Search Documents

By David Reger

ONLY a few small pools of oil were found in West Virginia during 1924. The price of oil was so low that there was no incentive for active effort toward the discovery of new pools or the exploitation of reasonably certain productive areas. At present, several encouraging edge-pool developments are being held in reserve in the hope that a more favorable market is not far distant. In the old pools, wells are being carefully tended; there being little tendency toward abandonment. even in cases where production is temporarily unprofitable. In natural gas, however, the total value of which at the well mouth is now more than that of oil, the year has been busy and profitable. , The decline of old pools, together with the increasing demand, has caused the large operators who carry their gas to the consumer to make great efforts to preserve or increase the rate of production; while the small operators, who sell their product to the large companies at the well mouth, have been stimulated toward the same effort by more favorable prices. These conditions brought about the completion of a greater number .of gas wells in 1924 than in 1923. Few pools of gas have been discovered during the year, the principal production having been obtained in old areas and in the unusually large new territory that was revealed as potentially productive by the drilling of 1923. Some of these latter areas are still without pipelines but definite plans for getting most of this gas are now being executed.

Jan 3, 1925

By C. V. Millikan

When a flowing oil well is being drilled in with cable tools, it is difficult to determine when an additional streak of pay sand is drilled. By placing a gas meter on the gas-release line from the oil and gas separator, any increase in volume of gas that comes with oil production is recorded. In addition to the better knowledge of sand conditions, these data are a valuable aid in determining the size and depth of shots, plugging off water, and estimating ultimate production. The meter also gives a record of operation while the well is drilling in; and if allowed to remain on the well after completion will give information that may lead to a more efficient recovery of the oil from the sand. A VERTICAL cross section of any oil sand will show great variation in porosity and oil content. In some sands, the entire thickness contains oil, the variation being only the degree of porosity or oil content, but more often the pay streaks are distinctly separated by shells or barren streaks. These pay strata vary in number and may be thin or thick. The total thickness of the sand may be several tens of feet while the part containing oil may be only 1 or 2 ft. thick. The amount of production is not proportional to the thickness of the sand but rather the thickness of the pay streaks. If the total thickness of the sand or the amount that can be drilled is small, or if the initial production is small, the depth at which each stratum of pay is encountered can be determined sufficiently accurately for all present economic purposes. However, when drilling through sand of considerable thickness, giving large initial production, especially where conditions necessitate that the production go through the same gas trap with that from one or more wells already producing, it is difficult to determine the depth at which the pay strata are encountered even accurately enough to guide the placing of shots, and small pay streaks are apt not to be recognized at all.

Jan 9, 1925

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By J. Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.' Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years. Before Kaiser Steel acquired the Sunnyside Mines in 1950, about 21 million tons of coal had been extracted. Large areas had been worked out and equally large areas first-mined. As demand for coking coal gradually diminished, extensive blocks were shut down, and during the low production period of the 1930's mining on a very limited scale was confined to a section of the property close to the coal tipple. Following purchase of the property Kaiser Steel developed the mines into a fully modernized operation. The worked out and first mined areas covered about four square miles extending five miles along the strike and up to one and a half miles down dip from the outcrop. The sections with favorable mining conditions and clean coal had been largely extracted under the selective mining system imposed by economic conditions and the lack of cleaning plant facilities. Large reserves remained on the fringes of the worked out sections and in areas under deep cover and difficult roof. There were also considerable reserves in first-mined areas. In recent years much of Sunnyside's daily output of 7000 to 8000 tons has been derived from the partially mined localities. Many bumps have occurred when pillars have been pulled within the first-mined areas and on the fringes. The bumps have been associated with retreating pillar lines backing up against old workings and pillar lines in old first-mined areas backing up against highly stressed oversized barrier pillars surrounded by smaller pillars. In some parts of the property the upper Sunnyside seam was extensively worked in the past, and sizable areas of old works overlie the present lower seam workings. Abutment pressures from barrier pillars and pillar remnants are transmitted to the lower seam, contributing to bumps and squeeze conditions. Cover: The terrain is exceedingly rough, and cover varies considerably over relatively short horizontal distances. For example, at No. 1 mine the 2000-ft cover line is ony 2700 ft from the coal outcrop, and at No. 2 mine the cover over the main hoisting slope increases from 1000 to 2000 ft in a horizontal span of 1200 ft. Cover over the present mining sections ranges from several hundred feet in the valleys to 2500 ft under the crest of the divides. A short distance ahead of Sunnyside's deepest development down dip the cover reaches 3000 ft or more.

Jan 1, 1959

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addi-tion of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work.

Jan 1, 1939

By Alvin L. Langstaff, Harold D. Raymond

The design of entry systems and mining panels in room-and-pillar oil shale mines seeks to optimize extraction while ensuring both short- and long-term stability of mine openings. Important criteria for optimization include the definition of allowable roof spans and minimum pillar dimensions. Factors considered pertinent to the design of roof spans and pillars are discussed in this paper. They include, but are not limited to, physical properties and grade of the oil shale, depth of burial, presence and frequency of partings and joints and adverse effects of blasting. Also discussed briefly are some of the ventilation and production considerations in mine design.

