Search Documents

By S. H. Ash

Foreman remains key man in any safety program, as men attracted to the industry must be trained in safety thinking. Diesel engines underground aid safety and widespread use of roof bolting is reflected in reduction of roof-fall fatalities.

Jan 2, 1953

By Charles Legrand

The problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of installation is greater with electric pumps than steam pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic packing instead of soft packing, if the water is not too gritty or the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer, and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid water, both plungers and puhp bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressures on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old Dominion Copper Mining & Smelting Co., Globe, it was found that a small air ejector discharging into a mine car provides a very convenient way to clean mud and sand from a sump.

Jan 1, 1916

Transit A light weight, totally enclosed theodolite, especially designed for mining, has been placed on the market by Askania Werke, A. G. The instrument weighs only 41/4 lb and measures 51/8 x 71/2 in. without tripod and in a waterproof aluminum hood. It may be mounted on tripod or bracket without removing the protective hood. [ ] Standard equipment includes diagonal eyepiece rotating in all directions which eliminates need to be in line with scope for sighting and makes an auxiliary scope unnecessary for steep sights. The transit reads direct to 1 minute and may be estimated to 6 seconds by means of optical micrometer on both horizontal and vertical circles. The telescope in vertical position serves as optical plummet, sighting through an opening in the base. The instrument is shown above mounted for attaching to a pin driven in timber or rock, eliminating tripod or set-up bar in cramped quarters. The chain clamp in the lower picture is used on timber or steel ground supports. Complete with carrying case and set-up brackets, ready for use in a raise, it weighs less than 6 lb, and the protective hood remains on until the instrument is securely mounted. [ ] Accessories for increasing versatility of this mining theodolite are: tripod, electric illumination for optical micrometer and reticule, close range objective lens, and objective lens prism for sighting vertically in front of the instrument. Circle No. 1

Jan 1, 1952

By W. T. Thom

ALL engineering education is faced by certain basic problems, three of which seem to have particular present importance in geological engineering training in general, and in respect to training for oil field geoexploratory work in particular. PROBLEM I The first of these problems has to do with present and future educational objectives and with the numbers and qualities of the men who should be coming out of our geoexploratory training programs. Before the war we needed ever-increasing numbers of graduates at the Bachelor's level and a very much smaller number of men who had reached the Doctorate degree. Now, with more difficult, more extensive, and more costly exploratory work; with a rapid expansion of company "staff" activities, and with the initiation of many new research organizations and laboratories; it is clear that men of exceptional ability will be more and more in demand, and that the schools will need to carry a greater proportion of their students through to the Ph.D. degree. PROBLEM 2 Assuming that the mineral industries will need an increasing supply of well-qualified Ph.D.s for future geoexploratory work (staff, line and research), can the schools expect to provide this supply of able Ph.D.s merely by expanding the proportion of B.S. and B.A. majors who go on through to the doctorate stage of training? And the answer is definitely "No "-as the situation stands at present. Most A.B. graduates are years short of the preparations in basic science and elementary engineering prerequisite to effective graduate study in the geoexploratory fields (paleontology excepted), and similarly many of the annual crop of B.S. graduates lack adequate training in English; in ancient and modern history; and in the modern principles of labor and public relations. Indeed, several basic problems of undergraduate curricular organization and integration remain to be solved before most recipients of a Bachelor's degree will have that sound and broad educational foundation prerequisite to graduate training on a really effective basis. It is for these reasons that we have continued to experiment with our geological engineering program at Princeton, in an endeavor to provide a pilot-plant demonstration of a suitably broad and flexible undergraduate curriculum. PROBLEM 3 But assuming that the schools can and do get undergraduate curricula set up in proper phase and scale to meet needed enrollment quotas for graduate training, what about the most urgent part of our whole mineral-industry educational problem? What about finding and bringing into mineral-industry training those youngsters of superior ability who are, by potential or known inclination, especially well-qualified for geoexploratory work?

