Search Documents

By K. E. Gray, A. Podio

ABSTRACT Berea and Bandera sandstone samples were impacted with both 3/4-in. and 1/2-in. long wedges, each having a 60° included angle and a 0.05-in. flat, at various confining pressures, with borehole and pore pressures held fixed at atmospheric pressure. Samples were saturated with air, water, glycerine-water, solirol, mineral oil and soltrol-mineral oil mixtures to obtain a wide range of pore fluid viscosity. Penetration depth was held constant at 0.1 in. Dry and soltrol-mineral oil-saturated Berea samples were impacted at depths of penetration from 0.01 to 0.04 in. under 1,000 psi confining pressure to study crater initiation. Results indicate that viscosity of the pore fluid is influential primarily during the early stages of crater formation. Differences in bit force, crater volume and blow energy for tests parallel and perpendicular to bedding were significant, but decreased as the stress state was elevated. Crater volume, blow energy and bit force were nonlinearly related with depth of penetration. Crater volume was nonlinear with energy of blow. Fixed-penetration tests on saturated Berea yielded greater crater volume than did similar tests on dry samples. Differences in the nature of deformation for low values of bit penetration were noted between saturated and unsaturated samples. INTRODUCTION Rock failure during bit-tooth impact and scouring action constitutes a vital part of the drilling process and a difficult problem for researchers. Much study has been devoted to various aspects of the problem, and much has been learned about mechanics of rock failure. However, analytical treatment of drilling at depth remains difficult, partly because there are so many factors involved and because valid simulation of downhole conditions is extremely difficult. Forming individual craters by a bit tooth or chisel impacting, or indenting, a rock mass has been studied by many investigators.1-18 Similarity between single-tooth chisel impact and the corresponding action of a rotary bit has been discussed by Appl and Gatley, Garner, Podio, and Gatlin l8 compared the similarity in single-blow impact tests with microbit drilling data reported by Cunningham and Eenink.l9 Maurerll has used single-tooth impact data to develop a "perfect cleaning" theory of rotary drilling. Individual roller cutter-tooth impact data have been reported by Young. 20 Single-tooth tests in all of the cited literature were carried out on dry rocks. Inasmuch as any subsurface rock of oilfield interest is saturated with some fluid, it seemed desirable to study crater formation in permeable rocks saturated with a viscous pore fluid as a step, however short, toward more realistic simulation of subsurface conditions. This paper presents results of single-blow chisel impact studies on Berea and Bandera sandstones, both dry and saturated with pore fluids of various viscosities at confining pressures to 10,000 psi. EXPERIMENTAL APPARATUS AND PROCEDURE EXPERIMENTAL APPARATUS The same basic apparatus for single-blow chisel impact at elevated stress states, described in earlier papers was used in this study. l6. l8 Fig. 1 shows the complete experimental system; Fig. 2 shows a cross section of the pressure cell, with a sample ready to be impacted. EXPERIMENTAL PROCEDURE Two different rocks, Berea and Bandera sandstones, were used in this study. Both rocks have been used extensively in research, and rock descriptions can be found in a paper by Gnirk and Cheatham.15 Permeability to air of Berea is about 300 md normal to bedding and 540 md parallel to bedding. Bandera had vertical and horizontal air permeabilities of 18 and 57 md, respectively.

Jan 1, 1966

By E. Ryba, D. J. Michel

SAMPLES of REZn2 (RE = rare earth) intermetallic compounds prepared by a variety of techniques have been shown to exhibit an extensively twinned micro-structure.1-4 We have recently conducted compression tests at room temperature on specimens of HoZn2 prepared by a powder metallurgy technique.' The microstructures of specimens before and after testing are shown in Fig. 1. The "before" specimen, Fig. l(a), shows the basic twin structure of this material. Fig. l(b) shows the microstructure of the "after" specimen just below the fracture surface and reveals considerable cross-twinning as well as additional

Jan 1, 1970

By Robert Glass Cleland

[DATA OF THE YEAR 1950 COMPARED TO 1909 (FIRST CONSOLIDATED REPORT) CONSOLIDATED NET INCOME Without deduction for depletion of mines $ 42,395,465 $7,337,252 After deduction for depletion of mines $ 4,112,604 $7,337,252]

