Search Documents

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By H. Reinhardt, P. Haglund, J. Rydberg, B. Lunden

As legislation to minimize pollution in effluent streams becomes stricter, it is important to treat used acid pickling baths before discharge. This is usually achieved by neutralization of the acids and precipitation of the dissolved metals in such a way that neither acids nor metals can be re-used. A process has been designed and tested on a pilot plant scale to recover both acids and metals from a stainless steel pickling bath leaving only Na2SOs in the effluent. In this process, H2SOr is added to the spent pickling liquor and the recovery of the pickling acids HN03 and HF is achieved by solvent extraction, using TBP in kerosene as the organic solvent. The extracted acids are stripped with water, giving an acid concentration high enough for direct use in the pickling bath. Molybdenum is also extracted by TBP and is recovered in a separate step. The other metals, Fe, Cr and Ni, are precipitated from the raffinate as hydroxides, dried and recycled to the metal process. In evaluating this process, comparative experiments with mixer-settler and pulsed column have been performed. The process described is being considered for use by a Swedish company pickling 70,000 tons per annum of stainless steel.

Jan 1, 1973

By E. H. Cho

INTRODUCTION Activated charcoal has been used for several centuries in many capacities including the recovery, isolation and purification of various materials (1). The first use of charcoal in a gold metallurgical system was in the extraction of gold after chlorination (2, 3,4). The gold was dissolved in a chlorine system and subsequently filtered through charcoal. The application of charcoal with cyanide extraction was patented by Johnston (5) in 1894 and adopted commercially in Australia in 1897. The process consisted of dissolving the gold and silver in a potassium cyanide solution and passing it through a series of charcoal filters. The charcoal was subsequently smelted to recover the gold and silver. The interest in the use of charcoal diminished in the first part of the twentieth century as the practice of the use of zinc as a precipitating agent increased. However, in 1916, the Yuanmi Mine in Australia replaced their zinc precipitation plant with a charcoal adsorption plant. In 1926, Scott and Gross (7) of the U. S. Bureau of Mines con- ducted extensive research on the adsorption of gold and silver from cyanide leach solutions. Among their findings was the result that the most important factor in improving the adsorptive power of charcoal was heat treatment with oxidation by air or steam. The work of Zadra (8) in 1952 stimulated renewed interest in the use of activated charcoal in gold and silver recovery with the development of a method of recovery of the gold and silver from the charcoal other than its destruction by burning. The process involved simultaneous desorption

Jan 1, 1983

By Charles W. Wright

At most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bulldozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners' are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1937

