Search Documents

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,'-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,'-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By Henry N. Toler

Activity in the search for oil and gas in Mississippi was greater than it had been for several years. Interest manifested and exploration work in wildcat areas were at an all-time peak. Drilling activity in the state's two proven fields continued to decline; there being only four wells drilled in the Jackson field during the year. At the end of 1937 it seems very likely that 1938 will be a big year in the search for oil in Mississippi. Deilling Activity Jackson Gas Field.—The four wells drilled in the Jackson field during 1937 resulted in three producers and one dry hole. Nine producing gas wells were abandoned during the year because of salt-water encroachment. The total production for 1937 was 14,248,000,000 cu. ft., which was a billion and a quarter increase over 1936, the highest year prior to 1937. The grand total produced from the field is 72,341,000,000 cu. ft. of gas and over 15,000 bbl. of oil. The three wells that had produced oil the past few years were also abandoned during the year because of the small quantity of oil and the large volume of salt water.

Jan 1, 1938

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners' Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917

By Lewis T. Wright

I have long been aware that ferruginous copper furnace-slags if fused in the electric arc will yield metallic iron containing copper, and in order to confirm this knowledge, and to obtain further information of the behavior of such slags in the high temperature and reducing conditions of the electric furnace, a number of samples of slag were fused in an experimental electric furnace. The results obtained, given in Table I., show that a very large amount of metallic iron was produced, and that this iron carried with it practically all the copper, gold, and silver, and more than 50 per cent. of the sulphur, of the original slag. The metallic buttons formed in the electric furnace were clean, hard, but not brittle.

Jan 1, 1911

One item of general interest in MINING ENGINEERING Trends, May 1952 gives the wrong impression of the scale of the ilmenite operations in North Carolina It also implies there are known deposits of rutile which "guarantee self-sufficiency for many years" So far as we know this is not true At present, rutile is in such short supply in the United States that the Defense Mineral Authority is encouraging prospecting for new deposits So far none have been found of any consequence and our needs have to be met largely from the deposits near Jacksonville, Fla, and rutile imported from Australia JAY P WOOD VICE-PRESIDENT HUMPHREYS GOLD CORPORATION The reference to self-sufficiency was meant to apply to the ilmenite-bearing sands, not rutile, but improper phrasing failed to make this clear However, the press release that the Glidden Co circulated stated that this deposit of ilmenite was one of the largest in North America -Editor

Jan 1, 1952

By Ralph Wilcox

The diamond drilling of certain characters of unstable rock formation, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as a caving " of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving—with resultant difficulties, such as decreased speed of sinking and increased consumption of diamonds—would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the out~ide of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole. The small percentage of core recovery rendered it necessary to

Jan 1, 1914

By F. B. Eiseman

IT is desired -to determine the effect of the extent of bank repairs on the final slag volume in acid electric steel-melting practice. It is understood that the repairs stud- TABLE I-Summary of Effect of Bank Repairs on Slag Volume [ ] ied here are necessary and the amount of sand added is that needed to maintain hearth and banks in a satisfactory condition. In this way the effect of repair materials on the amount of slag tapped would be found with a reasonable degree of accuracy. Ten heats were made for this study with careful attention to a uniform charge. The steel was the usual grade B and melting was carried out in a 3 1/2-ton top-charge Lectromelt furnace. Melting practice in all cases was the same-complete oxidation, with recarbonization by means of low-silicon pig iron.

Jan 1, 1947

By Howard L. Hartman

Probably no aspect of underground excavation is as important or as neglected as the environment. The Committee on Rapid Excavation, formed by the National Academy of Engineering to study the technological needs for "rapid" underground excavation in tunnels, shafts, and mines of the future, encountered a blank wall in attempting to evaluate environmental needs. In fact, so little quantitative information on the extent of present-day hazards is available that projection of future environmental-control demands must await more adequate assessment of current hazard levels. Further, there are not even accepted tolerance standards for many environmental conditions, such as heat, noise, and illumination. Only certain atmospheric contaminants have been satisfactorily catalogued. Any technical study, therefore, which purports to examine the state-of- the-art on underground environmental control must, in reality, settle for a cursory survey of a rather nebulous subject. ENVIRONMENTAL HAZARDS To contend adequately with hazards in the underground environment requires some knowledge of their nature and characteristics. In this regard, it is helpful first to identify our concern: when, where, and to whom or what may environmental conditions constitute "hazards"? Table 1 summarizes considerations that are important in this regard. For the purposes of this Conference (and book), primarily directed toward the excavation process itself, the hazards of consequence occur during excavation (item A) and primarily within the excavation (item B). However, some attention must be given to external hazards as well, since these may affect excavation. The object of concern (item C) is mainly human safety, although property security is also important. Hazards occur in a variety of forms. If one is to devise suitable control