Jan 1, 1947

By J. J. Pelley

NOT being a scientist, an engineer or a metallurgist, I consider it a very great honor indeed to be asked to address the American Institute of Mining and Metallurgical Engineers. Your program indicates that any lack of intricate and technical knowledge on my part in the field of metals will be well taken care of by others. Therefore, I believe any remarks that I have to make might well be devoted to the practical side of metals in railroad service and to the general railroad situation as I view it today. The experiments now being conducted on the railroads with so-called streamlined, light-weight trains and cars would not have been possible had it not been for scientific and engineering research in the past that made these lighter weight metals available. The railroads now have approximately forty units of these new trains in operation. Experi-ence with them will no doubt be a guidepost for future construction in that direction. While the best known experiments are in the passenger service, they are being extended into the freight service. Within the past three years there was constructed for the Association of American Railroads a new standard box car of ordinary carbon steel, in which, by reason of superior design, weight was reduced by 3500 to 4500 lb. under that of existing cars of like capacity. The Association is now testing a box car that weighs approximately six or seven tons less than practically all of the box cars of like capacity in service today. If these tests are successful a very large field for the use of lighter weight metals will immediately be opened, provided the costs of such metals are not too high. The fact that various experiments are being carried on with other classes of equipment constructed with so-called light-weight and non-corrosive metals no doubt will have a considerable effect upon the rebuild-ing of old equipment. The question then will be: How much can we afford to spend on the rebuilding of an old car weighing six to seven tons more than a new car constructed with the latest available materials?

Jan 1, 1936

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By John Fritz

THE John Fritz Medal was presented to Ambrose Swasey of Cleveland, Ohio, in the Auditorium of the Engineering Societies Building, in New York, on April 23. Charles F. Rand, Chairman of the Board of Award, presided and, after speaking very briefly of Mr. Swasey, whose friend he has been for a great many years, ,introduced Gen. William Crozier, formerly Chief of Ordnance, U. S. Army, who spoke most entertainingly of, Mr. Swasey's accomplishments in designing and manufacturing instruments of precision, particularly for the use of artillery in range finding: Dr. William Wallace Campbell, Director of the Lick Observatory, and President of the University of California, described Mr. Swasey's, contribution to astronomical advancement by his notable development of the largest telescopes in this country.

Jan 1, 1924

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By J. H. Slater

THERE is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust con-tains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out, This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage, An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable prod-uct, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates.

Jan 1, 1940

By Radoslav Despotovic

The developed radiometric method of particle system analysis has been applied to investigate the bulk properties of particles precipitated from solutions. The nature and principles of the method applied are described briefly, and some possible models in the field of fine colloid particles precipitation discussed. Changes in radionuclide distribution were followed during the solid phase formation and the data were used to calculate changes in bulk composition of colloid precipitates. The radiometric data show interesting phenomena closely connected with the characteristic of bulk particles. The measured radiometric data are highly reproducible, the applied methods have proved to be sensitive, and the developed techniques have been tested by various standard procedures.

Jan 1, 1980

MELTING in a crucible is the customary method for small things. It is done in two ways: with the blast of bellows and with an air furnace. The one with bellows, which I wish to show you now, is the common method most in use. It melts quickly and is very well known to goldsmiths and to all melters. I could continue without telling you of it, but I shall tell you its method in order to caution you about what you might perhaps not notice. In order to do this, first make a little forge with a pair of bellows that can be worked with one hand or in some other way. A crucible of the size needed is then taken and filled with the material that you wish to melt. Then, on the forge in front of the place where the wind issues from the bellows, kindle as much charcoal as you think will well cover your crucible and put your crucible full of material in the midst of this burning charcoal above the place where the blast strikes the fire, two or three dita distant from the place where the blast issues-or as much more or less as the size of the crucible or the force of the bellows requires. It is allowed

Jan 1, 1942

By R. J. Lytle

Geophysical exploration for engineering purposes is conducted to decrease the risk in encountering site uncertainties. Such studies are needed in construction of underground facilities. Current responsibilities, opportunities and challenges for those with geophysical expertise are defined. These include: replacing the squiggly line format, developing verification sites for method evaluations, applying knowledge engineering and assuming responsibility for crucial national problems involving rock mechanics expertise.

Jan 1, 1982

By Wm. Hamilton Merritt

With the exception of the Vancouver Island coal, all the western coal-fields owe their present development to the completion, in the autumn of 1886, of the Canadian Pacific railroad. While it could not be expected that a very great deal could be accomplished in three years, enough has been done to pretty thoroughly establish the coal-bearing areas and their correspondence with those which have been developed to the south of the boundary along the lines of the transatlantic railroads in the United States. This summer I visited some of the important developments in the coal areas of Washington Territory, largely with the object of being better able to appreciate the corresponding coal-bearing areas in British Columbia to the north. In Western Canada, coal-bearing rocks have been found in three zones: 1. In the plains to the east of the Rocky Mountains and in the eastern flanking ranges, the coal occurs in the Cretaceous formation (including the Laramie). 2. In the interior plateau of British Columbia, the coal is found in the Tertiary formation. 3. On the coast of British Columbia, Cretaceous and Tertiary rocks are found carrying coal, and on the Island of Vancouver the well known Nanaimo coal has been worked for years in the first named formation. In all of these zones, the coals vary from lignites up to higher grades, the factor determining quality being the amount of pressute to which they have been subjected. The intensity of this pressure is generally shown by the disturbance which the coals exhibit, and, in many cases, is almost directly in proportion to the distance of the deposits from mountain ranges. This seems to be also the opinion expressed by Mr. Bailey Willis in connection with his Census Report on the coals of Washington. It has been elsewhere stated

