Search Documents

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

By R. W. Smith

IN the manufacture of portland cement, the basic and fundamental essential is a limestone uniformly rich in calcium carbonate and carrying less than 3 per cent magnesium carbonate. In searching for such a deposit, also having in mind quantity of rock, accessibility and quarrying facilities, the Pacific Coast Cement Co. discovered and developed its present quarry at View Cove on the east coast of Dall Island, Alaska. Dall Island is about 100 miles west of Ketchikan and 650 miles north from Seattle. It is 70 miles in length and 5 to 10 miles in width. The climatic conditions are much more favorable than would be expected. The temperature ranges from zero to 70 degrees. The precipitation is considerably more than at Seattle, although there was less snow during the last season than at Seattle. The island is rugged and mountainous; the vegetation is moss and grass and a large portion is timbered with spruce, hemlock and cedar. Some of this timber has market value. The limestone quarry is about 30 miles north of the extreme southern end of the island. The company acquired 240 acres which contain limestone of remarkable uniformity, the percentage of calcium carbonate being about 95. It is estimated that there is ample recover- able rock on the holdings to supply the cement plant at its maximum capacity for well over 100 years.

Jan 1, 1929

By AIME AIME

IN A STATEMENT summarizing general conditions in the Federated American Engineering Societies, the executive secretary, L. W. Wallace, expresses the belief that the Federation has made substantial progress. At the annual meeting of the American Engineering Council, to be held in Washington Jan. 5 and 6, this progress will be shown by reports covering activities in many fields. "Unquestionably," says Mr. Wallace, "the Federa¬tion has made favorable and permanent contacts in Washington. Through the, activities of Congress and of the new Federal administration. we have had the opportunity to render some really constructive service. We feel, however, that the great body of engineers are not adequately informed of the organization of the Federation, of its aims and purposes and of its activities.

Jan 1, 1921

By Robert V. Whitman

INTRODUCTION Ideally, this paper should start by citing examples of slope failures in open pit mines during earthquakes. I do not know of any such examples, although - since my search of the literature has not been exhaustive - such examples may well exist. However, there certainly are many examples of devastating earthquake-induced landslides, and there is no reason why such landslides cannot occur at large open pits. Moreover, many of the actual earthquake-induced landslides have seriously affected mining operations in one way or another. Hence, this paper will treat earthquake-induced landslide phenomena in general, in the hope and expectation that the reader can apply this general knowledge to the specific problems associated with open pit mining. Ultimately, of course, the aim is to predict the likelihood of the occurrence of earthquake-induced landslides, and to delineate steps which can be taken to minimize the possibility of their occurrence. These aims can be achieved only imperfectly at the present time, for our knowledge concerning earthquake-induced landslides is still in an embryonic stage. Nonetheless, much useful knowledge does exist. In order to understand and apply this knowledge, it is necessary to: 1. Review the nature and extent of actual earthquake-induced landslides; 2. Have a grasp of the basic terminology and concepts of seismology; 3. Study the fundamentals of probability-based seismic risk analysis; 4. Appreciate the way in which earth materials behave during earthquake loadings; and 5. Have a general knowledge of the methods currently available for analyzing the dynamic response of slopes. Much of this paper is devoted to this necessary background. Information of practical use in connection with various classes of slope stability problems is assembled in the final sections. LANDSLIDES DURING PAST EARTHQUAKES Almost every earthquake in mountainous country, strong enough to be reported in the literature, has caused at least some landslides and rockfalls. Unless these slides or falls damage

Jan 1, 1971

By Bernard York, John J. Reed

J. P. Zannaras (U.S. Tungsten Corp., Congress, Ariz.) —In the investigation described in the paper by Bernard York and John J. Reed, the 8x8x8-in. square block was subjected to compressive forces from three sides, top, side, and rear. Let us refer to the stresses set up by these forces as Sz due to top pressure, Sy due to side pressure, and Sx due to rear pressure. At the section across the 2-in. hole (when failure occurred at 317 psi) the compressive stress Sy was equal to 317 x 8/6 = —422 psi, the top compressive stress S; is of the same intensity, —422 psi, and the rear compressive stress S, equals —317 psi. The true stress is T = Sy — S — S Taking as 0.2,* Taking the case when the opening was ½ in. and failure occurred at 517 psi, 8 Sy - 517 x -----= —537 psi 7.5 8 Sz = 517 x-----= —537 psi 7.5 Sx = —517 psi The true stress T = Sy — Sz — S, T - —537 + 0.2 x 537 + 0.2 x 517 = —327 psi. It can be shown that the above fundamental formula holds good not only for the above two examples but for all sizes of openings used, because when this formula is expressed in terms of the external pressure and size of the opening it agrees perfectly with the experimental results obtained by the authors and given in Fig. 12 of their paper. General formula: T = Sy — s: — S....

Jan 1, 1955

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe’s Minerals Corp.’s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5m3 (300 cu ft) lead and zinc

Jan 1, 1980

By C. H. Jr. Herty

THE removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal, or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath.

Jan 3, 1925

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By A. M. Gaudin

A GREAT number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,2 involves the effects of electric charges at the surface of the minerals particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable.

Jan 1, 1927

By O. W. Ellis

IN VIEW of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal in the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metallic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone are used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt.

