Search Documents

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1918

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 1, 1919

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.' Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.'." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By Robert Glass Cleland

IN SPITE of its widely ramified interests in manufacturing, mines, lumber, railroads, and real estate, Phelps, Dodge & Co. remained primarily interested in exporting and importing, in buying and selling, and William E. Dodge, the directing-partner, consistently styled himself a merchant. After 1849 the profits of the company mounted steadily for seven years until they approached the half-million mark, but in 1857 another severe panic ended the long period of national prosperity that had begun some fifteen years before. Extravagance, indebtedness, and inflation again took their costly toll; or, as the New York Herald of June 27,1857, declared: Governmental spoliations, public defaulters, paper bubbles of all descriptions, a general scramble for western lands and town and city sites, millions of dollars, made or borrowed, expended in fine houses and gaudy furniture; hundreds of thousands in the silly rivalries of fashionable parvenues, in silks, laces, diamonds and every variety of costly frippery are.only a few among the many crying evils of the day. The worst of all these evils is the moral pestilence of luxurious exemption from honest labor, which is infecting all classes of society. The country merchant is becoming a city stock-

Jan 1, 1952

The following list comprises the names of those persons who became members during the period May 10, 1916, to June 10, 1916: ARCHIBALD, JOHN CHRISTIE, Min. Engr., Supt. of Cyanide Plant, Guanajuato Reduction Mines, Guanajuato, Mex. BRUNEL, FRANK P., Cons. Min. Engr Mitchell & Brunel, Ajo, Ariz. CALVERT, WILLIAM ROBERT, Cons. Geol. ...225 Kearns Bldg., Salt Lake City, Utah. CHAMPION, J. R., Supt The Yak Mining, Milling & Tunnel Co., Leadville, Colo. CHARLES, LAVERN JOHN, Construction Engr., Elephant Butte Dam, Elephant Butte, N. M. CHASTEL, ANDRE, Min. Engr., Societe Miniere & Metallurgique de Penarroya, 12, Place Vendome, Paris, France. CHRISTIE, WALLACE H., Vice-Pres. and Mgr., Alt. Bert Gold Dredging Co., 604 Mission St., San Francisco, Cal. CLARK, RONALD ..Hardinge Conical Mill Co., 120 Broadway, New York, N. Y.

Jan 7, 1916

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By C. H. Li, R. J. Stokes, T. L. Johnston

Dislocation half-loops, artificially introduced by sprinkling with carborundum, were subjected to stress using three-point loading. The different stages of loop expansion and multiplication were then correlated with the macroscopic stress-deflection curve. Loop expansion started at approximately one-third of the "yield stress," defined here as the motivation stress. Above one-half of the "yield stress" simple multiplication commenced while about two-thirds of the yield stress gross multiplication developed short slip-line segments. These values were not affected by the age of surfaces exposed to both dry and wet air. Slip was not detected on unsprinkled crystals below two-thirds of the "yield stress." Thus the stress to activate intrinsic sources, defined here as the activation stress, was approximately twice the motivation stress. This relationship was independent of the strain rate used. It is concluded that lattice resistance takes the form of a viscous drag rather than a static type of force. THE importance of surface condition and environment as one of the more significant factors controlling the mechanical properties of ionic solids has recently received renewed attention.1-4 In some materials, notably the alkali halides, exposing freshly cleaved specimens to the atmosphere results in a progressive hardening and embrittlement of the crystals. This has been attributed to the surface layer becoming "aged," thereby restricting the motion of dislocations in such a way that pileup and eventually fracture results. It is necessary therefore in studying the mechanical properties of ionic crystals to inquire first into the density and distribution of dislocations in the normal cleaved surface and to understand the role these dislocations play in the onset of plastic flow. Knowledge of the effect of environment on this behavior will then assist in understanding the mechanism of embrittlement on aging. In the work reported here a method is described for studying the initiation of plastic flow from dislocation sources in the surface of magnesium oxide crystals. Preliminary results are described of the influence of surface age on this behavior. EXPERIMENTAL TECHNIQUES The magnesium oxide used in this investigation was obtained from the Norton Co. and had a nominal purity of 99.5.pct. Single-crystal specimens, having dimensions typically 1/4 by 1/8 in. cross section and 1 in. in length, were prepared by cleavage over (100) planes from the parent crystal. They were deformed under three-point loading with 3/4 in. spacing between the two end supports and a constant rate of deflection at the center of 0.001 in. per min. The maximum strain rate therefore was 1.5 X 10-5 sec-1. Reasons for choosing this particular form of loading will become apparent in a later section. In addition, a number of confirmatory type tests have been performed at higher loading rates where the maximum strain rate was increased to 1 x 10-3 sec -1. Following deformation the crystals were etched to reveal the dislocation distribution. In a previous paper5 we described a satisfactory etching solution consisting of 5 parts of saturated ammonium chloride, one part of sulfuric acid, and one part distilled water. Immersion of the crystals for 1/4 hr at room temperature developed reproducible conical etch pits at the points where dislocations emerged through the surface. It should be mentioned that dislocations freshly introduced by room temperature deformation gave sharply pointed etch pits which generally distinguished them from the almost flat-bottomed pits obtained on "grown-in" dislocations. The distinction is obvious in the photomicrograph included in Fig. 5(b). Annealing crystals at 1000°C for 12 hr on the other hand gave sharper etch pits on the grown-in dislocations and the distinction was no lower -possible; a similar observation has been reported for lithium fluoride. We have succeeded furthermore in chemically polishing magnesium-oxide crystals. Boiling in fresh 85 pct ortho-phosphoric acid for only 1 min resulted in a microscopically smooth surface which could again be etched to reexamine the dislocation distribution. This boiling time was sufficient to remove the surface damage introduced by cleavage (see next section). SURFACE DISLOCATION SOURCES There are a number of ways by which dislocations may be introduced into cleaved surfaces to act later

Jan 1, 1960

By Edmund Davenport

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned? for long periods in lamps. In these cases it was noted that the grain boundaries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits are actually small voids between the grains. The purpose of this paper is to present- the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting ?is frequently associated with poor performance of filaments in lamps. The question has arisen as to whether these intergranular pits are peculiar to tungsten, or if they occur in all metals. If they are found iii all metals, the facts will be of considerable theoretical interest, as the material at the grain boundary plays an important part in most of the current theories of the properties of metals and alloys.