By Anton Sawatzky, Erich Vogt

By means of mathematical solutions to the appropriate diffusion equations, we describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various temperatures and concentrations encountered in a heavy water moderated reactor. When the hydrogen concentration is below terminal solid solubility only the a Phase is present. Redistributions are then described in terms of the characteristic functions of the difhsion equation. For higher concentrations both the a and 6 phases are present. We assume the two phases to be always in equilibrium. For moderately small hydrogen concentrations exact solutions of the two-phase equation approach the the approximate solutions derived by Sawatzky and for all concentrations the exact solutions exhibit the qualitative features of his result: the two-phase concentration increases with time, everywhere; in the absence of a hydrogen current at the hot end of the sample an a-phase region always exists there; the interface of the a + 6 , a-phase boundary moves toward the cold md of the sample and the hydrogen concentration is discontinuous at the interface. Simultaneous solulions of the a and a + 6 hydrogen distributims and of the concomitant interface motion are obtained and compared to the observations of Sawatzky and Markowitz. The kinetics of the hydrogen diffusion process are shown to lead to m apparent heat of transport of the a phase which is lower than the actual value (even for samples with long anneals) thus resolving at least partially the disparity between experimental measurements of this quantity. A number of recent papers1"4 have reported measurements on the diffusion and redistribution of hydrogen in Zircaloy-2 under temperature and concentration gradients. These studies were instigated by problems arising from increasing use of Zircaloy-2 as a fuel element cladding material in pressurized-water power-reactors. The Zircaloy-2 picks up hydrogen during the operation of the reactor: the consequent precipitation of zirconium hydride in the Zircaloy-2 has pronounced effects on its mechanical properties. The Purpose of the present Paper is to describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various hydrogen concentrations and temperatures likely to be encountered in reactors. When the hydrogen in the Zircaloy-2 is entirely in the solid solution phase (a phase), the differential equation for thermal diffusion is well known and the redistribution can be described by standard mathematical methods some of which are given in Section 11 below. The treatment of the a + 6 (hydride) region differs from the earlier treatment of sawatzky3 by taking into account several modifications of the two-phase diffusion equations as suggested to us by Markowitz4 and Kidson.5 Even with the modifications the results obtained in our more complete treatment are substantially the same as those found by Sawatzky. As we show, the difference between the results of sawatzky3 and kIarkowitz4 is largely due to the difference in the geometry of their experiments. In the next section we derive the modified two-phase equation for arbitrary geometry. The exact solution of this equation is given in Section III for linear and cylindrical geometry. It is shown that Sawatzky's approximate solution is quite accurate for almost all the temperatures and hydrogen concentrations which are actually encountered. In Sawatzky's approximate theory the hydrogen concentration everywhere in the two-phase region increases continuously. As his paper pointed out, this result, together with hydrogen conservation, implies that in a sample with no hydrogen current flowing into the hot end a two-phase region is always accompanied by a single-phase region at the hot end of the sample. The net hydrogen gain in the two-phase region is supplied by the decrease of hydrogen in the single-phase region and by the movement of the (a, a + 6) boundary toward the cold end of the sample. Hydrogen conservation at the (a, a + 6) boundary leads to a discontinuity in the concentration and its derivative there. In Section IV it is shown how these qualitative features of the thermal diffusion kinetics arise from the simultaneous solution of the a-phase differential equation and a + 6 phase equation. Methods derived by us previously for the solution of the redistribution in both phases and the accompanying motion of the boundary are used to obtain approximate solutions valid for large times. The solutions account well for the observed redistributions of Sawatzky and Markowitz. It is shown how the continuing motion of the (a, a + 6) boundary leads to measured values of the heat of transport lower than the actual value, even for specimens with relatively long anneals.

Jan 1, 1963

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

The Students' Organization of the Michigan College of Mines was recognized as an Affiliated Student Society by the Board of Directors of the Institute, at a meeting held on April 28, 1916. At the College of Mines, University of Washington, 30 students and instructors took part in the annual spring excursion early in April. Studies were made of the new reverberatory and casting furnaces at the Tacoma smelter, the Du Pont powder works located on Puget Sound and the Britannia Mining and Smelting Company's mine and mills on Howe Sound, near Vancouver, B.C. The Britannia mills are using Hancock jigs, Burchart tables and Minerals Separation flotation cells to effect a high recovery on low-grade chalcopyrite ore. The Mining Club, University of. Wisconsin, elected the following officers for the second semester of the present school year: J. G. SKIRM, President, H. L. RAU, Vice President, T. C. SHERWOOD, JR., Secretary-Treasurer, H. E. HODGSON, Mucker, , F. M. WOLVERTON, Assistant Mucker. Theo. C. SHERWOOD, Jr., Secretary.