Jan 1, 1930

By T. N. Williamson

6.3-1. Historical Development. Rotary drilling has been used in surface mining for many years. Its principal use is for primary blasthole drilling. In this use, holes in the range from 4 to 15 in. in diameter are drilled in overburden and massive ore bodies for large initial blasting operation. With properly designed shot patterns and loading, secondary blasting is seldom required. The use of rotary drilling with diamond bits for exploration is discussed in Chapter 3.1. Small rotary drillholes of approximately 2-in. diameter are employed as blastholes to shatter uncovered coal seams, but this is a minor part of surface mining drilling operations. Another minor use of rotary drills in surface mining is for placing wire saw poles in dimension stone quarries, usually accomplished with large-diameter calyx or steel shot drills. Primary blasthole drilling by the rotary method was performed with drag bits until 1949 (19). Its use in mining was only in soft formations, so that rotary drills prior to that time were found principally in overburden drilling for the surface mining of coal. In 1949 it was found that air circulation to remove cuttings resulted in increased penetration rate and prolonged life for the rolling-cutter type of bits. Prior to that time, and since their introduction in oil well drilling in 1907, water had been used for circulation with these bits. The dependence on water to clean the hole had delayed the acceptance of bits with rolling cutters in mines because of water haulage and freezing problems as well as the loss of water through cracks in the formation. After rolling cutters were introduced, subsequent improvements in tools made rotary drilling adaptable to harder formations (18). This system is now used in the hardest formations encountered in mining. 6.3-2. Principles of Operation. ENERGY. Rotary drills attack rock with energy supplied to the bit by a rotating drill stem, and infrequently by

Jan 1, 1968

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By Sarat C. Rubra

Geographically, British India includes India or Hindustan proper, Burma, and a part of Beluchistan. In ancient times India occupied a very important position anlong the producers of minerals and metals; in fact, as late as the middle of the seventeenth century, it contributed a very considerable quota of the mineral and metal supplies of the world. The branches of the industry worthy of special note are gold, silver, lead, antimony, copper, iron, diamonds and other precious stones. The famous " Damascus steel" was originally manufactured in India, Damascus being only a mart; and it is interesting to note that even at the present time this product is still made in India. Prior to the discovery of diamonds in Brazil in 1728, India was the sole producer of this important mineral; and while no diamond-mines are now systematically worked, fine specimens are occasionally reported to be found in river-beds and in alluvial diggings. For ages, nearly all of the minerals of present commercial value have been produced and worked in India, and many of the deposits may still play an important part in the world's mining and mineral history. Despite the patient work of the ancient Indians, the limited knowledge they possessed of pumping and ventilation precluded the possibility of attaining any great depth in mining. Under special conditions, shafts have been sunk to 600 ft., but the average depth was much less. As a result of this limitation, the ancient miners confinecl their work to the available ores in sight, leaving large bodies of ore intact, which can be profitably worked with modern methods of mining. As an evidence of this statement may be mentioned the mines of the Kolar gold-fields in Mysore, which have reached in some shafts a. depth exceeding 2,400 ft. Traces of ancient work in these

Jan 1, 1904

A SERIES of papers on strategic and otherwise important mineral products was prepared some ten years ago under the joint auspices of the Committee on Foreign and Domestic Mining Policy of the Mining and Metallurgical Society of America and the Committee on Industrial Preparedness of the American Institute of Mining and Metallurgical. Engineers. These papers were later published in a joint volume entitled International Control of Minerals (1925). Amongst them was one on manganese. The Subcommittee on Manganese prepared its paper in two forms. One was intended for inclusion with the series above referred to and approached its subject more particularly as an international problem. The other dealt more definitely with manganese as an element in the problem of national defense. This last was first written under date of January 24, 1924 as a confidential report, for and at the request of the War Department. It was later released and published, in slightly modified form, as a separate pamphlet by the Industrial Preparedness Committee of the American Institute of Mining and Metallurgical Engineers. After the lapse of eight years, in view of the vital position of manga-nese in the problem of industrial preparedness against a war emergency, the War Department made a request to have the conclusions of 1924 reviewed and brought up to date. To comply with this request the manganese subcommittee was reconvened (with a somewhat changed personnel) and exhaustive studies were once more made of the entire subject of manganese. A new report, with specific recommendations, was submitted to the War Department in February, 1932. This second report is now herewith released for publication. Certain specific conclusions and recommendations as expressed to the War Department are omitted. Otherwise the report stands as prepared and submitted by the manganese subcommittee of 1931. The members of this committee were: C. Minot Weld, Chairman, R. C. Allen, Arthur S. Dwight, J. W. Furness, D. F. Hewett, Reno H. Sales, Theodore Swann and Scott Turner. ARTHUR S. DWIGHT, Chairman, Committee on Industrial Preparedness.

Jan 1, 1933

The plan for establishing relations of American industry with national labor on a definite basis so closely follows the channels of the efforts of Engineering Council, principally in the classification and compensation work, that it is of special interest to the engineering profession. The principles laid down under the following headings are about to he submitted to a referendum vote of the membership of the Chamber of Commerce of the United States. These principles were prepared by a special committee of the Chamber of Commerce after a long period of study of the entire subject of industrial relations. 1. Industrial enterprise, as a source of livelihood for both employer and employee, should be so conducted that due consideration is given to the situation of all persons dependent upon it. 2. The public interest requires adjustment of industrial relations by peaceful methods. 3. Regularity and continuity of employment should be sought to the fullest extent possible and constitute a responsibility resting alike upon employers, wage earners, and the public. 4. The right of workers to organize is as clearly recognized as that of any other element or part of the community. 5. Industrial harmony and prosperity will be most effectually promoted by adequate representation of the parties in interest. Existing forms of representation should be carefully studied and availed of in so far as they may be found to have merit and are adaptable to the peculiar conditions in the various industries. 6. Whenever agreements are made with respect to industrial relations they should be faithfully observed. 7. Such agreements should contain provision for prompt and final interpretation in the event of controversy regarding meaning or application.

Jan 6, 1919

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940