Search Documents

By R. E. Collins

The existence of fluid migration across fixed boundaries in oil and gas reservoirs has been known for many years. Several techniques have been developed in the past for estimating The rate of migration across fixed boundaries as an aid in planninng field development and in the valuation of oilfied properties. The principal de/errc7nt to the use of these techniques lies in the rather extensive reservoir and field data required for ca1cula1ion.s of fluid migration. For this reason, a new, simplified procedure has been developed which makes possible the calculation of fluid migration with a minimum of field and resrvoir data. This new technique is based on certain. solutions of the differential equations describing flour in the reservoir which assume, for the portion of the reservoir of interest, that the formation can be approximated by a homogeneous rock of uniforrn thickness, that only a Single mobile fluid phase exists, and {hut fluid production at the well is solely a result of expun.rioti of rile resersoir fluds. The results of the, present work are compiled in a set of curves. These curves can he used to calculate both rule and cummulative fluid migration when the abovc assumptions ore ju.r/ifiril. The only data required for such calcu1ations are the production hisrories of all wells in the field, the permeability and porosity of the reservoir., the, compressibility and viscosity of the fluid. and the shape of the reservoir, INTRODUCTION The migration of fluids across fixed boundaries in oil and gas reservoirs has long been recognized as an engineering and economic problem, but no methods for estimating the extent of migration during the development stage of a reservoir have been published. The investigation reported here has been directed toward providing a simple technique for estimating the extent of such migration and has therefore been restricted to the simple case of a homogeneous reservoir of uniform thickncss containing compressible liquids. It is assumed that only a single mobile fluid phase exists and that fluid production at the wells is solely by expansion of the reservoir fluids. Obviously, few, if any. reservoirs conform to these assumptions during their entire productive life. On the other hand, most reservoirs approximate fluid expansion reservoirs during their initial stages of primary production. Consequently, the present work should be applicable during the field development of most reservoirs, regardless of whether or not they ultimately are gas cap, dissolved-gas, or water-drive reservoirs. The mathematical analysis of this problem has been outlined in the Appendix, while the results of the investigation are presented in the following discussion. DISCUSSION OF CALCULATION PROCEDURE SLNGLE Well, Ini-iimite Reservoir The procedure for calculating fluid migrations is based on solutions of the partial differentia1 equations describing the flow of a homogeneous compressible liquid in a homogeneous reservoir of uniform thickness. This differential equation has the form of the well-known diffusion equation. The equation, as applicable to our problem, is where p is fluid density, is porosity, EL is viscosity, c is compressibility,* and k is permeability; .r, y and t are the space coordinates and time. Derivation of this equation is given in the Appendix. The analytical solution of this equation for a single well of negligible radius producing at a constant rate. q, from a reservoir of infinite areal extent for a time, 1. can he readily obtained. From this solution the rate of flow and also the cumulative flow across a straight line segment of length, 1, at a perpendicular distance. 6. from the well can be computed. One end of the line must be on the perpendicular joining the well to the

By E. N. Pugh, J. V. Craig

WhILE it has been established that well-defined microhardness impressions can be produced in germanium by room-temperature indentation,1-3 the role of dislocations in the process is the subject of continuing discussion.4-7 Recently, Carroll and ~anaka'