Jan 1, 1927

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By George E. Aiken

Subzero temperatures of the Arctic pose some critical engineering problems for the developer and operator of open pit mines. Undoubtedly, the single most troublesome manifestation of this climate is permafrost. Underlying about 20% of the world's land area and 85% of the state of Alaska, permafrost has not only made its impact on building construction and mine excavation, but has created a legitimate threat to the delicate balance of nature existing within the Arctic environment. The recognition of permafrost areas by geomorphology and an understanding of its other complex developmental factors are the basis for two major concepts in building construction. The active method involves the eventual thawing of the complete permafrost section and is only useful in shallow areas. However, in some areas of coarse, well-drained material, vegetation may be stripped well ahead of construction and shallow permafrost allowed to method, leaves the perenially frozen ground undisturbed and is to be preferred. In selecting construction sites aerial photos may clearly reveal typical permafrost features.

Jan 5, 1972

Jan 1, 1970

(There are 70 Student Chapters in the United States, 2 in Canada) University of Alabama-University, Alabama, Mining and Metallurgical Society, Win L Mason University of Alaska-College, Alaska, Mining Society of the University of Alaska, E H Beistline University of Arizona-Tucson, Arizona, Miners Society Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, H C Gunning University of California-Berkeley, California, Mineral Technology Association, W H Somerton Carnegie Institute of Teehnology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of -Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann

Jan 1, 1956

By P. Bolsaitis, L. Skolnick

Vapor pressures of silver over ternary alloys of six different copper to gold ratios have been measured by means of the Knudsen effusion technique. The data obtained in the temperature range of 1330° to 1375° have been used to estimate the integral excess free energies of the ternary alloys and the activities of copper and gold. The results compare favorably to the predictions based on the electron cell model of alloys recently formulated by the authors. THE orifice effusion method for measuring vapor pressures of materials in condensed phases was first introduced by knudsen, and has since been used extensively for the determination of thermodynamic properties of condensed phases. The basis of the measurement is the effusion, through a small orifice, of vapor in equilibrium with a condensed phase. Assuming free molecular flow into high vacuum, the vapor pressure, P (in mm Hg), of the effusing species is calculated from the following equation:' where w (g) is the weight of effusing species lost during a run, t (sec) the time length of the run, A, (sq cm) the area of the effusion orifice, T ("K) the temperature at which the run is conducted, M the molecular weight of the effusing species, and k the Clausing factor, a constant that corrects for deviations from free molecular flow caused by the finite thickness of the orifice walls.17 The determination of partial and integral thermodynamic variables from vapor pressure data of ternary alloys is possible only if the vapor pressures of all but one component are negligible or can be esti-

Jan 1, 1969

By H. A. Davies

DURING a current program of research on the structure and properties of liquid sodium alloys, the need arose for information on the solubilities as a function of temperature of several B subgroup metals in liquid sodium. In the absence of reliable information in the literature for several of these systems, par- ticularly at temperatures in the range 100° to 300°C, an apparatus was constructed to determine solubilities by a direct melt-sampling technique, followed by wet-chemical analysis for both sodium and the solute metal. The details of the technique have been described previously.' The solubility of indium in liquid sodium was determined at eight temperatures in the range 100° to 270°C. The solubility as a function of temperature is shown on Fig. 1; this represents the liquidus line over this composition range. A cooling curve was plotted after the completion of the sampling and an arrest was observed at 94.9°C which must be interpreted as being the result of a eutectic reaction. By extrapolation of the liquidus to this temperature, the eutectic composition was estimated to be about 0.25 at. pct In. The present estimate of the eutectic temperature and composition are in good agreement with the values of 96.0° to 96.2°C and between 0.28 and 0.45 at. pct In, respectively, which were reported by Heycock and Neville.2 However, no further information on the liquidus of this system at the sodium-rich end could be found in the literature for comparison. One compound: NaIn, has been reported in this sys-

Jan 1, 1968

By Herbert Clark Hoover, Lou Henry Hoover

IN the last book I have explained the methods of delimiting- the meers along each kind of vein, and the duties of mine officials. In this book1 I will in like manner explain the principles of underground mining and the art of surveying. First then, I will proceed to deal with those matters which pertain to the former heading, since both the subject and methodical arrangement require it. And so I will describe first of all the digging of shafts, tunnels, and drifts on venae profundae; next I will discuss the good indications shown by canales2, by the materials which are dug out, and by the rocks ; then I will speak of the tools by which veins and rocks are broken down and excavated ; the method by which fire shatters the hard veins ; and further, of the machines with which water is drawn from the shafts and air is forced into deep shafts and long tunnels, for digging is impeded by the inrush of the former or the failure of the latter ; next I will deal with the two kinds of shafts, and with the making of them and of tunnels ; and finally, I will describe the method of mining venae dilatatae, venae cumulatae, and stringers.

Jan 1, 1950

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936