Search Documents

By R. P. McLaughlin

EXACT information as to performance of the gas lift from the mechanical engineering standpoint is hard to obtain. Several hundred wells are now producing in California fields by means of the gas lift, and a survey of results shows that the gas lift has increased production at these wells by approximately 60 percent. Similar or even larger figures describe results in Mid-Continent fields. Such an increase in output of oil is so satisfactory, to the average oil producer, that it may not encourage investigation looking to more efficient operation. The cost of lifting oil by compressed gas varies from 3 c. to 15 c. per bbl. of oil, depending upon the efficiency of the gas lift. A difference of 10 c. or 12 c. per bbl. of oil is immediately noticed by an oil operator and the cost in production is as real to him as is the price of his product. Therefore, the efficiency of gas-lift process deserves more consideration than it has been given in some quarters. It has been found that there is a wide variation between different operators and at different wells in the amount of gas used per barrel of oil lifted. Some of the most efficient operations show oil being lifted with only slightly over 400 cu. ft. of gas per bbl. of oil.1 On the other hand, wells are being flowed and using as high as 3000 cu. ft. per bbl. of oil. The cost of compressing gas to 300 or 400 lb. varies from 3 c. to 5 c. per 1000 cu. ft. of free gas. This figure has been obtained from a number of sources and as a matter of fact is the basis of actual business transactions involving gas compression. The cost of lifting oil with compressed gas is thus determined.

Jan 12, 1926

By R. A. Perry

A speiss is an artificial arsenide, sometimes an antimonide, formed in lead smelting, smelting of oxide copper ores, and in some lead-refining operations. The production of speiss is closely allied with the amount of arsenic and metallic iron in the blast-furnace charge, while dross is produced mostly from the copper and sulphur, with varying amounts of antimony, arsenic and nickel. Most speiss is essentially an iron arsenide containing some sulphur, copper and nickel, if these elements are present in the furnace. The recent introduction of the soda treatment of lead drosses has produced a speiss high in copper. Speiss is not miscible to any extent with molten copper, lead, matte or slag. Miscibility increases with temperature. This property of the speiss is clarified in the latter part of this paper. Most speisses are produced in conjunction with matte and their sulphur content points to the solubility of matte in speiss. . Some plants have insufficient speiss to warrant separate treatment. When arsenic is high in the blast-furllace charge, there may be sufficient speiss to tap separately from the first settler. Arsenic From the foregoing, it is obvious that a study of the treatment of speiss would not ,be complete without consideration of arsenic. Inasmuch as perhaps go per cent of the blast-furnace feed may be sinter, a definite knowledge of the properties of arsenical ores and compounds that go in to the roaster and sinter feeds is of value. Lcad smelters obtain their arsenic from ores and concentrates, as well as from flue dusts shipped from other plants, particularly copper smelters. The percentage of arsenic in ores is usually low, although occasional lots of high arsenical products are smelted. These crude ores may be sulphides, as arsenopyrite; or oxides like scoiodite, which carry gold or lead minerals. The small amount of arsenic in the original ores received is greatly increased by a circulating load of arsenic in secondary products at are resmelted for their lead or precious metals. More important than the arsenic present directly in the concentrates treated is that in fumes and dusts that may originate in the blast furnace or sinter plant of the lead smelter, or may come from a copper smelter as lead-bearing converter fume or roaster dust. Thus the lead smelter not only must treat its own arsenic but is compelled to handie that from some copper and perhaps other lead plants. Where copper and lead plants exchange products, each plant may be forced to re-treat part of the arsenic it has shipped ,outside its own confines. Speiss from the lead blast furnace contains chiefly iron and arsenic with some lead, copper and sulphur and often appreciable amounts of gold and silver. If its copper content is sufficient this speiss may be sent to the copper smelter where usually it is treated in the converter and the copper is separated as blister. Much of the arsenic and most of the lead are recovered as converter fumes

Jan 1, 1944

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By J. H. Wright

Longhole sublevel stopes excavate ore with which the production geologist has only remote contact; therefore, predicting grade and tonnage from such a stope can be a problem. However, the longholes themselves yield data that can be used to improve those predictions. Here, a radial distribution method of weighting sample data is discussed, which is useful in forecasting grade and tonnage from certain longhole sublevel stopes.

