400°C on tile resistive transition at 4.2°K of a superconducling 70Zr-30Nb alloy are reporled. Microstrclural changes were studied by critical temperature, resistiue critical field, residual resistiuily, and microhardness measurements and by X-ray diffraction, optical microscoby, ad replication electron microscopy. The result of the aging treat- A defect-free Type 11 superconductor in a magnetic field above Hc1 cannot sustain a transport current runt is a fine array of w-phase pavticles with a mean center to center interparticle spacing of about 800A. At an aging time of 300 hr the maximum onset critical current density is rcached. The particle size at the maximum current density if about 4202. At times longer than 300 hr effective particle impingement leads to lower onset critical current densities. perpendicular to the applied field without power loss in the sample.'-3 This power loss is due to flux line motion caused by the Lorentz force and is manifested by a longitudinal voltage.4-6 When defects are present in the material, flux lines are pinned until the Lorentz force exceeds the "pinning force". That is, it is thought that flux lines reside in free-energy wells existing at the defects, and the critical Lorentz force is that which when integrated over distance will supply the free-energy difference necessary to move the flux

Jan 1, 1968

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Alden B. Greninger

In a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form {133}. In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form (110), and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices arc body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc were deformed and examined micro-

Jan 1, 1938

By Alden B. Greninger

In a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form {133}. In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form (110), and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices arc body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc were deformed and examined micro-

Jan 1, 1938

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe’s Minerals Corp.’s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5m3 (300 cu ft) lead and zinc

Jan 1, 1980

By E. M. Elkin, J. H. Schloen

All known methods of treating and recovering the various components of copper refinery slimes are discussed. The slimes treatment processes presently used by five copper refineries are described and flowsheets are given. A bibliography is appended. THE recent increase in anode copper production at the Noranda smelter placed an additional load on the Montreal East plant of Canadian Copper Refiners Limited. The consequent increase in the amount of anode slimes led to a careful consideration of the various methods of slimes treatment. A critical review of these methods is presented here in the belief that it would be of interest to copper refiners. No such review has yet been published, although a number of individual flowsheets have been described. To make the information of greater value, a questionnaire was sent to all copper refineries. While the overall response to the questionnaire was not entirely satisfactory, the foreign refiners gave much detail in their answers and expressed willingness to cooperate further if needed. Although the data below do not cover all refineries, it is thought that examples of all flowsheets currently in use are included. A comparison of these flowsheets should prove of interest. The paper is divided into two parts. One part deals with a discussion of all known methods of treating and recovering the various components of the slimes. The second describes the processes now in use at various copper refineries for the treatment of raw slimes up to the production of Doré bullion. A brief description of the two main electrolytic methods of parting Doré bullion is appended. Since the first commercial application of electrolytic refining of copper by J. B. Elkington in 1865, the treatment of anode mud or slimes has undergone many changes. The object of treating slimes has always been the recovery and separation of precious metals. With the passage of time, increasing attention has been paid to improvement in recovery and quality of byproducts, mainly selenium and tellurium. The original methods of treatment were crude, although relatively direct. For example," the slimes were fused on a dolomitic clay bed in a reverbera-tory furnace; the slag was removed and the resulting metal cupelled to silver and gold. In another process, the dried slimes were oxidized and scorified on the lead bath of a cupelling furnace. Later, these pyrometallurgical methods were modified by sulphuric acid leaching, followed by fusion with niter in a reverb eratory furnace. A preliminary oxidizing roast improved the leaching step. Straight hydro-metallurgy has not found practical application. No matter what method is employed, the result is Dorb metal—a silver-gold alloy, with or without the metals of the platinum group. Characteristics of the Slimes Anode slimes are made up of those components of the anodes which are not soluble in the electrolyte. They contain varying quantities of copper, silver, gold, sulphur, selenium, tellurium, lead, arsenic, antimony, nickel, iron, silica, etc. The color of raw slimes is grayish black and the particle size is —200 mesh. However, Baraboshkin and Gaev (Ref. 1, p. 37), describe light gray colored slimes from the electrolysis of secondary copper which are composed predominantly of sulphates and of basic salts. In anode furnace practice primary and secondary metals are not usually segregated and such slimes do not commonly occur. Copper in the slimes originates to a large extent in the cuprous oxide of the anodes and is therefore dependent on the oxygen content of the latter: Cu2O + H2SO4 + CuSO4 + H2O + Cu [I] Opinions have been expressed that some of the copper is formed by decomposition of cuprous to cupric sulphate Cu2SO4 ? CuSO4 + Cu PI The product of either reaction is very finely divided. Depending on the slimes composition, much of the copper is combined with sulphur, selenium, tellurium, etc. The balance of the copper is in the free metallic state.

Jan 1, 1951