Search Documents

By K. H. G. Ashbee, J. W. Heavens

One consequence of the distribution in orientation of Bragg diffracting planes in an elastically bent foil is that simultaneous diffraction occurs from ±g pairs, where g is the reciprocal lattice vector to a diffracting plane. If such Bragg contour pairs are indexed, then the variation in orientation with respect to the incident electron beam is known. This note describes a construction by means of which Bragg contour pairs may be indexed by inspection. Referring to Fig. 1, the Ewald sphere radius is l/h, where is the wavelength of the electron beam, and the half spacing of first-order reciprocal lattice planes is l/d, where d is the corresponding spacing in direct space. The angle subtended by the zero and first-order planes at the center of the Ewald sphere is a = sin-' Thus, to represent a pair of first-order Bragg contours on a stereographic projection, measure ±a from, and along the normal to, the zero-order plane. The traces of the required Bragg contours pass through these points and parallel to the zero-order trace. In practice, it is desirable to enlarge a stereographic projection of the zero-order planes before making the construction. As an example, a stereographic projection of first-order Bragg contours up to line 27 for an fcc crystal is given in Fig. 2; if required, higher-order contours can easily be added. Fig. 2 is, of course, a map of first-order Brillouin zone boundaries. One use of this construction is the measurement of large elastic fields in electron microscope specimens. Fig. 3(a) shows a pattern of Bragg contour pairs due to lattice distortions near a large precipitate. This particular example is of a T-phase precipitate in Hidu-minium 54 (A1 + 6 wt pct Cu, 0.5 wt pct Mn). Foil buckling is produced by annealing during observation and may be evidence for evaporation from the precipitate.' Comparing Figs. 2 and 3(0), it is evident that the axis of high symmetry in Fig. 3(a) is [lll]. The strain in a bent foil is approxinlately t/2r, where / is the foil thickness and ? the radius to which the foil is bent. From the projections of grain boundaries and of helical dislocations, it was estimated that ( - 3000A, and values for ? were obtained from the

Jan 1, 1968

By C. O. Worden, C. A. Zapffe, F. K. Landgraf

SUMMARY FOLLOWING the discovery of Parke and Ham that deoxidation control of cast molybdenum can be predicated upon simple fractographic examination, a special study of that metal was undertaken to investigate those patterns ascribed to forgeability and nonforgeability. An elaborately developed system of cleavage patterns immediately rewarded the study; and they are reported here as a necessarily preliminary contribution calling attention to information which is both new in type and in origin. In general, the present observations confirm those of Parke and Ham, and Woodside; but they also disclose a wealth of detail and correlated phenomena which greatly expand the earlier information. For example, the oxide pattern of nonforgeability is found to be complex, perhaps involving as many as three distinctive patterns. And the nature of the carbide seems to be at least twofold. In addition, transgranular facets are here shown for the first time. Elaborately complex, but in a characteristic manner, these facets depict distortion in original crystal growth which provides truly extraordinary patterns. No carbide and oxide forms display themselves transgranularly, except in profile as exceedingly thin superficial films at the grain boundaries. Crystallographic features are also rare-a condition undoubtedly resulting from the great substructural distortion; but occasionally registrations are found of cleavage on {001}, and faulted areas believed to be Neumann-type deformation on {112}. INTRODUCTION Parke and Ham, 1 and again Woodside, 2 have reported that the forgeability of molybdenum cast by their vacuum-electric-arc process can be predicted with great dependability by a simple fractographic observation. They state that nonforgeability is the result of a grain boundary oxide which can be readily identified on the fracture facet at high magnification; and they convert the nonforgeable condition to a forgeable one by increasing the carbon content of the melt until the oxide structures subsequently observed in the fractograph become replaced by a second strongly marked pattern characteristic of carbide and coincidentally indicative of forgeability. Considerable importance immediately attaches to such observations: (I) because of their direct commercial application to one of metallurgy's inviting and relatively unexplored metals; (2) because of a general scientific curiosity regarding the nature of these characteristic markings; and (3) perhaps more important, because of

Jan 1, 1948

By Philip B. Bucky

THE Mining Methods sessions, one of which was run jointly with the Industrial Minerals Division, were fortunate in having a number of exceptionally fine papers. At the Tuesday session R. P. Smith presented the results of six years' experience with prepaid medical care for the employees of the Hollinger mine. It was felt that this paper was a real contribution to the cross field of mining-medicine, and the presentation was exceptionally well done. Olof V. Lindqvist acquainted us with the consider- able progress made in blast-hole diamond drilling in recent times, especially in Canada. The opening of a mine is always a matter of considerable interest and the description of the procedure and problems encountered in opening the Mather mine of Cleveland Cliffs Iron was presented by L. C. Moore.