Jan 1, 1985

By Walter S. Weeks, Vitaly S. Grishkevich

Considerable difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be vl. The total head at the outlet is then h + „"• The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Left be the friction loss in the straight duct, s the shock loss in the dif- fuser, and v2 the velocity at the end of the duct. Then ig. 1.—Fan on duct. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established. We may look at this problem in another way. The static pressure at the outlet of the fan is the static pressure of the fan and it is also the static resistance of the duct from that point to the end. The friction in the straight duct is f. If the duct were the same area as the fan outlet, would be the static resistance of the whole duct system. In the present case, however, this resistance is decreased by the change of velocity head into static head in the expansion piece. If conversion were perfect, the static pressure recovered would be

Jan 1, 1931

One session of the annual meeting of the American Society of Civil Engineers-the first since this society became a Founder society with representation on the Board of the United Engineering Society-was held on Jan. 17, 1917, in the Engineering Societies' Building. Mr. Charles F. Rand, Past-President of this Institute, and President of the United Engineering Society, welcomed the new Founder society in the following words: "As one who has looked forward very earnestly to this clay, and who has made a modest effort in favor of the new arrangements, it is a peculiar satisfaction to be the representative of the Trustees of the United Engineering Society and to welcome you on the occasion of your first meeting in this building in which you now own' a quarter interest. "'As this is your annual meeting, I cannot take your time for extended remarks, yet it seems proper that I should call attention to a few facts respecting the United Engineering Society, with which you are now identified. "The United Engineering Society exists for the purpose of holding the legal title to certain of the property of the societies of Civil, Mining, Mechanical and Electrical Engineers and to act for them in certain matters. "The value of its property, including real estate, the Library and the Reserve and Endowment funds, exceeds two million dollars, all free and clear. "The total membership of the four Founder societies is 29,000 and the membership of associate societies is 23,000, making a grand total of 52,000 engineers who now have headquarters in this building.

Jan 3, 1917

By C. R. Johnson, R. A. Greenkorn, G. W. Widner

This paper describes a short, simple well-testing procedure evolved from unsteady-state concepts to appraise wellbore damage in water-input wells. Input rates are changed at specific intervals over a 30-minute period and the wellhead pressure recorded at the end of each interval. From these data, the pressure drop due to the "skin" can be computed. This pressure drop in terms of psi/B/D of input rate is referred to as the "skin factor". Two of these variable-rate tests are required to determine change of wellbore damage and to evaluate well-treatment techniques. There are several advantages to the variable-rate procedure. The necessary data can be obtained with wellhead gauges and meters. There is little interference with normal operations. The short testing period eliminates many interpretative difficulties that come from interference from adjacent wells. The shut-in period required for standard tests before the plot of pressure vs log of time attains a straight line is often 12 hours or more. Such a time period is incronvenient, especially when a well must be tested repeatedly to evaluate change in wellbore characteristics. This variable-rate procedure has been successfully npplied to water-input wells in three fields. For some of the wells, skin factors were calculated from both the standard and the variable-rate tests. These results show good agreement. THEORY OF THE VARIABLE-RATE PROCEDURE In many waterflood input wells, the pressure in the wellbore differs from the pressure in the reservoir immediately adjacent to the well because of the restriction of flow through the skin of the well. If the true pressure of the reservoir at the well, p,, is that pressure which would exist in the well if no skin were present, and p,' is the actual pressure as measured in the well, this difference, is the skin effect. Fig. 1 shows the change in skin effect with change in flow rate. As the flow is reduced, the skin effect is reduced by an amount equal to the change in wellbore pressure minus the change in reservoir pressure. The equation of pressure change without skin using the point-source solution of the diffusivity equation is (after van Everdingen')

By H. N. Hickey

Wildcat drilling operations in Montana during 1933 did not yield any discoveries of oil or gas that were of major importance. There was comparatively little drilling in the older proven fields, as most of the interest was centered in the Cut Bank field, where 44 wells were completed. The total number of wells completed in the state during the year was 79, of which 62 were productive of either oil or gas.

Jan 1, 1934

By C. W. Reith

The development of production in West Texas during the year 1933 was largely confined to the expansion of proven areas, especially Ward County, Iatan and North Winkler. Wildcat activity was at a comparatively low ebb and resulted only in discoveries of probable minor importance in Ector County. The interest shown in deep wildcatting to test beds of pre-Permian age was a new development, which should soon throw light on the possibilities of deeper production from the present producing fields. The important pre-Permian tests of the year were: 1. Stanolind Oil and Gas Co., Todd No. 1, a unitized test, in north central Crockett County on a probable continuation of the Big Lake trend. The well encountered several showings of oil and penetrated an Ordovician section very similar to the productive zones at Big Lake, but was abandoned when sulfur water was encountered at 8041 feet. 2. Gulf Production Co., McElroy No. 103, in the McElroy Field, Upton County. The well was drilling at 8553 ft. at the close of the year in beds of probable pre-Permian age. The test is an important one because it should prove or disprove deep production in the Church-Fields-McElroy pools and also throw geologic light on the deep possibilities of other fields in the western part of the Permian Basin. 3. Humble Oil and Refining Co., White and Baker No. 1, in Pecos County, about 11 miles west of the Yates field. The well is on a nonproductive Permian high and should indicate the deep possibilities of the Yates field. At the end of the year, drilling had progressed to 7200 ft., where beds of pre-Permian age are believed to have been penetrated. The major fields in West Texas, in which present-day proration had its inception, were produced under increased restrictions. A date of importance in the proration history of the area was $ept. 8, 1933, when the Railroad Commission issued an order placing all producing wells under proration. The severe reductions in total outlet made during 1933 were well compensated for by a more than threefold increase in the price of crude oil. Acid treatment was one of the general engineering developments of interest. The work had not progressed sufficie~ltly at the close of 1933