Jan 1, 1969

Jan 1, 1971

By Charles White Merrill

Money is one of the most .pervasive elements in human life. The compensation for a workman's daily efforts is expressed as a wage and is measured in money. What an individual may consume depends largely on his income which also is expressed in terms of money. If he would start an enterprise its size would be determined in large part by the amount of money available for capitalization and its success would be measured in net income expressed in money. In short, the most widely used common denominator for comparing merchandise, real property, jobs, enterprises, gross national product, or personal success is money. Despite this use of money by almost everyone past infancy to express his appraisal of the in- numerable values he sees around himself, the complexity of the device called money makes its nature and workings a mystery to most users. Some of the difficulty in understanding money results from the fact that it has three distinct but interrelated functions: (1) a medium of exchange, (2) a unit of account, and (3) a store of value. In many statements about money the discussion moves from one function of money to another without the speaker or the listener recognizing the changes. For example, the housewife says "We took the money we had saved up to make the down payment and after twelve monthly payments the television will be ours." When this housewife spoke of "saving up the down payment" she referred to money in its function as a store of value; when she spoke of "the down payment" she was using money as a medium of exchange; and when she referred to the "monthly payments" she spoke of money as a unit of account. Another cause of confusion in understanding money is its paradoxical nature in that it represents both the power to produce and the power to consume. For example, when the rich uncle dies one nephew may regard his inheritance as an opportunity to buy a farm and leave the ranks of the wage earners to become an independent producer, whereas the other nephew may regard his portion as the means of living in complete leisure as a pure consumer.

Jan 1, 1959

Jan 1, 1963

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By Michael Tenenbaum

THE importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1947

By Wayne E. Glenn

The San Miguelito Field of Ventura County, California, lies along the coast approximately five miles northwest of the city of Ventura. The structure is one of several in the Ventura anticline, a series of anticlinal folds trending northwest-southeast through the San Miguelito Field. The Ventura Avenue Field lies to the southeast along the anticline, and Padre Canyon and Rin-con Fields lie to the northwest; the series then extends beneath the Pacific Ocean. Production is obtained from the Lower Pico and Repetto formations of Pliocene age, and oil accumulation is controlled by faulting, lithology and structure. The first well in the First Grubb Pool was completed in November, 1931, and to date 48 producing wells have been drilled on the 276 productive acres. Approximately 685 ft of net pay are contained in the eight sand bodies grossing 1,220 ft of section. Production of oil to date has been 15,-600,000 bbl. A gas injection project was instigated in April, 1940, but was discontinued in September, 1949. This paper is confined to a discussion of the development and performance history of the First Grubb Pool of the San Miguelito Field. LOCATION AND GEOLOGY The San Miguelito Oil Field is located in Ventura County about five miles northwest of the city of Ventura along the coastal highway to Santa Barbara. It is located within sections 23, 24, 25, and 30 of Township 3 North, Range 24 West, San Bernardino Base and Meridian. Surface elevation in the field ranges from sea level to plus 1,200 ft, and the terrain is extremely rugged. The structure is well defined on the surface and on the wall of the Amphitheatre Canyon where appears a so-called "text book" anticlinal section. The San Miguelito structure is an asymmetrical, elongated anticline about two miles long and three-fourths of a mile wide. The trend of the axis of the anticline is northwest-southeast. Fig. 9 illustrates the contours and major faults of this structure. Dips on the southwesterly flank average about 40 degrees, whereas the northeasterly flank ranges from 60 to 75 degrees. There are several faults striking generally east and west. These faults do not appear to affect materially the area of accumulation or performance behavior. It is believed that accumulation was affected by steeply dipping beds and extremely low permeability of the northeast flank of the structure. As shown by the typical log, Fig. 1. the San Miguelito Field is divided into two stratigraphic producing intervals. The First Grubb Pool comprises the interval from the "G" to "L" markers; the Second Grubb Pool from the "L" to "M" markers. The First Grubb Pool, ranging in thickness from 1,105 to 1,680 ft, with an average of 1,220 ft, includes approximately 685 ft of oil-bearing sands. The First Grubb zone consists of eight sand intervals separated by shales. The shale bodies separating the eight sand intervals within the First Grubb Pool are continuous throughout the major part of the structure and serve as an effective barrier. Many of the thin, irregular shale or siltstone streaks within these sand bodies are discontinuous and do not affect well performance appreciably. The productive horizons in the First Grubb Pool are siltstones and sandstones of the Lower Pico and Repetto formations of Pliocene age. It is apparent from inspection of the typical log that the "G" to "L" interval might have been separated into at least six producing zones and selectively pro. duced. Unfortunately the electric log and some of our modern tools were not available or were in their infancy dur. ing the period 1931 through 1937. Not until 1937 when eight wells had been completed were there sufficient geological data to permit definition of the sand bodies. Then the problem of reservoir control in this multiple-sand field, where all sands are open to a common