Jan 1, 1984

By G. W. Tracy

The material balance equation has been used for many years by engineers to determine reservoir performance. The use of this equation in general has been twofold: first, to determine the oil-in-place in a reservoir; and second, to predict the future performance. The Schilthuis form of the material balance equation, or one equivalent to it, has been used by many of the engineers. The use of the Schilthuis form in predicting future performance has proved to be laborious in that one generally must make several estimates at each step of the trial and error calculation before arriving at a check of the oil-in-place. A method is presented for expediting the calculations. The Schilthuis form of the material balance has been rearranged into a more useable form. In using the material balance to predict the future performance of a reservoir, it has become common practice to estimate the incremental oil production for each step of the calculation which corresponds to a given pressure reduction. Instead of estimating the incremental oil production, the method outlined in this paper better lends itself to estimating the instantaneous gas-oil ratio. A check of oil-in-place is more easily accomplished by estimating gas-oil ratio since it is less sensitive to small inaccuracies. This method incorporates the same self-checking feature inherent in the Schilthius form. DEVELOPMENT OF SIMPLIFlED EQUATION In the development of the simplified equation, the Schilthuis form of the material balance equation will he used. Substituting in Equation 1 for and rearranging terms In Equation 2, the cumulative oil production (n) is multiplied by a factor which is uniquely a function of pressure. Also, the cumulative gas production (G) and net water influx are also multiplied by factors which are a function of pressure alone. These factors are called and are defined as follows: Using these factors, Equation 2 becomes The equation in this form is easier to manipulate mathematically than any of the previous forms which, have been used. Sources of data for the pressure factors are a bottom-hole fluid analysis and the ratio of initial gas cap volume to oil volume in the reservoir. AID IN DETERMlNING THE ORIGINAL OIL-IN-PLACE Each of the curves and +, have a similar shape. Each is infinite at the bubble point pressure. As lhe pressure is reduced below the bubble point, the

Jan 1, 1956

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

Jan 1, 1964

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer—still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The de-watering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilter-able, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf. Slurries and Flocculants Tested: First of the slurries was the thickener feed from the washed coal section of the Michel colliery of Crow's Nest Pass Co. Ltd., Michel, B.C. As shown by the screen and ash analyses in Table I, practically all this slurry was finer than 28 mesh, and about half the solids were finer than 200. Substantially all material coarser than 200 mesh was clean coal, but the ash content of 20.7 pct in the finest size indicates a moderate amount of impurity. This coal is medium-volatile bituminous in rank. Slurry was also obtained from the Black Diamond washery of Palmer Coking Coal Co., King County, Wash. This underflow of a 1/2-mm vibrating slurry screen is a waste product discharged to a settling pond. As shown by the data in Table I it contained about 20 pct material finer than 200 mesh, which analyzed 77.5 pct ash, indicating a high proportion of clay. The coarser sizes were also high in ash content because of the presence of bone and shale. Black Diamond coal is on the dividing line between bituminous and subbituminous rank. The third slurry, from the washery of Roslyn-Cascade Coal Co. in Kittitas County, Wash., was the underflow of a battery of 8-in. cyclones that is wasted with the coarser refuse from the plant. In both size and ash content this slurry was similar to the Black Diamond, but since it was a cyclone-underflow product, the fraction finer than 200 mesh undoubtedly contained a much smaller proportion of finely divided clay than was present in the Black Diamond slurry. The Roslyn-Cascade coal is high-volatile A bituminous in rank. Initially the slurry samples were stored in the laboratory at a concentration of 40 pct solids. A progressive change in filtration and flocculation characteristics during storage was noted, however, presumably because of progressive disintegration of the clay. After careful testing demonstrated that the slurry solids could be dried and then repulped without changing the original filtration characteristics, this procedure was adopted. The flocculants used were Separan 2610, Kylo 27, Jaguar MD-A, Idaho potato starch, and lime. The lime was used as a slurry, the Separan 2610 as a 0.10 pct aqueous solution, and the other flocculants as 0.50 pct aqueous solutions. The starch was causti-cized with sodium hydroxide before use. As some of the flocculants are reported to deteriorate on storage, new batches of flocculants were prepared every two days. Test Procedure: Fig. 1 diagrams the filter leaf apparatus employed. This consists of a test leaf having an effective area of 0.10 sq ft., a 60°, 8 1/2-in. diam cone to hold the slurry sample, a variable-speed electric stirrer, vacuum gage, bleed line for controlling vacuum, filtrate flask, moisture trap, and vacuum pump. Two filter cloths were selected—Saran SA 603, a monofilament, coarse-weave cloth, and polyethylene PO-801 HF, a monofilament, fine-weave cloth. The Saran was selected to provide maximum cake rate without regard to clarity of filtrate and the polyethylene to provide the best quality of filtrate without regard to cake rate. The test charge for the filtering vessel consisted of 800 g of solids (previously soaked for 24 hr) and

Jan 1, 1960

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

By C. Gutiérrez

Flotation and adsorption studies of ilmenite with technical oleic acid, pure oleic acid, and mixtures of each of them with n-hexadecane have been conducted. From them it is concluded that the depression of ilmenite caused by a too long conditioning time is due to adsorption of the collector onto the fines produced by attrition in the conditioning cell, and that fuel oil is necessary for economic flotation of non-deslimed ilmenite ore. This beneficial effect of fuel oil is attributed to van der Waals forces, of the hydro-carbon chains.