Jan 1, 1944

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By E. F. Bradley, R. I. Jaffee, H. R. Ogden, E. S. Bartlett, D. N. Williams

The mechanical properties of solid-solution-strengthened columbium alloys have been assessed as a function of alloying additions. Studies included the effects of tungsten, tantalum, molybdenum, and vanadium. Elevated temperature fabrication was required at alloying levels above about 15 pct W or 10 pct Mo. Tungsten, molybdenum, and vanadium additions increase tensile strength at room temperature and 2200°F, but tantalum additions exert little strengthening. Similarly, tungsten, molybdenum, and probably vanadium additions increase the ductile-to-brittle transition temperature, and tantalum additions decrease this parameter. The 2200°F stress-rupture strength is increased by tungsten and molybdenum additions; with 20 to 25 at. pct additions, 100-hr rupture strengths of 30,000 psi are obtainable. Small vanadium additions exhibit mild stress-rupture strengthening, and tantalum additions are innocuous. At 2500°F, tungsten additions retain stress-rutpure strengthening capability, but molybdenum additions are much less effective. Tantalum additions augment the stress-rupture strengthening of tungsten plus molybdenum additions at 2500°F. Of the refractory metals, columbium possesses specific potential for structural use in the temperature range from 2000" to about 2500°F. Desirable features of columbium are its good low-temperature ductility, ease of fabrication, oxidation mechanics (lack of a volatile oxide at moderate temperatures), good availability and reserves, and relatively low density. However, alloying is required to provide attractive strength at elevated temperatures. Published information concerning alloying be- havior of columbium relative to mechanical properties is sketchy, particularly in consideration for long-time applications at temperatures in excess of 2000°F. Only a few stress-rupture data at temperatures from 2000" to 2500°F have been reported;'-' these are too meager to allow rationalization of the effects of various alloying additions on creep or stress-rupture properties. Additional published data do, however, give some insight toward understanding of systematic alloying behavior for columbium relative to low-temperature strength4-' and ductility,' and elevated temperature tensile behavior.4,6 This paper is intended to augment previous knowledge, and to promote understanding of the alloying behavior of columbium for long-time structural service at elevated temperature. BASIC CONSIDERATIONS Solid-solution strengthening is recognized to be of prime importance in improving strength in columbium-base alloys. Other strengthening mechanisms may be (and are, in current alloys) used to augment solid-solution strengthening. As strengthening results primarily from lattice distortion, the strengthening effectiveness per atom depends upon atomic size mismatch between solvent and solute. Another factor in this regard is conformance to ideal solution behavior in the solid solution. Thus, for example, despite appreciable differences in the degree of mismatch between tungsten (5 pct), molybdenum (5 1/2 pct), and vanadium (7 1/2 pct) in solution in columbium, all are about equally effective in straining the columbium lattice at room temperature.'-' Similarly, tantalum additions do not strain the columbium lattice, and little strengthening is expected. Size effects being equal, maximum solution strengthening at high temperatures is anticipated to result from the addition of elements that increase the melting temperature of columbium. This expectation is based on an increase in the electronic bonding forces exhibited in the transition metal series as electronic structures approach those of the Group Vl metals. Of the metals that exhibit ex-

Jan 1, 1963

By J. M. GLEDHILL

(Washington Meeting, May, 1905.) A Discussion of Mr. J. M. Gledhill's paper, read by title at the Lake Superior meeting, but presented first at the New Yolk meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement. Between the two Institutes. Discussion. MR. E: WINDSOR RICHARDS, Past-President, said that at a recent meeting of the Institution of Mechanical Engineers a paper was read on tool steel, and he called the attention of the members to the high-speed tool steel at the Bethlehem Works. They would have the pleasure of seeing those wonderful works and would see 60, 70, 80 and 100 tons oil lathe with half-a-dozen of these high-speed tools running. PROP. H. M. HOWE (Columbia University) said that they all looked upon these high-speed tool steels as of very great importance, particularly to the machine shop. One point occurred to hire : Had it really been shown that Swedish steel is necessary, or better than equally pure steel that is not Swedish; and is cemented steel really necessary, and is there any advantage in using that, rather than equally pure open-hearth steel'! It might be well if the author could indicate the kind of evidence on which lie bases his assertion that it is necessary to have cemented Swedish steel. Many were hoping for the development of high-speed steels from elements which exist in great quantities, such as silicon, manganese and chromium, rather than from rarer metals like molybdenum, vanadium and tungsten, the supply of which is likely to be soon exhausted. If the high-cutting speed was to last more than a generation, it. seemed to him that they would have to draw upon the common ele¬ments and not upon the rare ones. MR. Tom WESTGARTH (Middlesbrough) said he fully appreci¬ated what had been said about the advantages of using high-speed steel, because great benefit had been derived from the