Jan 1, 1950

By R. C. Hall

The magnetic anisotropy and magnetostriction of single crystals of alloys between 25 and 59 wt pct Co in Fe have been determined in the disordered and ordered states. The magrzetostriction is large and positive for all alloys in both states of order (up to 150 x 10-6 for A,, and 40 x 10-6 for 111). The magnetic anisotropy becomes zero rzear 41 pct Co for the disordered state. Ordering shifts the zero-anisotropy composition to about 50 pct Co. COBALT-iron alloys have for many years been of interest as magnetic materials because they have unusually high magnetic saturation values.' This interest was increased recently by the development of Supermendur.' Supermendur is an alloy of 49 pct Co-49 pct Fe-2 pct V* which was found by suitable purification and heat treatments, including a magnetic anneal, to possess excellent magnetic properties. These included a square hysteresis loop with a low coercive force and a high magnetization, and a low total loss. Two factors which are important in determining the magnetic hysteresis properties are the basic magnetic properties of magnetostriction and anisotropy. Alloys having zero anisotropy and zero magnetostriction show improved hysteresis properties.3 Since very meager data4-' are available in the literature on the single-crystal anisotropy and magnetostriction of the cobalt-iron alloys, the present program was undertaken to determine these two properties in the disordered and ordered states. EXPERIMENTAL TECHNIQUES Ingots of the cobalt-iron alloys containing from 25 pct to 59 pct Co in iron were vacuum melted from electrolytic iron and cobalt of 99.9 pct purity. The ingots were cooled at a rate of about 1°C per hr through the transformation temperature (950" to 980°C dependent on the alloy content) for the growth of large grains. From these grains, single-crystal disks were fabricated with either the (110) or (100) plane parallel to the faces of the disk. The crystals were given two heat treatments to produce either the ordered state (cooling rate of 20°C per hr from 850 "C) or the disordered state (water quench from 850 °C). Since the iron-cobalt alloys order very rapidly, the water quench may not have produced complete disorder in all cases. Due to the method of growth, the crystals were not perfect. Most of the samples had low-angle boundaries and a few had some small included grains. These imperfections could and probably did affect the accuracy of both the magnetic anisotropy and magnetostriction measurements. Much of the scatter in the data may be attributed to the crystal imperfections. The methods of determining the spontaneous saturation magnetostriction and the anisotropy have been previously described.419110 MAGNETOSTRICTION The magnetostriction in the [loo] and [Ill] directions (hO0 and ?111 respectively) is illustrated in Fig. 1 for the disordered state. Both ?100 and ?111i became large positive values as cobalt was added to iron. The state of order did not have a large effect on the magnetostriction. The effect of order did not appear too consistent in these data. Tentative curves are shown in Fig. 1 for the ordered magnetostriction near the FeCo composition; here ?100 appeared to be lowered and ?111 raised as the degree of order was increased. These results agree qualitatively with the

Jan 1, 1961

By L. A. Cowan

IF the elements of personality be those characteristics in which humans differ, and if this definition be applied to the purchasing department for the Climax operations in Colorado, it must he concluded that this department has no distinguishing traits that would give it a departmental personality different from that possessed by the similar department of any progressive mining enterprise. Or, one may go further by stating that the rudimentary functions of any purchasing practice employed principally in the acquisition of maintenance, repair, and operating supplies are much alike, whether or not the industry involved be mining or milling. However, in the fact that the principal purchases of a mining company are materials for maintenance and repair and consumable operating supplies lies that essential characteristic which differentiates mining and milling purchasing functions from those of the manufacturer, the fabricator, or the ordinary processor.

