Search Documents

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By W. A. Sheaffer

Electric furnace installation and tough-pitch copper-casting operation at Canadian Copper Refiners Ltd. are described. General layout, power supply and control, refractories, induction pour hearth, casting equipment, metal temperature control, and oxygen-content control are discussed. E LECTRIC furnace at Canadian Copper Refiners Ltd. was put into operation in August 1949. The installation was designed primarily to melt electrolytic copper cathodes and to produce vertically cast tough-pitch shapes. To meet emergencies during reverberatory furnace shut-downs, provision was made for casting horizontal tough-pitch wire bars. Due to the ease with which metal temperatures, melting rates, oxygen content, and casting hours can be altered to suit production demands, the electric furnace has met the requirements admirably. General Layout The plant has been described by H. S. McKnight' and by J. H. Schloen and E. M. Elkin.2 Since these papers were written, the electric furnace has been installed in a 140 ft extension of the original casting building. The extension, 264 ft in width, is divided into one 24 ft and four 60 ft bays, each a continuation of similar bays in the older building. Fig. l, a partial floor plan of the extension, shows the location of major equipment. Power Supply and Control Power for the electric furnace and its auxiliary equipment is delivered by Quebec Hydro over two 12 kv three-phase, 60 cycle pole lines. One line is in use, while the second serves as an emergency standby. Connections for the electric furnace from these lines, which also feed the refinery power house, are made to a substation on Canadian Copper Refiners Ltd. property. Connections between this substation and the furnace transformer room are in underground conduit. The are-furnace transformer, 550 v auxiliary-equipment transformer, and 12 kv switchgear are in the transformer room near the furnace. Stepdown from 12 kv to are-furnace voltages is done by a 7500 kva oil-immersed water-cooled three-phase 60 cycle transformer. This unusually high kva rating is available because the arc furnace and transformer were adapted from a steel-melting unit. Secondary voltages are available in 16 steps between 251 and 95 v (across phases). A four-position tap changer, operated from the furnace switchboard is connected to taps yielding 199, 164.5, 127, and 115 v, respectively. The transformer primary feeder is equipped with a General Electric Magne-Blast circuit breaker. The pour hearth, casting wheel, bosh conveyor, and other auxiliary equipment are fed by a 12 kv to 550 v, 750 kva three-phase 60 cycle transformer. Graphite electrodes, 14 in., with tapered nipples are held in the are-furnace electrode arms with steel wedges. The arms, fed from the transformer secondary busbars by flexible cable bundles, are actuated by winch cables. Direct-current motors operating the winches are supplied by a 250 v motor-generator set. Power input to the furnace is controlled from the furnace switchboard. The board has the usual combination of remote controls for the 12 kv breaker and transformer tap changer, meters, overload relays, automatic and manual electrode motion controls, switchgear, etc. When power is on the furnace, automatic electrode feed is used; the power draw on a given voltage tap then is governed by current-limiting rheostats. The rheostats work through a Westinghouse bal-lanced-beam control circuit which, in turn, operates reversing contactors in the winch motor circuits. Arc Furnace The arc furnace is a standard-type NT Pittsburgh 'Lectromelt with inside shell diameter 12 ft 3¾ in. By hydraulic-lift cylinders, the furnace can be tilted forward to 39 ½ ° and backward to 5" from horizontal. A roof-swing cylinder is also installed but not used. Fig. 2 shows refractory-lining details. With the lining as shown, operating life between repairs is 6 to 9 months of two-shift casting operation. Charge slot, skim door, and roof refractories then are replaced completely, and any necessary repairs made to side walls. Bottom life is longer and the original under courses are still in service, while the top course was replaced in October 1951. The launder is lined with high chrome-magnesite trough brick backed by fireclay and insulating brick. The trough is covered with fireclay brick and asbestos sheet. At intervals, openings 12x6 in. are left in the permanent covering. These are covered with