Jan 1, 1934

By K. C. Gilbart, Edgar Stansfield

When plants decay in a peat bog the woody parts form a brown pasty mass, or peat muck, largely soluble in alkalis. This brown matter has been termed "ulmin." The same material, but commonly black in color, is found in coal, and there is evidence of the similarity between the material forming the main bulk of the coal and the bulk of the more recently decayed material in peat bogs. The more recent or low-rank coals, such as lignite, little removed from the peat stage, contain notable percentages of alkali-soluble ulmins, but the percentage decreases with increased degree of coalification and is negligible in bituminous or higher rank coals. The determination of the alkali-soluble ulmins in any coal gives, therefore, an indication of its degree of coalification or rank. Coals which contain few or no ulmins soluble in alkalis do contain ulmins which can be rendered soluble by oxidation. The higher the rank of the coal, the more difficult it is to oxidize the insoluble ulmins and make them soluble. High-rank coals can be differentiated by oxidation tests on the insoluble ulmins; but low-rank coals can be characterized by both their soluble and insoluble ulmins. This paper deals with the determination and significance of the alkali-soluble ulmins present as such in the coal. The chemical nature and composition of ulmins are not discussed. Review of Literature The history of the study of ulmin is well given by Stopes and Wheeler.' The action of potash on coal has long been known, as Braconnot in 1819 distinguished between lignites and bituminous coals by stating that the former gave colored solutions with potash. Later the intensity of color was used to give a fuller differentiation. Hoffman2 distinguished between lignites and lignitic coals by the darker color given by the

Jan 1, 1932

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By Alexander Anderson

TABLES showing the drift and inclination of wells surveyed in the years 1924 to 28' and in the year 1929' have already been published. Each of these tables included a little over 1,000,000 ft. of rotary hole. In the year 1930 the table -shown-in . Fig. 1, comprising, the results of surveys .of 1,030,344 ft. of hole and representing 11,642 individual survey readings, was compiled. For that purpose we selected 'I only wells that had been drilled in California during that year. The footage of Fig. 1 differs from the two earlier tables in that the wells were all drilled in the year 1930. In the earlier tables, the footage shown was surveyed in the years designated, but some of the wells were drilled in earlier years.

Jan 1, 1931

By M. D. Voegele, C. Fairhurst

INTRODUCTION A computer study of excavation support loads in tunnels and other excavations in discontinuous rock masses was undertaken with the distinct element method introduced by Cundall (1971). In the distinct element method the rock mass is modeled as a composition of individual blocks of rock defined by the joint planes. Normal and shear deformation laws are ascribed to the joint surfaces; the blocks of rock themselves are considered to be rigid. The particular version of the program utilized in this study ran a mini computer and used inter, active techniques for the input of geometrical data such as joint orientation and spacing and subsequent display of rock mass deformation and other data. Two major aspects of the behavior of excavations in jointed rock masses are examined in this paper: i) the behavior of unsupported excavations in rock masses with varying joint configuration, joint properties and in situ stress fields; and ii) the modification of the behavior of similar excavations when support is provided. In the latter case the excavation behavior was examined through the use of ground reaction curves. THE DISTINCT ELEMENT METHOD The Distinct Element method introduced by Cundall (1971) is a computer based analysis that simulates the behavior of a system of discrete, semi-rigid rock blocks. Block interactions are governed by realistic friction and stiffness laws; each block may undergo unlimited displacement and rotation while progressive failure is modeled.

Jan 1, 1982

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 8, 1979

By Alfred Weiss

Approximately 850 delegates from 24 countries met in Tokyo, Japan, May 24-27, for the second MMIJ-AIME Joint Meeting in 55 years, to exchange technical knowledge and experience in the fields of exploration, mining, metallurgy and petroleum engineering. The first such meeting was held in 1917 in Kyoto, Japan. Although the Mining and Metallurgical Institute of Japan was the sponsor, the entire meeting (machinery exposition, technical program, and tours) was a joint effort of the two institutes.

Jan 7, 1972

By Ingersoll Olmsted

Mr. D. H. BRowne's paper upon " The Distribution of Phosphorus in the Ludington Mine" (Trans., xvii., 616) has interested me very much, and perhaps I cannot give a better proof of that, interest than an account of my work and observations in the same direction while chemist of the Hudson River Ore and Iron Company. The ores of this company lie in a chain of low hills running northwest and southeast, about three miles back from the eastern bank of the Hudson river, below Hudson, N. Y. They occur in thick veins, with the characteristic Hudson river slate formation as hangingrock and foot-wall, and dip about 45' east, outcropping in many places near the top of the western slopes.

Jan 1, 1890

By John Freeman

THE die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the, minimum amount of scrap to be sheared from the pressing as it comes from the-die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By F. W. McQuiston

Idarado Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934