Jan 1, 1946

By J. B. Wagner, B. Swaroop

The atomic ratios of oxygen to iron in zlarious corn-posilions of wustite in the vicinity oj the reported p to n transformation were determined in the temperalure range between 950" and 1250°C. For these conditions, equilibrium vacancy concenrations have also been determined at vatious mixtures of C0,-CO. The data show a continuos introduction of iron vacancies as oxygen is introduced into wuistite. No phase change is observed with in the wuustite field. However, the value of n in the isothermal oxygen pressure dependence, the weight change shifts to 1ower values as the concentration of oxygen increases. WUSTITE is a metal deficit semiconductor with the majority lattice disorder being cation vacancies. Using the notation similar to that of Kroger and ink,' the dissolution of oxygen into wiistite using C02-CO mixtures is represented by, WHere v+! denotes a cation vacancy with k effective negative charges and kh • denotes k electron holes, h -. Applying the law of mass action and assuming a dilute solution of defects in the wiistite yields Where the square brackets denote concentrations. Furthermore, when k = 2 the cation vacancies are completely ionized, and both the concentration of cation vacancies and the concentration of electron holes are proportional to the third root of the ratio, PC /PCo. This analysis is valid for one particular mael based on an ideal solution at elevated temperatures (in this case t > 1000°C). At lower temperatures, it has been shown2 that the pressure dependence of the electronic conductivity changes in a manner which suggests that vacancies interact with or "trap" electron holes. At the very high concentrations of defects, 10'' to 10" per cu cm, these simple models no longer hold. Recently Tannhauser,3 Geiger et a1.' Bransky and Tannhauser; and Hillegas' have found an apparent p to n transformation in wiistite in the temperature range of 950" to 1300°C. This junction was found by thermoelectric and electronic conductivity measurements. Geiger eta1.' found that the electronic conductivity became almost independent of the oxygen pressure at high temperatures and oxygen concentrations within the experimental error. In addition, Vallet, Raccah, and coworkers6'7 have reported the existence of several "varieties" of wiistite which were reported to exist within what was heretofor presumed to be a

Jan 1, 1968

By M. R. Tek, F. H. Poettmann, M. L. Grove

The general problem of single-phase natural gas flow through porous media has been considered both by mathematical analysis and field experiments. Theoretical studies on the fluid dynamics of natural gas wells resulted in derivations of expressions which permit a ber-ter understanding of the flow mechanism for conditions under which Darcy's law is no longer valid. In applying these results to natural gas production and testing technology, special emphasis war placed on the study of low permeability, slowly stabilizing formations. These applications resulted in a method of predicting the performance coefficients of tight natural gas wells. The calculation of the performance coefficient requires the determination of the "test-index", pkh/µ, the drain- age radius, R, and the effective wellbore radius, rw. Methods for estimating these parameters from field data were also developed. Field data from 15 wells were collected and analyzed. The measured values of the performance coefficients were compared with the predicted values. This statistical evaluation gave a bias of 7.14 per cent and a standard deviation of 11.6 per cent. INTRODUCTION The performance of a natural gas well is determined by the physical properties of the reservoir rock, the extent and the geometry of the drainage area, the properties of the flowing fluid, and the conditions of pressure distribution within the drainage matrix. The relation between the quantity of gas delivered and the pressure drop within the reservoir is characteristic of the behavior of each well and is often referred to as the back-pressure behavior of the well. It is well established that for normal, single-phase gas wells the relationship between the gas delivery rates and the bottom-hole pressure take, in general, the form, Q = c(P3 8 -P2 1)n. ,.......(1) where C is the performance coefficient, and n is the exponent corresponding to the slope of the straight-line relationship between Q and (P2 s, — P2 l) plotted on logarithmic coordinates. The determination of a well's performance by the back-pressure behavior not only permits the production engineers to analyze many operating problems, but also provides necessary information useful and essential to predict the future development of the field.' Important engineering and production problems such as calculation of gas deliverability into a pipeline at a predetermined line pressure, design and analysis of gas-gathering lines, determinations of spacing and number of wells to be drilled during field development to meet future market or contract obligations, etc., all depend, at least in part, on the availability and use of reliable back-pressure curves.' In the past the behavior of gas wells was evaluated

