Search Documents

The First Conference of the Powder Metallurgy Committee convened in the East Foyer of the Hotel Waldorf-Astoria, New York City, at 9:45 a.m., on Feb. 21, 1944, Mr. John Wulff, General Chairman, presiding. THE CHAIRMAN.-In behalf of the American Institute of Mining and Metallurgical Engineers I welcome all members and guests to this conference on Powder Metallurgy. We hope that this meeting will give expert and novice in the field a chance for discussion. Unfortunately, the subject has been overemphasized by some, and, of late, severely criticized by others. We have here today powder producers, fabricators, and engineers of different viewpoints, who can make the meeting a success. Such success depends not only on the caliber of the papers presented but more so on the discussion. To give you time for a free exchange of views, the papers have been shortened purposely. With the hope that you will all benefit by this conference, I shall turn the meeting over to the Chairmen of the morning session, Mr. Roland P. Koehring, of Moraine Products Division of General Motors, and Dr. R. K. Waring, of the New Jersey Zinc Company. SESSION ON DESIGN FACTORS IN POWDER METALLURGY R. P. Koehring and R. K. Waring presiding The opening paper of the session was presented by Mr. Fred P. Peters, as follows:

Jan 1, 1945

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

[ASSETS CAPITAL ASSETS: Equity in United Engineering Society's Land and Buildings $486,792.79 Library 40,000.00 $526,792.79 INVESTMENTS: Jas. Douglas Fund-Schedule #2 $ 99,966.40 Life Membership Fund-Schedule #3 9,415.63 R. W. Hunt Medal Fund-Schedule #4 7,489.09 116,871.12 INVENTORIES: Paper Account 305.10] [ ]

Jan 1, 1925

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3

Jan 1, 1923

By David L. Holt

It is well-established that hydrostatic pressure distribution is hardly achieved during uniaxial compaction of powders. All the previous investigations1-4 give consistent results and this variation is attributed to the die-wall friction. The conclusions are based on measurements of the density of very small portions of the compact. Although the analysis of the density or the strain distribution in the compact is very helpful in obtaining information about the stress distribution within a powder compact, it does not describe the problem from a more fundamental point of view. The densification in metal powder compacts takes place chiefly by plastic deformation (ignoring particle rearrangement) at the points of contact of the powder particles. The onset of yielding and subsequent growth of the contact areas (for spherical powders) take place fixed by a constant stress equal to three times the yield stress in tension or compression,5-7 assuming little or no work hardening. Therefore, by deforming spherical powders in the die and measuring the contact areas on each particle, the load at each contact point can be determined. In the present investigation, this was done by hot-pressing uniform spheres of lead, K-Monel, and sapphire. The details of the experiment have been described elsewhere.' The spheres were studied for the size and the number of contact points on each particle using a specially designed goniometer. It was found that the deformed faces that were approximately normal to the direction of pressing were about 2.2 times larger than those parallel to the direction of pressing. Fig. 1 shows the typical deformed sphere. A detailed study showed that the mean value of the contact areas on each sphere was within 5 pct for all the spheres in the die (ignoring those touching the die walls and the top and bottom of the die).' The spheres touching the die walls and the top and bottom of the die were found to have larger contact areas (8 to 10 pct) which indicates higher pressures in these regions of the compact and thus higher compact densities in these regions. These results show that density distribution calculated from such an experiment will give results consistent with the previous investigators. It is concluded, therefore, that the pressure distribution in the die is better understood by studying contact areas on each particle. 'R. Kamm, M. A. Steinberg, and J. Wulff: Trans. TMS-AIME, 1947, vol. 171, p. 439. 'Pol Duwez and Leo Zwell: I. Metals, 1949, vol. 1, p. 137. 'G. C. Kucynski and I. Zaplatynskyj: Trans. TMS-AIIME, 1956, vol. 206, p. 215. 'R. P. Seelig and J. Wulff: Trans. TMS-AIME, 1946, vol. 166, p. 492. 'H. Hencky: Z. Angew. Math. Mech., 1923, vol. 3, p. 241. "J. Ishlinsky: I. Appl. Math. Mech. USSR, 1944, vol. 8, p. 233. 'D. Tabor: Proc. Roy. Soc. (London), Ser. A, 1948, vol. 192, p. 247. 'Ashok K. Kakar and A. C. D. Chaklader: 1. Appl. Phys., 1967, vol. 38, p. 3223. Superplasticity in 60Zn-40Al David L. Holt THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

ASSETS CAPITAL ASSETS Equity in United Engineering Society's Land and Buildings $486,792 79 Library 40,000 00 $526,792 79 INVESTMENTS Jas Douglas Fund-Schedule #2 $ 99,966 40 Life Membership Fund-Schedule #3 9,415 63 R W Hunt Medal Fund-Schedule #4 7,489 09 116,871 12 INVENTORIES Paper Account .305 10

Jan 1, 1923

[A AALSETH Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Mont ABADIE Henry G (M 43) Asst to. Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif. ABBET Waldo (A 56) Asst Diet Oper Supt Sun Oil Co P 0 Box 66, Stowelt, Tex ABBOTT Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT Fred E Jr (M 59) Abqaiq Diet Mgr Arabian American Oil Co Dhahran, Saudi Arabia ABBOTT J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT Richard H (J 51) Partner Abbott & Howard 422 W Hermosa, San Antonio 12, Tex ABBOTT William G (M 50) Div Mgr Rice Engrg &. Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carml, 111]

