Search Documents

By C. E. Meissner

The need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. Furnace Design There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the check-ers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped unti1, the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace. The slag pockets and checkers are cleaned by digging down to arched openings which have been bricked up.

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district's largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By P. W. Allen

Here are the facts and the figures on how Tahawus cut costs and improved safety in solving their secondary breakage problem - A dropball crane entirely eliminated secondary blasting.

Jan 4, 1953

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists' Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention' to this subject had been crystallized by a symposium held by the Faraday Society in 1925. ' After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country... . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on `Basic Open Hearth Steelmaking'." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circumstances which led to the publication of "Basic Open Hearth Steelmaking" in the spring of 1944. The book consisted of nineteen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, B. M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1951

By E. William Heinrich

With the mounting emphasis on unconventional energy sources, total consumption of lithium minerals will increase significantly in the next decade. The recent development of the lithium battery, for example, may greatly boost the demand for lithium metal. At the same time, the growth in the ceramic, glass, and chemical industries is bound to increase the demand for lithium minerals. In fact, the entire consumption or utilization breakdown of lithium minerals will change considerably from its current pattern. Briefly, today's market for lithium minerals' can be grouped into three categories: (1) Lithium concentrates. Accounting for 57% of market use, these concentrates are beneficiated Li-A1 silicates for ceramic, glass, and glass-ceramic raw materials. The concentrates are chiefly spodumene; inverted iron-depleted beta-spodumene; and petalite or its isochemical decomposition product spodumene + quartz intergrowth ("squi"). In the past, lepidolite has also been used.

Jan 9, 1974

By Joseph Singewald

THE problem of the utilization of the low-grade red iron-ores has peen before the iron-mining industry of the South for several decades. the experiments by W. H. Coghill1 of the U. S. Bureau of Mines to determine the degree of liberation of minerals in the Alabama low-grade red iron-ores after grinding interest the writer very much because 10 fears ago, while a member of the U. S. Bureau of, Mines, he experimented similarly on the same ores using a heavy solution .2 Extensive experiments were made in the nineties by W. B. Phillips3 in association with H. A. J. Wilkens and H. B. C. Nitze. The ores were rushed to pass 15 mesh and were separated by magnetic machines into concentrates, middlings and tails. The experiments were made with carload lots in an experimental mill. Most of the ores tested, however, were soft, whereas the main problem is the utilization of the low-grade hard ores. Phillips gives the results of only four tests of hard ores; two of these are of self-fluxing ores of the grade now utilized and two of ower grade and less amenable to concentration than the average low-grade ore that underlies the self-fluxing ore of the Big Seam. The average of these least favorable samples shows the production, from an ore analyzing 32.30 per cent. Fe, 10.34 per cent. CaO, 33.40 per cent. insoluble, of a concentrate with 43.82 per cent. Fe, 8.90 per cent. CaO, 18.48 per Sent. insoluble with a ratio of concentration of 2 and an iron recovery of 39.2 per. cent. The grade of this concentrate compares favorably with the average grade of washed brown ores of the district which is given by Burchard4 as 45 per cent. Fe, 14.6 per cent. Si02. The slightly lower iron

Jan 2, 1927

By D. S. Choi, H. von Schonfeldt, H. D. Dahl

The design of pillars around a longwall panel in which the effect of the adjacent and worked-out panel is taken into consideration is discussed. A mathematical model is used to duplicate field observations such as opening closure and pillar rib movement. The model is then used to predict the effect of changes in mining geometry on the opening stability.

Jan 1, 1976

By Charles A. Ashburner

The petroleum industry of western Pennsylvania and southwestern New York lias been one of phenomenal development. Greater and more sudden flucuations hare occurred in the price* of crude oil, and in all the collateral interests dependent upon its production, than in the case of any other mineral product which has been extensively exploited in the United States. This was more particularly so from the commencement of drilling for oil in 1859 down to the end of 1877. The experience gained during these early years has enabled the oil men to operate more intelligently since; the business is not now attended with the hazardous risks with which it is generally credited. The most important questions connected with the oil industry are those of (a) the oil-supply, and (6) the possible ultimate exhaustion of the field. Since 1876 my attention has been directed to the study of the statistics of the product of the oil regions. In January, 1880, in order to slow some interesting points connected with these questions, I prepared a graphic chart which was used to illustrate a lecture on petroleum delivered before the Franklin Institute. This chart was afterwards reconstructed in two distinct forms for publication in the census report. on Petroleum and its Products. These latter I have redrawn in a condensed form, and have extended them to include the statistics up to 1885, for publication in the Transac tions of the Institute, in conjuction with a map of the oil-re&'~IOIIS prepared by Mr. John F. CarII and myself. It is hoped that these illustrations will be found interesting to the members of the Institute, and of practical utility to oil-men, without any extended discussion, since it is my desire to make only such brief references to them and give such additional detailed facts as may serve to make the prominent features understood.