Jan 1, 1952

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

Z. W. Bartlett, J. C. Carrington, H. C. Petersen and K. T. Price were elected vice-presidents of the Freeport Sulphur Co. Blandford C. Burgess was transferred on January 1 to the new Defense Materials Procurement Agency as strategic materials specialist. In May the Region III headquarters of this organization was moved to London. L. C. Campbell was elected president of National Coal Assn. Mr. Campbell, who has been a member of the National's Board of Directors and Executive Committee for many years, is vice-president of the Coal Div. of the Eastern Gas & Fuel Associates and in charge of their extensive mining operations in West Virginia, Pennsylvania and Kentucky. Vern H. Christoph has been transferred to Panama Canal Co., Marine Bureau, Navigation Division, Port Captains Office, as an admeasurer at Cristobal, Canal Zone. Eugene Cline, recently graduated from the University of Kentucky, has been employed by Pond Creek Pocahontas Coal Co., at Evanston, Ky. Sanford S. Cole, assistant manager of research at the Titanium div. of National Lead Co., received the Alumni Citation from his alma mater, Alfred University, Alfred, N. Y. This was in recognition of outstanding achievements and services in the field of ceramics which have brought honor to the institution. U. K. Custred, recently graduated from University of Kentucky, and may be reached now at Box 87, Monterey, Tenn. Robert E. Dwyer, executive vice-president of Anaconda since 1940, was recently elected president of this company and its subsidiaries, Chile Copper Co., Chile Exploration Co., and Andes Copper Mining Co. As president, Mr. Dwyer succeeds the late William H. Hoover who died in Butte, Mont.

Jan 1, 1952

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970

United Engineering Society WALTER H ALDRIDGE J VIPOND DAVIES I V N DORR Engineering Societies Library Board SYDNEY H BALL ALEXANDER C HUMPHREYS GEORGE C SLONE JOHN H JANEWVAY Engineering Foundation Board H M BOYLSTON J VIPOND DAVIES GALEN H CLEVENGER Society for Promotion of Engineering Education WILLIAM KELLY ALLEN B ROGERS American Engineering Standards Committee GRAHAM BRIGHT GEORGE C STONE GEORGE E THACKRAY Alternates-RICHARD L LLOYD and HARLOWE HARDINGE

Jan 1, 1923

By Thomas J. Crocker, Galen G. Waddell, Eugene H. Skinner

This paper describes a method of measuring initial and long-term deformations which occur in the medium surrounding mine accessways, and discusses the importance of this type of measurement in assessing support-problem areas. Delineated are (1) description of the rock-deformation monitoring equipment, (2) results of two field tests which monitored rock deformation around 4-foot-diameter raise bores, and (3) a numerical-analysis (finite-element) technique to correlate theoretical with experimental results. Instrumentation developed provided the sensitivity and resolution needed to measure rock deformation around a full-scale raise bore during excavation. Results of the tests conducted at the Lucky Friday mine, Mullan, Idaho, show the relationships between (a) de- formation vs. time, and (b) deformation vs. bit progress. Based on theoretical evaluation of the initial deformation, the medium appeared to behave elastically. Using an estimated field stress of 5,500 psi and Poisson&apos;s ratio of 0.20, the gross modulus of elasticity of the rock was calculated to range from 3.15 to 6.0 x 106 psi (with one outlier which was determined to be >12 x l06 psi).

Jan 1, 1971

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed&apos; constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty&apos;s, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

Albin, B. R. Billings, Mont. 28 Amster, Nathan L 25 Broad St., New York, N. Y. &apos;28 Bache, Jules S. 42 Broadway, New York, N. Y. 28 Barrett, C. P. 5338 Harper Ave., Chicago, 111. &apos;28 Baum, Frank G., Cons. Hydro-Electric Engr Cassel, Shasta Co., Cal. &apos;28 Bayless, William S. Russ Bldg., San Francisco, Cal. &apos;28 Bean, Louis H.60 E. 42nd St., New York, N. Y. &apos;28 Beatty, Roes J. 1105 First National Bank Bldg., Chicago, Ill. &apos;28 Benwell, Oswald F. Hold Mags. &apos;28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. &apos;28 Blumenthal, Hugo 44 Pine St., New York, N. Y. &apos;28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. &apos;28 Bowlus, Thomas H. Iola, Kan. &apos;28 Brown, Colvin B. Chamber of Commerce, Washington, D. C. &apos;28 Bart, Maxwell Struthers Southern Pines, N. C. &apos;28