Mar 1, 1905

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum were grown by multipass zone melting in an electron beam apparatus. Tension tests of these crystals at 4.2 x 10&apos;* per sec-gave a resolved louler yield stress of 7300 psi at with a chisel edge; total uniform deformation increased from 1 to 2 pct at 77°K to over 20 pct at 300°K. This, and slip traces, indicated that deformation is more inhomogeneous at lower temperatures. Deformation occurred exclusively by slip in <III> directions, on planes in the <111> zones. Cross slip was frequent, particularly for those orientations where the resolved shear stress on the cross system was comparable with that on the primary plane. The existence and magnitude of the upper yield point were found to be sensitive to orientation. This effect was related to the circumvention of dislocations which were "locked" by interstitial atoms, by double cross slip, or composite slip, of screw dislocations. Prestrainirg at 300°K did not remove the upper yield point in subsequent tension at 77°K. Also, this treatment was found to cause yield points, where none existed for the unprestrained material. This behavior was also rationalized in terms of the circumvention mechanism. The mechanical properties of polycrystalline tantalum have been investigated by several workers,1"4 and may be summarized by pointing out the following features: a) Sharp rise of yield stress with decreasing temperature below room temperature. b) Response to strain aging at 300" to 400"C. c) Yielding with upper and lower yield-point phenomenon at and below room temperature. d) Low strain hardening below room temperature. e) Reluctance to twin except at very high strain rate. Furthermore, tantalum is ductile at ordinary strain rates as low as 4.2"K.&apos; This feature, in particular, makes tantalum unique among the high melting point, bee transition metals of Groups V and VI in the periodic system. Therefore, a more fundamental and detailed knowledge of the low-tempera- ture deformation of tantalum is required. Since high purity and the absence of grain boundary effects make such a study most productive and unambiguous, the method of electron beam zone melting was selected for the preparation of test specimens. This technique has the further advantage that crystals may be seeded in order to obtain any desired orientation. EXPERIMENTAL The electron beam zone-melting equipment was constructed as a modification of that described by Calverley, Davis, and Lever? All crystals were made by three passes of the molten zone at 4 mm per min to achieve an optimum purity commensurate with economy of time and material. Table I reports the chemical analyses of the starting and refined metal. It will be noted that there remain some 50 to 70 wt ppm of interstitial elements, while all substi-tutional elements have been removed by evaporation. Tungsten is picked up by evaporation of the cathode filament wire. Crystal seeding was normally successful within 3 deg, and the orientation of all crystals are given in the standard stereographic triangle in Fig. 1. Tensile bars were prepared from the crystals by centerless grinding to the shape in Fig. 2. Specimens were then electropolished to remove 10 pct of the diameter in order to remove worked material and to prepare a metallographic surface for subsequent deformation trace observations. All specimens were held in the split bushing grips as indicated in the cross section view of Fig. 2. All tests were made at a strain rate of 2 112 pct per min in an Instron testing machine.

Jan 1, 1962

[Alphabetic Section: The letter immediately following a member&apos;s name indicates grade: M-member, A-associate, J-junior. The numerals following member&apos;s grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member&apos;s name indicates availability for consulting work:]

Jan 1, 1961

By Paul M. Tyler, Herbert R. Mosley

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority&apos;s research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee&apos;s phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By Herbert R. Mosley, Paul M. Tyler

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority&apos;s research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee&apos;s phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982

By James Kemp

IN earlier years, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections-and maps prepared forty or more years ago for the Second Geological Survey of Pennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.1 So far as I can discover faults fail in the charts, except in one small case in the Henry Colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barre, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a number of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer&apos;s surveys, possess great scientific and practical interest, bearing as .they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an, effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to, Mr. Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due.

Jan 1, 1922

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,&apos; the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By H. Reginald Hardy, Gary L. Mowrey

Field studies were conducted over a longwall coal mining operation to investigate the feasibility of using microseismic techniques to detect and to locate any areas of instability in the vicinity of the longwall. An array of geophones buried at depths of 3 to 8 m from surface were positioned approximately 130 m above the active area of the longwall panel. A mobile microseismic monitoring facility amplified, filtered, and recorded the microseismic activity sensed by the geophones. Microseismic events were detected at depths of at least 130 m and at horizontal distances in excess of 250 m from the source. Most events, which resembled decaying sinusoidal transients, had frequencies of 10 to 100 Hz, and particle velocities of 1 to 8 pm/s. Source locations for the 150 largest events were computed using a least-square travel-time-difference method. Both isotropic and unique wave propagation velocity models were considered when evaluating the source locations. Most of the events were computed to be within ± 30 m vertically of the coal seam and ± 15 m horizontally of the longwall face, when the unique velocity model was employed.

Jan 1, 1980

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By Earl W. Palmer, Cyril Stanley Smith

A study of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors&apos; conclusions regarding graphitization. Material Used After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in, in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made on the castings after commercial mallealleizing and after special heat treatments to be described. The analyses of the white irons are given in Table 1.

Jan 1, 1935

By Cyril Stanley Smith, Earl W. Palmer

A study of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors&apos; conclusions regarding graphitization. Material Used After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in, in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made on the castings after commercial mallealleizing and after special heat treatments to be described. The analyses of the white irons are given in Table 1.

Jan 1, 1935

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg&apos; using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962