Jan 1, 1886

By AIME AIME

THE Institute of Metals held a well rounded out symposium on the working of metals, distributed over two sessions. At the first session* four papers were presented, two dealing with the, cold working of metals and alloys and two with the hot working of non-ferrous alloys. The first paper by E. V. Crane, dealt with "Metal Working in Power Presses." Mr. Crane pointed out the empirical nature of engineering data available for use in calculating the probable stresses developed and power requirements, for the shearing, drawing, binding and other forming operations. He described the various operations, methods of determining stresses developed and presented data obtained. In the discussion C. F. Hammond took exception to Mr. Crane's objections to the rather too frequent. annealing operations in drawing of cartridge cases, pointing out that the material was-manufactured to meet specified structure and physical requirements, which could only be met by carefully controlled sequences of working and intermediate annealing operations.

Jan 1, 1931

By A. J. Shaler, J. Prieto Isaza, J. Wulff

Tantalum metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involwing high temperatures in vacuo some of the refractory metals 6ecome brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element colum-bium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum-columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen-containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides; one of the authors undertook4 an investigation of the thermochemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exo-thermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the Drocess should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonly made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tanta-

Jan 1, 1949

By J. C. McHardy

During 1980-2000, the Florida phosphate industry will deplete its central Florida Polk County reserves. As a result, new mines will be built in the so-called southern Florida reserve areas. These mines will require new mining, beneficiation, and tailings disposal technologies since southern reserves have different characteristics than have been encountered in the central Florida deposits. Furthermore, government regulations will necessitate development of new tailings and clay disposal methods. This paper reviews these challenges for the Phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1984

By Julius Albert Krug

IN the field of mineral resources, today's problems and those we can reasonably expect in the future are so vast that nothing less than world-wide thinking and world-wide planning will suffice. I can imagine nothing more useful for the Institute to do in celebration of its seventy-fifth anniversary than to hold this conference on world mineral resources. Mineral resources are the basis of any nation's industrial production. Without expanding industrial production, the high standard of living found in the United States could not exist. Without such a standard of living it would be most unlikely that we should have a high level of culture. The hope of the world, as I see it, depends very largely on a general rise in living standards everywhere, and in the general increase of the levels of culture including a sympathetic understanding of the problems of other nations. For this reason, the proper use of the world's remaining mineral resources must be taken into account in any plans to safeguard the peace of the world. Being as exasperatingly human as human beings always seem to be,. we usually wait until almost too late to begin our plans to stave off an impending disaster. We do this as individuals, as components of particular States or Governments, and as citizens of the world. We waited, if not too late, certainly a very long time in getting started on the job of world-wide con-

Jan 1, 1947

By L. G. E. Bignell, E. A. Hanson, J. O. Lewis

There was a general upward trend of all petroleum activities in Oklahoma during 1933, especially in the last quarter, though the average price for crude oil for the year was below 1932 and overproduction in East Texas demoralized conditions for several months. As the Federal Agencies established under the National Industry Recovery Act began to function conditions in Oklahoma were visibly affected and production of "hot oil" from Oklahoma City field practically ceased. More oil wells were completed, six new fields discovered, extensive geophysical prospecting carried on in many parts of the state, and an increased amount of clean-out and reconditioning work done in older pools during the past year. To increase quantity and rate of recovery of oil many wells producing from limestone formations were treated with hydrochloric acid. The Oklahoma City field had a reported production of 66,984,570 bbl. of oil during 1933, or almost exactly twice the amount reported for 1932. Potential tests and other indicators show that the wells are rapidly approaching the stage where mechanical lift must be applied to all of them, including the wells in the Wilcox sand zone. The major pipe-line companies serving the oil fields of Oklahoma have been anxious to make connections to all wells during 1933 and have indicated a willingness to accept all oil available. The amount offered has been restricted by proration orders, but the state did produce 178,356,-449 bbl. during the year, an increase of about 18.6 per cent over 1932. This increase was practically all due to the greater demand for Oklahoma City oil, as all other pools of any importance showed loss in production or very small gains last year. The U. S. Bureau of Mines' laboratory reports the lubricating distillate content of Oklahoma City crude from Arbuckle and Lower Simpson formations about 17 per cent by volume. East Texas oil is reported to contain about 5.6 per cent lubricating distillates. The desire of the transportation companies to keep their equipment operating at maximum capacity and the need of some refineries for more

Jan 1, 1934

By J. H. Nead

The subject of this paper is one to which there are many references in the literature but on which few actual data have been published. Such data are here presented showing the absorption of sulfur from producer gas in two open-hearth heats. This absorption occurs during the melting-down stage. Results of analyses of slag and metal samples taken simultaneously from the bath are given. THE subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. Inmost other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to, determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were taken every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in