Jan 1, 1932

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li2O and 0.45 pct Fe2O3, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing. SINCE the close of World War II there have been numerous developments resulting in the increased use of lithium by industry. Notable among these has been the development of an industrial lubricant, based on lithium stearate, which is fluid at low temperatures, stable at high temperature, and insoluble in water. A new bleaching agent, lithium hypo-chlorite, has also been developed recently.&apos; Other well-known uses are listed below: 1—Lithium oxide in ceramics reduces firing time, lowers melting temperatures, lowers thermal expansion, raises refractive index, and improves chemical resistivity. 2—Lithium carbonate and lithium strontium nitrate are used in pyrotechnics for their brilliant red color.&apos; 3—Lithium chlorides and fluorides are used as fluxes for welding aluminum and magnesium.&apos; 4—The affinity of lithium for nitrogen is the basis for a process used in purifying helium." 5— Lithium chlorides and bromides are used in air conditioning for their powers to absorb organic amines, ammonia, and smoke.6-—Lithium hydride has been used as a source of hydrogen to inflate life rafts and balloons used by the Air Forces and Navy.&apos; 7— Lithium metal and lithium hydride are useful in the atomic energy program in connection with the production of the isotopes of hydrogen." During the 1942-45 period of World War 11, Solvay Process Co. operated a flotation plant with a daily capacity of 300 tons of ore for the production of spodumene concentrate near Kings Mountain, North Carolina. The operation was shut down upon reduction of wartime demand for lithium chemicals, and until recently there has been no production from the Carolinas. In April 1950 an investigation of the problem of spodumene flotation from North Carolina ores was begun at North Carolina State College Minerals Research Laboratory at Asheville, N. C. This laboratory, operating under the combined auspices of North Carolina State College, North Carolina Department of Conservation and Development, and the Tennessee Valley Authority, undertook the spodumene project at the request of Foote Mineral Co. of Philadelphia. The work, involving a period of 15 months of intensive batch and pilot plant investigation, was completed in June 1951 and resulted in development of a process for concentration of spodumene by flotation which has been hereto unrecorded in the literature. A similar approach has been used before on iron, ilmenite, and other minerals, but the literature shows no record of its having been applied to spodumene. Parts of the process are now being used on a commercial scale at the Foote Mineral Co. plant near Kings Mountain, N. C., which has been in production since July 1951. It is the purpose of this paper to describe some of the results of the investigation. The Orebodies Spodumene-bearing pegmatites occur in a narrow belt 24.5 miles long and 1.8 miles wide extending southwestward from Lincolnton to Grover, N. C. According to statements judged to be conservative, the tin-spodumene belt of the Carolinas contains an estimated 4,300,000 tons of pegmatite ore averaging 15 pct spodumene. This amounts to "a reserve of at least 650,000 tons of spodumene (more than 20,000 tons of metallic lithium) to a depth of 100 ft."&apos; This figure includes only bodies having an average thickness of 35 ft and length of 550 ft. There are hundreds of pegmatites in the belt, many of which are less than 10 ft wide. The largest pegmatite in the area has a maximum thickness of 395 ft and maximum length of 3250 ft.&apos; These larger pegmatites are composed principally

Jan 1, 1954

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320&apos; C. Because of the size of our induction coil we are limited to this temperature, although it &apos;would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700&apos; to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937

By J. A. Hafford, J. K. Kerver, J. G. Richardson, P. M. Blair, J. S. Osoba

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By J. K. Kerver, J. S. Osoba, J. G. Richardson, P. M. Blair, J. A. Hafford

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By E. J. Rapperport, E. D. Levine