Jan 1, 1890

By H. L. Washburn, G. L. Judy

DURING recent years thermal drying of fine coal has increased at a tremendous rate, but very little discussion of the several excellent units has found its way into print. This is particularly true for operating and maintenance costs, and the operator who is faced with his first fine coal drying installation must depend chiefly on hearsay when trying to determine what his drying costs will be. This article presents the maintenance and operating costs for the seven drying units now installed in preparation plants of Pittsburgh Consolidation Coal Co. and lists other cost information that should be obtained before any particular drying unit is selected.

Jan 10, 1957

By C. S. Smith

The partial persistence of grain size and grain shape on melting and resolidifying crystalline substances, as well as the general effects of pre-solidifi-cation and of superheating on nuclea-tion rate, have been attributed to the presence in the liquid of crystalline impurities bearing some structural relation to the principal solid and hence capable of serving as nuclei for its crystallization. That such lattice matching does sometimes occur is well established, but it is surely improbable that a compound possessing both high-temperature stability and the requisite structural similarity should be naturally available in almost every system. It is now suggested that a mechanism for producing appropriate nuclei exists in the crystallization of all but absolutely pure substances. Impurities can he of many kinds. Some will give rise to compounds that are less soluble in the solid crystal than in the liquid. A . crystal forming from a melt or solution containing these will be supersaturated in some degree, and the foreign atoms will commence to segregate during or after solidification. They do not necessarily form pure, unstrained, crystals of the precipitating compound with its normal composition and structure. Generally—at least in the metallurgical examples that have been most studied —the first recognizable nuclei have lattice coherency with the surrounding matrix and have practically the same crystal structure and lattice spacing as the material in which they form, differ- ing only in composition. An extremely thin oxide layer formed under appropriate conditions on or in a solid metal will tend to be coherent with the metal lattice, and the first few atom layers of the oxide in contact with the metal will differ in both composition and structure from massive crystalliue oxide. It will resemble the metal more closely than the oxide. If it did not subsequently change on melting, such an oxide film would constitute an almost perfect "template" or two-dimensional matrix to hold a few atoms of the primary metal in the exact array needed to form a nucleus for solidification. Any precipitating material will adopt the correct spacing over a few atom diameters, and with appropriate substitution of other atoms of the correct sizes a precipitate can match the parent lattice over large areas of cohererlce without excessive strain. In metals, the componentsof a host of oxides, silicides, borides, nitrides, carbides, sulphides, and other compounds are always present in minute amounts. Some of these will be eliminated because of extreme insolubility in the liquid, while others will remain soluble in the solid; occasionally, however, particles will be formed in the solid by coherent precipitation—not of pure substances, but of whatever assortment of atoms best satisfies the joint requirements of availability, affinity, and appropriate average atom size. Of these, many will disappear on melting, but a few will persist unmelted as little rafts of complex composition, maintaining in the liquid a surface of the exact geometry needed to nucleate the solid on subsequent cooling. Their number and size distribution will determine the resulting grain size; the dimensions of the largest will determine the degree of undercooling that can occur before solidification commences. A similar process may operate in the case of phase transformations in solids. The coherent precipitation of supersaturated minor constituents in a low-temperature phase should facilitate the nucleation of this phase on subsequent cooling after transforming into another phase at higher temperatures. At first sight this hypothesis may seem little different from the older ones. It should therefore be emphasized that it does not depend on chance to provide the right compound to form a nucleus, but postulates that every crystal, containing minute amourlts of any of a wide range of impurities, automatically engenders particles having the correct surface structure to serve as nuclei for subsequent solidification. It could operate in any system, metallic, organic, or inorganic. The suggested mechanism is closely analogous to the production of antibodies from antigens in living organisms—indeed, it was a description of the matrix theory of this process that suggested to the writer its crystalline analogue.