Jan 2, 1924

By William Kelly, Frederick Laist

The slow, tedious and costly method of reducing copper matte to metallic copper in the reverberatory furnace, commonly known as the Welsh process, was displaced by the rapid and inexpensive converter process about fifty years ago. The art of refining copper was for many generations a carefully guarded secret among the Welsh furnacemen and was handed down among them from father to son. An attempt was made to apply it at Butte when the smelting of copper ore first started there but it proved too difficult and expensive under local conditions, and until the introduction of the converter process the entire output of copper was shipped to Swansea in the form of high-grade (60 per cent) matte. Before the construction of the Manhes converter, attempts had been made to reduce copper matte in the bessemer steel converter, but these failed, chiefly because the air was blown through the bottom of the vessel. The air holes became clogged with chilled copper as soon as the reduction started. Manhes partially overcame this difficulty by placing the tuyeres in the side of the vessel, some, distance above the bottom, thus allowing space beneath them for the copper to accumulate. Nevertheless the first attempts to operate such a converter at Butte were not successful, as no means had been provided for clearing away obstructions, which formed to some extent in front of the tuyeres. This difficulty was overcome by drilling holes in the outside wall of the air chamber directly opposite the holes in the shell and lining, so that these could be punched

Jan 1, 1934

By William Kent

DURING the discussions at the Philadelphia meeting in February last, † several speakers expressed their doubts of the general accuracy of chemical analyses of steel made by "iron works chemists," and especially of determinations of manganese. Since the meeting,. the discussion of the "practical value of chemical analyses" has been continued at some length in the columns of the Iron Age. †Transactions, vol. ix, p. 529.

Jan 1, 1882

By Robert C. Bates

Published information on costs of radon daughter control in uranium mines was analyzed to develop estimates of the cost per ton for any level of radiation exposure control. All data were converted to 1967 cost of living index to provide a common analysis base. Re- of the analysis show that the cost per ton increases exponentially as the radiation level is lowered. A linear relationship with the cost of living index is assumed, and equations and graphs are provided to estimate control cost per ton for any exposure control level and cost of living index.

Jan 1, 1982

By Walter E. Lewis, Robert L. Marovelli

Underground support has a long history as evidenced by Agricola's general description in Dc Re Metallica:1 "The timbering of these openings is done as follows: stulls are set at intervals into hitches in the hanging and footwall, and upon them smooth poles are laid continuously; and that they may be able to bear the weight, the stulls are generally a foot and a half thick. After the ore has been taken out and the mining of the vein is being done elsewhere, the rock then broken, especially if it cannot be taken away without great difficulty, is thrown into these openings among the timbers, and the carriers of the ore are saved toil, and the owners save half the expense. This, then, generally speaking, is the method by which everything related to the timbering of shafts, tunnels, and drifts is carried out."

Jan 1, 1971

By ANTON GRAY

In considering the possibilities and costs of discovering minerals by exploration. mineral occurrences may be classified roughly according to the size of the target they offer to the various methods that have been used to search them out. This classification is advantageous because the methods of search which might be expected to give results in one case may be totally inapplicable in others. Mineral deposits for the most part have been found in groups, or districts, in which the individual deposits occur under the same general geological conditions and usually contain more or less the same metals. There are, also, what are apparently isolated de- posits, although if the truth were fully known many of these probably would not be isolated. These districts, such as the Belgian Congo copper fields, the California Mother Lode, and the Linares lead district of Spain, form the first division of my classification. The second division is formed of the individual deposits of these districts, for example, Kambove mine in the Congo, the Kennedy-Argonaut vein in California, and the Cruz vein at Linares. The third division consists of the separate ore bodies that make up the deposits

Jan 1, 1949

By D. Jenkins

THE Franklin Laboratory was designed mainly for the analysis of the products from the two concentrating mills situated at Franklin and Sterling Hill, the most important determinations being the zinc, iron, manganese, lime, moisture and silica contents of the ores. Within the last 4 years, however, it has been found advisable to examine most of our supplies, and therefore additional space and equipment was allotted for the examination of such substances as oils, greases, soaps, alloys, fuels, paints, explosives and water. The building as shown in elevation (Fig. 1) and plan (Fig. 2) consists of a main or routine laboratory, an experimental laboratory, a water FIG. 1.-WEST ELEVATION. analysis room and the other accessories such as stock room, library, sampling and drying rooms and office. The main laboratory is further divided into a balance room and zinc analysis room. As the greater part of our determinations are volumetric, good light is a very important factor and with this in view the interior walls of the building were constructed of white enameled brick laid in Keene cement. These also have the additional advantage that they give a clean and attractive appearance to the room. The windows are large, being 76 by 44 in. and even on very dark days the light is good throughout the whole laboratory. Our zinc titration requires a constant light and as, on many days, especially in winter, the light is variable, we installed two Artificial

Jan 8, 1917