Jan 1, 1958

By Stanley Reichert

The manganese deposits of the Embree Iron Co., Embreeville, Tenn., are thought to be fairly typical and representative of the East Tennessee type of deposit, and so to warrent rather detailed description. The methods used by the Embree Iron Co. for prospecting and mining, and to a lesser extent for milling; should therefore be applicable to other East Tennessee manganese deposits, as yet' undeveloped. Early History and Discovery of Manganese Brown iron ore (limonite) was mined by the Embree Iron Co. at various times from 1890 to 1910. The early method was simply pick-and-shovel mining in open pits. Later hydraulic giants were used and sluice lines carried the ore down the mountain slopes to log washers.. During this phase of mining, manganese ore was discovered under the iron ore in some of the pits. In other areas oxidized zinc ore was found under the iron. It thus happened that the valuable zinc deposits were discovered in 1914. During the World War period, from 1914 to 1918, there was sporadic prospecting for manganese ore among the abandoned iron workings, but the main activity then centered around the recently discovered lead and zinc deposits. It was not until 1934 that manganese mining began in earnest, under the supervision of R. D. Pritchett, Mine Superintendent. Geology of the Manganese Deposits United States Geological Survey Folios 151 (Roan Mountain) and 118 (Greeneville show that Bumpass Cove is a synclinal structure thrust faulted along the southeast flank, but with normal sequence of strata along the northwest flank. Fig, l. shows the areal geology of Bumpass Cove as taken from the folios superposed on the U.S.G.S. -T.V.A. 1/24,000 topographic maps of the Erwin and Telford 7 ½ minute sheets. The manganese mines occur near the contact of the unfaulted Shady dolomite and the Erwin quartzite. This contact zone is deeply weathered, with overburden averaging 40 to 60 ft. thick. The material overlying' the bedrock along this normal contact is a very tough, plastic clay, termed "buckfat" or "ocher" by the miners. It is not a true ocher, however, in the sense of having commercial value. The manganese deposits occur along this "ocher" band. Fig. 1 also shows how the manganese deposits occur along the broad topographic terrace between the 2100 and 2200-ft. contour lines. This terrace lies at the foot the Erwin quartz ridge. Apparently it is the topographic is expression of the deeply weathered zone along the Shady-Erwin contact.

Jan 1, 1941

Jan 1, 1966

Hugh M. ROBERTS,* Minneapolis, Minn. (written discussion ? ).¬The paper by Messrs. Hall and Row marks a distinct advance in the art of diamond drilling, because it records a systematic-application of a method for directing the path of the diamond bit. Their work is an admirable example of engineering development. They had a definite object to attain; i.e., the drilling of many vertical diamond-drill holes to depths of 2500 or 3000 ft. (762 or 914 m.). They availed them-selves of a method of wedging seldom used, improved the manner of making the wedges, developed a technique of survey, and put the process into practical, continuous operation. So effectively has this been done that they determine the average cost of the work. The publication of the results, in the form of detailed diagrams, makes the application general to whoever has a similar problem. The wedging of diamond-drill holes has been practised in the Lake Superior region for the purpose of making branch holes, particularly where the original hole has penetrated a great thickness of glacial drift. The uneven nature of the iron formations has caused the results to be somewhat uncertain. One operation, in 1907, near the American mine on the Marquette Range, by the firm of Longyear & Hodge, predecessors of the E. J. Longyear Co., resulted in the drilling of a hole 1828 ft. (557 m.) deep, with two branches at depths 100 ft. (30 m.) and 770 ft; (234 m.), respectively. A second hole from the same set-up went to a depth of 2497 ft. (761 in.) with a branch at 185.0 ft. (563 m.). In this instance, the wedges were forged to the desired shapes and angles with respect to each other. A drill hole, sunk in 1915,. in the township of Bates in the. Iron River district of Northern Michigan, which penetrated 385 ft.

Jan 11, 1919