Jan 6, 1916

By D. M. Blacknall, N. N. Winogradoff, E. W. Williams

Low-temperature measurements of photolumines-cence were used to evaluate the progvess in materials development. Variation of the impurity type, impurity concentration, and method of growth were used to clarify the chemical origin of defects in GaAs. Melt-g~ozun, epitaxial vapor-, and solution-grown samples were studied. A comparison of measurements at 77" and 20°K shows that more defects can be observed at the lower temperature. Th'vee residual defects were identified in relatively pure GaAs. These were: silicon, copper, and a gallium vacancy-donor complex. Solution growth from a gallium solution inhibits the formation of the latter two. Eleven defects were studied and the "optical" activation energy of some of these, namely, silicon, cobalt, and chromium, has not been reported in the literature before. THE discovery of the injection laser in 1962 prompted extensive measurements of the photoluminescence of GaAs. The measurements were made at 77°K on GaAs doped with shallow impurities at various doping levels and compared with electroluminescence1'2 and absorp- tion data.374 In addition, lower-temperature studies were made on relatively pure GaAS' and on GaAs doped with oxygen,5'" manganese,' and copper.' The observation of defects* in GaAs with photolu- *The word "defects" ~efers to both chemical impurities and native defects. minescence at low temperatures makes photolu mines-cence an invaluable tool in evaluating the progress in materials development. The only previous evaluation was done at 77°K when solution-grown and melt-grown GaAs were compared.O No identification of defects was made but it was shown that some of the deep-level luminescence seen in melt-grown GaAs was absent in solution-grown GaAs. The present work extends the comparison of preparation techniques to lower temperatures and to a study of epitaxial vapor-grown GaAs. It is particularly valuable for thin epitaxial layers since they cannot be analyzed by conventional analytical techniques. In addition, by varying the impurity type and impurity concentration the chemical origin and nature of defects in GaAs was demonstrated. Eleven defects were studied in all. Three of the defects were identified as residual defects which often contaminate GaAs prepared from the melt and the vapor. Only one such defect was observed in GaAs grown from a gallium solution and this was identified as silicon.

Jan 1, 1968

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By Carl H. Schmuck

The terms "cable bolting," "extended ground support," and "grouted cable" are synonymous, and they have been popping up with much more regularity in the mining engineer s vocabulary. In simplest terms, lengths of u itensioned cable up to 18.3 m (60 ft) are grouted in drill holes prior to mining. This permits radical departures from mining practices that rely on conventional rock reinforcement. For example, by placing a pattern of cable bolts in the back of an open stope, ore can be mined in successive slices. After each slice is taken the protruding cable; are simply cut off and mining proceeds. When about 4.6 m (15 ft) of reinforced back remains, a crew places a new par tern of cable bolts in the ore.

Jan 12, 1979

By A. B. Dyes

In the operation of a water-driven reservoir, a free gas saturation can he established by maintaining production rates fast enough to cause the reservoir pressure to decline below the bubble point. The benefit of such a procedure on the displacement efficiency of the oil by water is illustrated for two types of sandstone samples from one reservoir. Those rock samples showing the poorest recovery to water drive in the absence of a free gas saturation give the most improvement in the presence of a free gas saturation. Employing one type of reservoir fluid (low .shrinkage) the benefit of evolved gas on oil displacement is calculated at several reservoir pressures below the bubble point. This demonstrates the presence of air optimum pressure for water displace,rnent which is .several hundred pounds per .square inch below the bubble point. Displacement of oil at the optimum pressures results in the removal of 7 to I? per cent more oil than would be obtained by displacement at the bubble point pressure. In some instance. this magnitude of increase may be worthy of consideration in establishing the maximum efficient rate of production from many water-driven fields. INTRODUCTION For many years the belief that the use of gas could be combined with that of water to result in a better recovery operation than the use of either of these phases alone has been prevalent in the oil industry. This is evidenced by the several field trials which have employed the injection of gas and water in combination.1.2.v In most cases the small amount of any additional recovery, in combination with the limited knowledge available on the older reservoirs, has left uncertain the influence of gas on recovery in these earlier attempts to combine the use of gas with water. Research studies in recent years have demonstrated through laboratory. floods the magnitude of the benefit of the presence of gas on the displacement of oil from sandstones by water.5,6,7,8,9,10,11 In addition, studies of the distributions of the phases which are present during the displacement process have developed concepts concerning the mechanism by which this benefit is obtained."." It now remains for the engineer to incorporate these findings into the general technology of reservoir operations. It is the purpose of this paper to illustrate that the production of a water-driven reservoir at pressures below the bubble point is one such operation whereby improved oil displacement efficiency can be obtained as a result of gas evolution. The establishment of a gas saturation by evolution of dissolved gas was one of the techniques used by several investigators in the laboratory studies. The possibility of obtaining the benefit of gas evolution in water-driven reservoirs by producing at pressures less than the bubble point has 3150 been pointed out previously." The desirability of this operation has undoubtedly