The boundaries of the (a +ß) field in the Al-Li system were determined between 150°and 550°C utilizing quantitative metallography and lattice-parameter measurements. The solubility of lithium in aluminum decreases from 12.0at. pct Li at 550°C to 5.5 at. pct Li at 150°C. P Al-Li is saturated with aluminum at 45.8 at. pct Li and has this boundary value constant over the temperature range 150°to 550°C. THE solid solubility of lithium in aluminum has been determined by several investigators, 1-6 but, as shown in Fig. 1, there is little agreement among the various determinations. The earliest investiga-tions&apos;-&apos; are suspect because of the use of impure materials. Although high-purity materials were employed in more recent work,4&apos;5 the experimental techniques may have led to contamination of the specimens. Probably the best work has been that of Costas and Marshall,6 who obtained close agreement between results obtained by two independent phase-boundary techniques: electrical resistivity and mi-crohardness. No detailed studies of the solubility of aluminum in the bcc ß phase, Al-Li, have been reported. Cursory investigations1,2,6 have indicated only that the (a+ß) -p boundary lies between 40 and 50 at. pct Li and is relatively independent of temperature. The present work was undertaken in order to provide an independent check on Costas and Marshall&apos;s determination of the solubility of lithium in aluminum, to extend knowledge of this solubility limit to temperatures below 225°C, and to make an accurate determination of the solubility of aluminum in Al-Li. EXPEFUMENTAL Alloy Preparation. In view of the difficulties encountered in previous investigations of the A1-Li system, close attention was paid to the use of methods of alloy preparation and treatment that would minimize contamination. Aluminum sheet (99.99 + pct Al) was vacuum-induction melted in a beryllia crucible to remove hydrogen. Lithium (99.9 pct Li) was charged with pre-melted aluminum into a beryllia crucible, in a helium-filled drybox. The crucible was sealed in a Vycor tube and transferred from the drybox to an induction furnace. Melting of alloys was performed by induction heating in a helium atmosphere. Solidification was accomplished by means of a suction apparatus, shown in Fig. 2, in which the alloy was forced by changes of pressure into a 3/16-in. inside diam closed-end beryllia tube. This technique produced rapid solidification of a small portion of the melt, resulting in alloys with a high degree of homogeneity. Typical lithium distributions are presented in Table I. Transverse sections 1/8 in. long were cut from the alloy rods, and each section was split in half longitudinally. One half of each section was analyzed for lithium, and the opposing halves were employed for phase-boundary determinations. Lithium contents were determined by flame photometry with an accuracy of 1 pct of the amount of lithium present. Thermal Treatments. Homogenization and equilibration heat treatments were performed in electrical-resistance furnaces with temperatures controlled to ± 2OC. Calibrated chromel-alumel thermocouples were employed to measure temperature. Homogenization was performed in helium-filled l?yrex tubes for 1 hr at 565°C. The encapsulated specimens were then transferred directly to furnaces maintained at lower temperatures for equilibration. Equilibration times were 2 hr at 550°C, 8 hr at 450°C, 27 hr at 350°c, 90 hr at 250°c, and 285 hr at 150"~. These times were chosen on the basis of conditions employed by previous investigators. Alloys were quenched from the equilibration temperatures by breaking the capsules into a silicone oil bath. By performing all possible operations either in sealed capsules or in a helium-filled drybox, the specimens were given minimum exposure to the atmosphere. Quantitative Metallography. Metallography of Al-Li alloys is difficult because of the atmospheric reactivity of the ß phase. It was found possible, however, to prepare surfaces of good metallographic quality by preventing contact with moisture during preparation. Grinding through 4/0 paper was performed in the drybox. The specimens were then transferred under kerosene to the polishing wheel. Three polishing stages were employed: 25-p alundum with kerosene lubricant on billiard cloth, 1-µ diamond paste on Microcloth, and 1/4-p diamond paste on Microcloth. Between stages the samples were cleaned by rinsing in trichloroethylene and buffing

Jan 1, 1963

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee&apos; studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.&apos; Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By L. D. Tracy