Jan 1, 1961

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

1. How Does One Determine Whether an Ore Body Will Block-cave? Page Mark A. Smith......... 122 Harry A. Leidich........ 122 McHenry Mosier ...,.. 22 R. W. Hughes ........ 122 Sherman R. Burdick ....... 123 R. T. Gallagher........I 23 Benjamin F. Tillson...... 123 Lucien Eaton...........123 C. F. Jackson..... . .. 123 Philip B. Bucky........... 126 2. How Does One Determine the Block Dimensions and the Development Work Necessary to Make an Ore Body Cave? Mark A. Smith... 125, 127, 129 Harry A. Leidich..........126 McHenry Mosier......126, 127, 132 R. W. Hughes...........126 Sherman R. Burdick.........127 R. T. Gallagher...........127 Benjamin F. Tillson......127,131 L. E. Young............127 Robert D. Hoffman.......128, 132 Gerald Sherman..........128 Philip B. Bucky......130, 131, 132 K. S. McClellan..........132 Tell Ertl.............132 3. How Do the Forces Act and What Are the Stresses Developed in a Block That Cause It to Block-cave? Mark A. Smith.........132, 135 Harry A. Leidich........133 McHenry Mosier . .. 133 R. W. Hughes ....... 133 Sherman R. Burdick..... . 133 R. T. Gallagher..........134 C. F. . Price, Jr. ........134 Benjamin F. Tillson.........134 C. F. Jackson......134, 135,137 R. Taborelli...........135 Frank A. Ayer ... .....136 Philip B. Bucky . .........136 Rollin Farmin . . .......136 . . . Weysser.....135, 136, 137 George S. Rice...........137 4. What Determines the Procedure in Removing Caved Ore? Harry A Leidich...........137 McHenry Mosier........137,141 R. W. Hughes...........137 Sherman R. Burdick........138 R. T. Gallagher...........138 Mark . Smith...........138 Philip B. Bucky......140,141,143 C. F. B. Price, Jr..........140 R. H. Bennett...........141 C. F. Jackson..........141, 143 Gerald Sherman..........141 Tell Ertl.............141 .. .. ..................143 C. H. Shoemaker..........143 5. What Are the Criteria for Determining the Efficiency of a Block-caving Operation? Harry A. Leidich.......... 143 McHenry Mosier......... 144 R. W. Hughes........... 144 Sherman R. Burdick.......144 R. T. Gallagher . ......... 144

Jan 1, 1946

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICKARD, Vice-Chairman D. MI. LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BOHN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON, Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology. Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 8, 1917

CONTENTS DAVIS, CARL R., WILLEY, J. L., and EWING, S. E. T.-Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores. Discussed by Charles E. Locke, H. W. Hardinge, H. N. Spicer, G. M. Brown, Justice F. Grugan, R. C. Canby 1 WEINIG, A. J., and BOWEN, MAX W.-Determination of Dissolved Oxygen in Cyanide Solutions. Discussed by A. L. Blomfield, M. F. Dycus, A. W. Bull.... 4 LEPSOE, ROBERT.-Precipitation Efficiency of Zinc Dust in Cyanide Process. Discussed by G. M. Brown, Charles E. Locke 5 Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores Discussion of the paper of CARL R. DAVIS, J. L. WILLEY, S. E. T. EWING, presented at the New York Meeting, February, 1925, and issued as Paper No. 1386-B, with MINING AND METALLURGY, December, 1924. CHARLES E. LOCKE, Cambridge, Mass.-In this country, we have come to think that we should use smaller size of feed in our ball-mills. I will admit that a ball-mill is not comparable to a tube-mill, as conditions may not be the same, but there we have an unusual demonstration of the advantage of a coarser feed. Further investigation along this line is going to lead to some valuable results. The authors have overcome the difficulty of this coarse feed by taking out what I would call the difficult lumps, It is not clear from the paper whether many of these difficult lumps' may not be 'reduced portions of their grinding media. H. W. HARDINGE, New York, N. Y.-The idea is not exactly new because in 1911 they used the miner to reduce the finer material. We proceeded three or four years using many tons, about 15 tons. or nearly the same proportion of ore to grinding medium. Another thing to be taken into account is the hardness of the ore being ground. In South Africa, the transportation costs must be, taken into account. They are also making progress in the method of using tube-mills and ball-mills instead of stamps. Experiments are to be conducted with 10-ft. diameter mills there, with the object of increasing the mass action and agitation which, as has been demonstrated under different circumstances, increases the overall efficiency.

Jan 6, 1925

By Charles Berkey

CONTENTS PAGE C. P. Berkey-Responsibilites of the Geologist in Engineering Projects (with discussion) 4 Kirk Bryan-Problems Involved in the Geologic Examination of Sites for Dams 10 0. E. Meinzer-Relation of Ground-water Conditions to Leakage of Reservoirs (with discussion) 19 Charles Terzaghi-Effect of Miner Geologic Details on the Safety of Dams (with discussion) 31 G. H. Matthes-More and Better Geologic Data for Use in Hydraulic Projects (with discussion) 47 L. W. Fisher and R. D. Ohrenschall-Geologic Examination of Dam Sites in the Tennessee and Cumberland River Basins 60 C. K. Wentworth-The Geology of Dam Sites (with discussion) 78 L. C. Glenn-The Geology of Dams and Reservoirs 97 H. T. Stearns-Success and Failure of Reservoirs in Basalt (abstract) 111

Jan 1, 1929

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965