Jan 1, 1956

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By D. L. Harris

Chemical upgrading testwork on Stillwater chomite concentrate shows that reduction roasting and leaching (sulfuric acid and/or ferric sulfate) can provide upgraded feed to ferrochromium furnaces for making upgraded ferrochromium. Two-stage reduction smelting in electric arc furnaces can make upgraded ferrochromium also. Sulfating roasts and leaching (acid and/or water) results using gaseous SO2—SO3 or solid ammonium sulfate were not satisfactory for upgrading chromite. Chemical upgrading of domestic Stillwater (Montana) chromite has been considered at various times1'2' to provide a material with higher chromium to iron ratio, more like foreign high grade ore, for the production of standard grade ferrochromium. Physical bene-ficiation of Stillwater chromite ore can provide a ratio, Cr/Fe, no higher than the ratio in the chromite mineral, which is approximately 1.7. For comparison the analyses of a foreign metallurgical grade chromite ore, a high grade electrostatic process Stillwater concentrate and a stockpile concentrate from the Stillwater ore are noted in Table I. Single stage smelting of the high grade foreign ore with a ratio, Cr/Fe, of 3.37 can provide a ferrochromium of over 65 pct chromium content. Similar smelting of the Stillwater concentrate with a ratio of 1.7 can provide a ferrochromium of 50 to 55 pct chromium content.' It has been demonstrated on a pilot plant scale that chemically upgraded Stillwater chromite having a ratio, Cr/Fe, of 3.0 also can be smelted to provide a ferrochromium containing over 65 pct chromium.5 Two major considerations for an upgrading process are the ratio, Cr/Fe, in the product and the chromium recovery. A minimum ratio, Cr/Fe, of 3.0 is required in the product but for economic reasons a higher ratio is desirable for blending purposes as long as the recovery is satisfactory. Data from different kinds of chemical upgrading testwork are presented in this report. Some of the testwork was conducted to make a product which was not intended to be feed for ferrochrome smelting, but the data are considered pertinent to chemical upgrading. Results reported by others are noted also for comparison. WORK REPORTED BY OTHERS The U. S. Bureau of Mines has contributed much to the literature on chemical upgrading of chromite and a summary is given in Table 11. Reduction roasting and acid leaching were reported by Boericke and Bangert,1 by Lloyd and Gorst, et a1,2 and by Boericke3 to demonstrate very good success on a laboratory scale and only fair success in pilot plant tests for Stillwater (Benbow) concentrates. This work included basic studies on thermodynamic properties to explain the reduction and leaching results. Canadian workers, Downes and Morgan,9 have reported experimental success in upgrading a low grade Bird River chromite, similar to Stillwater material by the same process. Russian workers1' have noted results on reduction tests of high grade chromite which may apply to low grade ores and which help in understanding the reduction process. The use of flux additives in the reduction process was an innovation of their work. The Canadian workers9 also reported other kinds of experiments, including autoclave leaching of the chromite in a limited amount of sulfuric acid. An insoluble basic chromium sulfate was formed and separated from soluble iron, magnesium, and aluminum sulfates to provide an upgraded material. U.S. Bureau of Mines workers, Lloyd, Rosenbzum, Home and Davis,' reported on autoclave leaching of Benbow concentrates as a means of obtaining chromium alum for electrolysis. This last work required selective crystallization of alum to separate iron from chromium. Chloridizing roasting of Benbow and Mouat concentrates has been reported by Hunter and Banning6 and others8 to show that the iron chloride could be volatilized from the chromite to provide upgraded residues.

Jan 1, 1964

By C. E. Mills

Studies of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations. Geology and Structure1 The ore deposits of the United Verde are of the massive sulfide, schist-replacement type. A structural anticline formed by the intrusion of diorite between bedding planes of steeply dipping and severely folded greenstones and porphyry localized the deposit of sulfide. The mineralized zone is of great horizontal extent varying from 200,000 to 400,-000 sq. ft., and extends from the surface to the lowest levels at a steep dip of from 50° to 75. The irregular interfingering of the sulfide with

Jan 1, 1934

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934

Jan 1, 1929

By S. I. Liu

THE effects of strain histories, consisting of several prestrains in opposite directions, on the flow and fracturing characteristics of metals determined in a final test have been investigated previously.'" Such strain histories vary from a single prestrain in tension or compression to the number of strain cycles leading to fatigue failure.' Between these two limits, various strain histories could be visualized and some can be attained readily. One such example is a strain history consisting of a first prestrain in tension of various magnitudes and a second prestrain in compression also of various mag-nitude. In this investigation the strain history was extended to the combination of these two limits, i.e., a single prestrain in tension or compression followed by balanced strain cycles of a selected magnitude e, = k0.12. It was found in this case that only compressive initial prestrains could be investigated with sufficient accuracy.* Such strain histories can be considered also as (low cycle) fatigue tests of a metal subjected to various amounts of cold working. It appears from previous publications that cold working within a wide range of reductions usually raises the un-notched fatigue strength of many metals.'-' This effect, however, has been found to be inconsistent and sometimes reversed for other metals?.7 Furthermore, Ludwik reports that the yield strength of cold-worked specimens may be reduced by cyclic strains, while that of materials without cold work is generally increased in the initial cycles." " In addition to the above tests, a study was made of the effect of intermediate re-solution heat treatment on low cycle fatigue behavior. Such anneals should eliminate the strain hardening induced by the cyclic strains. As far as their effect on the fracture characteristics is concerned, a few previous tests seemed to indicate that the damage resulting from cyclic strains is retained only partially after heat treatment." A further investigation was made in which one specimen was subjected to repeated unbalanced tension cycles in which the strain interval was approximately $ 0.013. This repetition of plastic tension damages the material slightly. This result appears to confirm Ludwik's observations." " Commercial 3/4-in. rod of the aluminum alloy 24ST4 was selected for this investigation. The material was subjected to the following treatments before machining: 1—Re-solution treatment at 920" ± 10°F for 45 min, 2—water quench at room temperature, and 3—aging for four days at room tem-perature.? The treated material then was machined to desired specimen contour and tested. A coolant was used during machining to minimize any artificial aging effects of heating during machining. In some cases the 24ST4 specimens were reheat treated after having been strained. In these cases, the heat treatment was the same as the re-solution heat treatment described above. Procedure As shown in Fig. 1, threaded end specimens with a minimum diameter of 0.266 in. and a contour radius of 2 in. were used for prestraining to an axial compressive strain ranging from 6, = —0.10 to E, = —0.48. For large prestrains, two consecutive corn-