Jan 1, 1970

By F.M. Walters

In order to isolate the effect of an element on some property of an alloy, the effect of the other alloying elements must be elimi-nated, either by reducing their quantity to the extent that they may be neglected or by determining the specitic effect of each. The success of Grossmannl in calculating hardenability from chemical composition by means of factors suggested such a

Jan 1, 1943

By F. M. Walters

In order to isolate the effect of an element on some property of an alloy, the effect of the other alloying elements must be elimi-nated, either by reducing their quantity to the extent that they may be neglected or by determining the specitic effect of each. The success of Grossmannl in calculating hardenability from chemical composition by means of factors suggested such a

Jan 1, 1943

By S. Forgeron, W. Shaw, E. L. Zodrow

Trend-surface equations are proposed for volumetric coal estimation in collieries of Sydney Coalfield, Nova Scotia. The statistical technique was first tried on Harbour coal in #20 Colliery investigating resulting residuals for abnormalities. The trend model is accepted as probably being correct as a result of that investigation. Indeed, higher degree polynomial trend- surfaces account for over 80% of the total map variability; these are encouraging statistical results, backed-up by geological knowledge about the coal seam, suggesting that the trend model has economic significance for an off-shore colliery developed to exploit the Harbour coal several kilometers east of #20 Colliery. Specifically, the need for additional offshore drill holes for the new colliery (excepting quality assessment holes) should be considered in light of a developed estimating model for the new colliery. The trend model also finds application in coalfields structurally more complex than Sydney Coalfield.

Jan 1, 1983

By Maurice Rey, H. Beavers

THROUGH circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper.1 DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR 'Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By Roscoe C. Clark

In a previous technical note' by Walter Rose, evidence is offered in support of the contention that "the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely." It is not the purpose of this note to present further discussion of this possibility but rather to point out that the argument presented there does not appear to be generally valid. In the cited note' reference is made to the experiments of Welge2 wherein it was shown that when water was displaced by oil from a core the pressure in the water phase was less than in the oil phase but that when this oil was then produced by water drive the pressure in the water phase was greater than in the oil phase. Rose has concluded from these observations that conditions of static equilibrium did not obtain since the fluid saturations were such that phase discontinuities seemed unlikely. The argument from which this conclusion was drawn is based on the contention that "the pressure is always greatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase." This premise appears to have been reached from a consideration of capillary phenomena in cylindrical tubes, although it may a1so hold for other types of pore geometry, hut as will be shown below it does not hold for all pore shapes and hence is not generally applicable. Since the pore structure of porous media such as reservoir rocks i- in general so complex as to defy exact description. it is undoubtedly of great value to establish a model in terms of pore shapes of known geometry, provided of course that the limitations of the model are recognized. That the limitations of the capillary. or cylindrical, tube model have not always been fully recognized will be evident from the following discussion of a pore of different shape hut one which may a. logically he considered a.; the capillary tube. The pore space to be considered is that shown in Fig. 1, which may be thought of as the "hole in a doughnut."* Consider the interface, A-B-A', between two immiscible fluids, P, and P2, which interface meets the solid alone a line, A-C.A'-C'. The interface A-B-A' is the surface of a spherical segmen† while the line of mutual contact be-

Jan 1, 1950

By F. R. Van Horn

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must be secured, but they do not agree as to how this can best be done.

Jan 4, 1917

By Clement K. Chase

The ammonia leach for copper recovery is discussed from historical and current practice standpoints. The chemistry of the system is presented together with Eh-pH and copper-ammonia solubility curves. A list of metals forming ammine complexes is presented. The advantages and disadvantages of the ammonia leach as applied to copper recovery in conjuction with modern liquid ion exchange techniques are compared.

Jan 1, 1980

By J. E. Strongman

This paper describes a system dynamics model of the international copper system. The development of the model is described regarding the questions it was designed to address, model boundary, major sectors and actors, the availability of data, the copper life cycle, and major supply and demand dynamics. A base forecast is presented describing future supply, demand, capacity, prices, trade flows, scrap flows and capital expenditures from 1976-1990 for the major producing and consuming market economy blocs.

Jan 1, 1977

By O. P. Arora, I. L. Caplan, H. von E. Doering

ThE interpretation of X-ray and electron diffraction data obtained in plastic deformation studies of hcp a titanium requires knowledge of angular relationships between crystallographic planes and directions. Rarey el 01.' have calculated both interplanar angles and angles between directions for a number of c/a ratios. This information, although useful for approximate applications, does not provide exact data for specific hcp metals. Recently, Hu2 has tabulated interplanar angles specifically for hcp titanium. The present study augments the existing data on titanium by providing the angles between plane normals and rational crystallographic directions in addition to interplanar and interdirectional angles. These angular relationships were calculated on an IBM 360 Computer using a Fortran IV program.* Cal-

Jan 1, 1969

Jan 1, 1940

Jan 1, 1940