Jan 1, 1955

By George L. Atwood, William Brown

Phosphate ore is being mined at Monsanto Co.'s Henry mine, near Soda Springs, Idaho, for the company's three furnace elemental phosphorus plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. In stripping and mining, D-9 crawler tractors are utilized to rip and push-load rubber-tired scrapers. The equipment consists of six D-9G crawler tractors, four Caterpillar 657B scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12- month basis, two shifts per day, whereas mining is mainly in the summer months on a one-shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1 million tons of phosphate rock and 2.5-3 million cu yd of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor which owns, operates and maintains all equipment used. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis.

Jan 8, 1972

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By F. C. Langenberg

DURING the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point: The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the. bars was tested in this manner and in no instance could any difference in structure be detected between the three specimens.1

Jan 2, 1915

By Howard Eavenson

PRIOR to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and was usually used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia-which was then regarded as the standard coking and gas coal of the coun, try, and the best coal available anywhere for these purposes. With the advent of the by-product oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for cokemaking, gas and other metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than the best of the coal from the Pittsburgh seam, or than any northern coal, and in by-product ovens produce coke that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these seams is shipped in great quantities without beneficiation and is lower in ash and sulfur than the best washed product from any seam mined in the north.

Jan 1, 1932

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

JEROME ALEXANDER.-All of you undoubtedly know that a microscopic examination of metals will reveal many things; but we should go further than just simply using a low- or medium-powered- microscope and seek the reason why grain size varies under different conditions. When we get below the limits of the ordinary microscope, we enter the so-called colloidal field, which means that we are dealing with aggregations of matter that approximate, say, 100 millimicrons. The colloidal dimensions average approximately 50 millionths of a millimeter and extend down to about 3 µµ. This, of course, is beyond the range of visibility in the ordinary microscope. Just to give you an idea of this matter, if 1 cu. in. of platinum is reduced to a sheet five molecules thick, it will cover 7 acres; you can imagine the amount of surface involved when metal, or anything else, is subdivided to so high a degree. Of course five molecules thick is a little below the limits of the colloidal dimensions. The statement is made in the paper that "metals and alloys might be

Jan 4, 1919

Meeting of Mar. 26, 1915.-The following Committee on Nominations was appointed: Fred W. Bradley, Chairman; James F. Kemp, Past President; Frank M. Smith, Chairman Montana Section; R. C. Gemmell, Chairman Utah Section; Frank A. Ross, Chairman Columbia Section; Louis S. Cates, Arthur Thacher. The Committee on Precious and Base Metals and the Committee on . Coal and Coke were appointed, the personnel of which is shown in another part of this Bulletin. The President was authorized to appoint a Committee on Welfare with J. Parke Channing as Chairman. W. P. Cutter, Librarian of the United Engineering Societies' Library, was appointed a representative of the Institute on-the Committee oh Classification of Engineering Knowledge to co-operate with similar committees of other engineering societies. A vote of thanks was extended-to Edward B. Sturgis for his excellent work in arranging for the Annual Dinner. in February, of this year. The suns of $57.30 was appropriated to the New' York Section. It was resolved that in response to the courteous invitation from 36 members of the Institute in Arizona and the neighborhood, the 1916 summer meeting of the Institute be held in Arizona.

Jan 5, 1915

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959