Jan 1, 1952

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

The four papers making up this symposum have been prepared especially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathematical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismograph exploration campaigns would do well to become familiar with as much as possible of the technical aspests of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1940

The four papers making up this symposum have been prepared especially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathematical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismograph exploration campaigns would do well to become familiar with as much as possible of the technical aspests of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1940

By H. F. Silliman, Daniel R. Hull, John R. Freeman

IN the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of coldwork and a considerable number of anneals. This condition has been disturbed by the prep0nderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2: 1 brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. HOT-ROLLED 2:I BRASS For illustration, therefore, a typical cake of hot-rolled 2: 1 brass has been chosen. This was rolled to a slab 7/8 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. 1. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it w0uld be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Stephen Taber

Introduction.............................. 62 Asbestiform Minerals.......................... 63 Chemical and Mineralogical Relations............... 63 Physical Properties........................ 64 Types of Asbestos............................ 65 Origin of the Fibrous Structure...................... 66 Views of Previous Investigators.................... 66 Discussion of the Evidence.................... 67 Conclusions........................... 69 Origin of Cross-fiber Veins....................... 71 Chrysotile Veins......................... 72 Structural Features of Cross-fiber Veins............... 78 Veins of Crocidolite and Other Fibrous Amphiboles........... 83 Origin of Slip-fiber........................... 84 Origin of Mass-fiber........................... 86 Discussion............................... 87 IntRoduCtion The term asbestos, as commonly used, includes half a dozen minerals all having a well-developed fibrous structure, but differing in chemical composition and in some of their physical properties. In its strict application the name is limited to the fibrous varieties of the monoclinic amphiboles. Commercially, however, the most important of the asbestiform minerals is chrysotile, a fibrous variety of serpentine. About 95 per cent. of the asbestos used in manufacturing is chrysotile, and it commands a much higher price than any of the other fibrous minerals now on the market. Although the production of asbestos has increased rapidly in recent years, comparatively little has been published concerning its origin. The present paper is preliminary in its nature, and therefore does not pretend to exhaust the subject. The ideas herein developed are the result of field investigation, laboratory experiments in the growth of fibrous

Jan 1, 1918

By Luther Lennox

DURING the last few years, one of the great problems in the milling of all ores has been that of crushing. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of crushing to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of crushing methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative crushing resistances of a number of ores now being milled in this country and Alaska, the management of the Portland mills requested samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh . screen; in the screen analyses tabulated and plotted herewith, the 150 mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves.

Jan 8, 1918

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By Frank L. Nason

(New York meeting, February, 1912) IN the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States, 1,100,000,000 Great Britain, . 1,000,000,000 Germany, 2,200, 000, 000 Spain, 500,000,000 Russia and Finland, 1,500,000,000 France, 1.500, 000, 000 Sweden, . 1,000,000,000 Austria-Hungary, . 1,000,000,000 Other countries, 1,200,000,000 Total, . 10,000, 000, 000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at the present rate of consumption. On the other hand (according to Edwin C. Eckel,1 from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the, next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates arc definitely, but by no means finally, given for the United States District. Tons. Lake Superior District, . . 1,500,000,000 to 2,000,000,000 Alabama, red hematite. . . 1,000,000,000 brown hematite, 725,000,000 Georgia, red hematite, 200,000,000 brown hematite, 125,000,000 Tennessee red hematite, . 6110,000,000 I brown hematite, 225,000,000 Virginia., red hematite, 50,000,000 brown hematite, 300,000,000 Total, . . 4,725,000,000 to :5,225,000,000

Jul 1, 1912