Jan 1, 1950

By M. C. Fuerstenau, D. W. Fuerstenau

Long-Chained aliphatic amine salts have been used for the separation of sylvite (KC1) from halite (NaC1) by flotation. It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin as postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the –NH3 group in the amine, floats potassium chloride because the dimensions of this group as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it.

Mar 1, 1956

BEFORE I go any farther, I wish to show you the different kinds of guns, as I have been able to understand them from the finished works, for no one is found to have written or spoken of this. To my knowledge, it is not universally known who was the inventor of this horrible and fearful instrument. It is believed that it came from. Germany, discovered by chance at least three hundred years ago, according to Cornazzano, * from a crude and small beginning like the printing of letters. I believe, .indeed it seems to me certain, that guns evolved from the effect of powder, and then the forms were varied and changed according to the desires and different abilities of those who made or wished to use them. †

Jan 1, 1942

By Robert E. Green, Edmund G. Henneke

The velocities of the three possible modes of elastic wave propagation have been calculated for single-crystal copper at 1-deg intervals throughout the standard stereographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy flux and specimen axes are presented as arrows drawn on stereographic projections. The orientation factors associated with dislocation motion on the primary slip system only and also on all twelve slip systems have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing wave resonant specimen have also been calculated. The results of these calculatians are compared with earlier calculations on aluminum crystals and the relevance of these results to ultrasonic attenuation measurements is discussed. GREEN and inton' have recently outlined a procedure for determining the orientation factors for dislocation damping in single crystals. The stress field associated with a given mode of elastic wave propagation is resolved on the slip systems in which it is assumed the dislocations are vibrating due to this stress field. Since, at room temperature, slip has been observed on a limited number of systems in fcc and hcp metal crystals, it is assumed that these systems are the appropriate ones to use for the resolving process. This procedure has been applied to aluminum crystals by Hinton and hreen' and to zinc crystals by Henneke and Green.3 In the present paper the modes of elastic wave propagation have been calculated for copper crystals possessing orientations at 1-deg intervals throughout the standard stereographic triangle. The deviation of the energy flux vectors from the specimen axis have been calculated for each mode. The stress field associated with each mode has been resolved on the (111)(110) slip systems in order to determine the orientation factors for dislocation damping. MODES OF ELASTIC WAVE PROPAGATION For any direction in a linear homogeneous aniso-tropic material three elastic modes can be propagated. In general, each of these modes has both longitudinal and transverse particle displacements associated with it and thus are not "pure" modes. However, there is always one component which is greatest in either a longitudinal or transverse direction and hence the mode may be referred to as quasi-longitudinal or quasi-transverse, accordingly. For certain axes of high symmetry pure modes may be propagated. The phenomenon of refraction of the energy flux vector is also exhibited by elastic wave propagation in ani-

Jan 1, 1969

By Oliver Bowles

SUPERFLUOUS varieties and standards which are meriting the critical scrutiny of the manufactur-ing industry have a special significance in the non-metallic mining industries, where, many of the final or intermediate products are manufactured at the mine or quarry. Such processes of manufacture must be considered an integral part of mining in its broader sense. Improvements may be either elimination or standardization. - The chief requirement of elimi-nation is an agreement between consumers and pro-ducers based on facts deduced from: statistical data. Standardization is much, more complex. Standards .may be established only when a very; thorough knowledge has been gained of the physical and chemical properties of the products, and the requirements of consumers. The activities of the Bureau of Standards are. largely directed toward such determinations. Paving-brick manufacturers, together with highway engineers, representatives of certain engineering socie-ties, and Government bureaus, have agreed that of the 66 styles of paving brick on the market 11 only are, essential and 55 are superfluous. Steps have been taken to reduce the output of -all but the 11 standard types. It is customary for manufacturers of structural slate to prepare it in sizes specified by builders and architects. Thus the material cannot be manufactured in advance and the result is irregular activity of mills, delays in filling orders, etc. To improve this condition, the Structural Slate Co. has issued a series of pamphlets giving complete specifications of structural slate for various purposes. Architects find it so much easier .to, order slate from these sheets that standard sizes are specified in preparing plans for new structures. Slate switchboards are usually manufactured after. the order has been received. One manufacturer claims that 80 per cent. of all switchboards are of standard sizes, and he keeps such sizes in stock. The facility with which orders may be filled from stock, and the improved quality of seasoned switchboards, will undoubtedly influence electrical, companies toward a more uniform standardization in size. Simplicity, could be further attained by the elimination of minor irregularities in .style; for example, in the beveled. edges.

Jan 2, 1922