On Aug. 5 and 6,1918, and Mar. 26, 1919, the writer made an investigation of the mine-water neutralizing plant at the Calumet mine of the H. C. Frick Coke Co. The object of this plant is to develop a process of treating the water pumped from the mines so that it may be rendered suitable for use at the power plants of the mines and also at the coke ovens; at the same time, eventually producing a byproduct which will have enough commercial value to provide a sufficient revenue to place the plant on a self-sustaining basis. The Calumet mine is situated in Mt. Pleasant Township, Westmoreland County, Pa., on a branch of the southwest branch of the Pittsburgh Division of the Pennsylvania Railroad. It is about 6 mi. (9 km.) southeast of Greensburg, the county seat of Westmoreland County. The coal, which is the Pittsburg or Connellsville seam, lies at a depth of about 200 ft. (60 m.) and is brought to the surface by means of a shaft. The output of the mine averages 200,000 tons of coal annually, all of which is made into coke, either at the ovens, at the mine, or at byproduct ovens. There are 260 coke ovens at the mine. The continued development of the coal fields of Pennsylvania and the increased use of electric power in the operation of the mines has brought the problem of an increased water supply for the plants to the attention of the coal operators. This is especially true in the Connellsville coking region, where large quantities of water are used in quenching the coke at the ovens. Many of the streams receive the drainage from the mines; and as this water is highly acid and contains sulfur in various forms, some method of treatment is necessary to render it suitable for use at the plants of the mines. With this end in view, the H. C. Prick Coke Co., about 4 years ago, installed at its Calumet mine a plant for experimental purposes, in an endeavor to develop a process that would provide a maximum amount of suitable water at a minimum cost. From a purely technical point of view, the result of these experiments has been encouraging. The company is now endeavoring to place the plant on a commercial basis.

Jan 1, 1922

By H. Warlimont

Precipitation of cementite plates from carbon-rich austenite gives rise to localized formation of martensite in the matrix next to the precipitate upon quenching. The growth of this martensite is urmsually restricted. A distinct lattice relationship is found between this martensite and the cementite phase. It is concluded that the martensite is nacleated in the region of lowest carbon concentration at the austenite-cementite integace, with low-energy matching to the cementite lattice. The restriction of the growth of the martensite phase to the vicinity of the cementite plates can be explained by misfit in the austenite -martensite glissile interface and the uphill carbon gradient in the austenite. The investigation was carried out by light- and electron-microscopy and by electron-diffraction of thin foils. THE precipitation of cementite from carbon-rich austenite gives rise to a localized formation of martensite in the matrix next to the precipitate upon quenching. This behavior has been described previously by A. B. Greninger and A. R. Troiano1 for a 1.78 pct C steel ("pseudomorphic martensite"), and by A. Hultgren2 for a Fe-0.99 pct C—5.20 pct Mn steel. By measuring the axial ratio of the martensite phase,&apos; it was found that the carbon content of this martensite was lower than that of the martensite which formed without prior partial transformation to cementite. Therefore, it was concluded that lowering of the carbon concentration in the matrix next to the precipitate raised the M, temperature locally and thus led to nucleation of martensite at the ce-mentite-austenite interface. However, the restriction of the growth of the martensite phase to the vicinity of the cementite plates cannot be explained by localized carbon impoverishment alone. Under ordinary conditions a martensite plate which has been nucleated in a favorable site can continue to grow until it encounters a physical barrier, or until it encounters a compositional barrier in the matrix, where the total free-energy change for the reaction is not negative, since it has been shown by numerous experiments that the activation energy for growth of ordinary martensite is virtually zero.&apos; An investigation was conducted by transmission electron microscopy and electron diffraction to study this extraordinary martensite. It was expected that crystallographic in addition to compo- sitional conditions caused this abnormal mode of martensite formation. MATERIAL AND PROCEDURE An Fe-C-Mn alloy containing 1.15 pct C and 5.1 pct Mn was used for most of the experiments. For metallographic work, specimens 15 by 15 by 3 mm were used. For preparation of thin films, the initial specimen size was 15 by 15 by 0.7 mm. The heat treatment of each specimen consisted of austenitizing for 1/2hr at 1100&apos;~ in an argon atmosphere, subsequent isothermal holding in a lead bath at one of a series of different temperatures, and, finally, quenching into brine at room temperature. For metallographic examination, the specimens were mounted in bakelite (slight tempering effects resulted from the heat in the mounting press) ground, polished, and etched in nital. Thin films for transmission electron microscopy and electron diffraction were obtained by grinding the specimens to approximately 0.2 mm thickness and subsequent electrolytical thinning. The orientation relationships were evaluated from sets of electron micrographs and selected-area electron diffraction patterns of single units of the transformation products and the adjacent matrix. RESULTS In the alloy which was used for the experiments, proeutectoid carbide precipitates over a wide tem-

Jan 1, 1962

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943