Jan 1, 1978

By E. T. Dumble

Discussion of the paper of E. T. DUMBLE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. .1623 to 1638. E. L. DEGOLYER, Norman, Okla. (communIcatIon to the Secretary*).-Referring to Mr. Dumble's description of the stratigraphy of eastern Mexico, I should like to question the classification of the ?Papagallos? or ?Mendez? shales as being of Cretaceous age and the so-called overlapping of the Papagallos or Mendez shales by the Alazan shales; the classification of the San Felipe series as Cretaceous, and the correlation of the San Felipe series with the San Juan limestones. Mr. Durable apparently recognizes the continuity of the great shale formation by his use of the terms "Papagallos" and "Mendez," as equivalent and interchangeable, since the Papagallos Hills in the State of Nuevo Leon and Mendez Station in Northern Vera Cruz, localities at which the shale formation outcrops, and from which the formation names are taken, are approximately 250 miles apart and on opposite sides of the Tamaulipas barrier. The Papagallos shales (evidently referring here to the northern extension only) are said to be non-fossiliferous and no reason for .their Cretaceous classification is given, though in a previous article' they are classified as Cretaceous because at their northernmost outcrop they "have the same relation toward the overlying Tertiary that the Escondido (Cretaceous) has through its whole extent." The Alazan fossil locality was found by me and the first collections from it were sent to Dr. Dall; about 17 species of marine invertebrates were recognized by him, the fauna noted as having a distinct Pacific tincture, and the age of the formation from which they cause pronounced lower Eocene. The outcrop of the shale formation has been traced continuously from this point by me and my assistants into the Panuco River region, where Eocene fossils are reported at a depth of 1,810 ft. in a well at Topila.2 From Topila the formation has been traced continuously north to the Padilla-Jiminez region in Central Tamaulipas. Lithologically, the formation is fairly constant and though I am only generally acquainted with it north of the Padilla-Jiminez region, until definite evidence of the Cretaceous age of the Papagallos shale in its type localities, or of an overlap, is available, it seems to me more logical to consider the shale formation a single stratigraphic unit of Eocene age.

Jan 12, 1915

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,' and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By W. H. Craigue

The scope of this article covers only the mathematical principles involved in discounting to present worth future expected profits and it is believed answers definitely two questions, which were raised at a recent meeting of the Committee on Methods of Valuing Coal Properties, as follows: 1. The accumulative effect of carrying charges on the value of coal mines showing definitely the number of years beyond which the coal may not be mined at a profit and subsequent to which the possession of any unmined coal will be a liability rather than an asset. 2. The effect on the valuation of coal mines, in the presence of the carrying charges described in question 1, of an increase in plant capacity and production. In general, in considering these questions, it may be stated that the consideration of an increase in plant capacity and production follows as a matter of course after a determination has been made of the year beyond which no profits are to be realized (giving the carrying charges accumulative effect, or in other words capitalizing the carrying charges, as shown hereinafter). For example, if it is determined that any coal that is unmined after 45 years will have no value or less than no value, the question immediately arises as to whether or not a plant should be constructed that would result in a yearly production great enough to extract the entire tonnage in a time less than 45 years, and if so the number of years less than 45 years that would, from a financial standpoint, be the most desirable, all under the assumption that the market for the product or the transportation facilities are such that the yearly production can be increased to the desired amount. Specifically, the carrying charge is considered herein as yearly expense, such as state or local taxes, which are assessed each year against the total tonnage remaining in the ground (or the total coal acreage remaining) at the beginning of the year, at a fixed rate per ton (or a fixed rate per acre) OF a fixed percentage of the assessed value, in the latter case it being necessary to convert such percentage into a rate per

Jan 1, 1934

By Walter Harvey Weed

THE enrichment of mineral-veins as a result of the migration of material from an upper oxidized or disintegrated part of a vein to a lower level, where it is redeposited, is now, I believe, quite generally accepted as one explanation of the occurrence of bonanzas in gold- and silver-veins, as well as that of bodies of high-grade ores in cupriferous deposits.* Vogt has called attention to the fact that there are numerous examples of such rich shoots which are " of exclusively primary character, and dependent upon the laws which governed the original ore-deposition." To this I would add that there are also other examples which are neither of primary origin nor clue to descending waters, but result from a reopening of the veins and their penetration by ascending heated waters whose metallic contents are deposited by reaction with the primary pyrite (and possibly other minerals), forming "secondary" enrichments. My studies of the copper-veins of Butte, Montana, show: That the veins there are of several ages and systems; that the older primary quartz-pyrite veins were reopened by later movements, correlated with a period of volcanic activity; and that they were penetrated by hot alkaline waters carrying copper and arsenic in solution, which were deposited presumably by reaction with the pyrite of the original vein. The enormous development of the Butte deposits, attendant upon the extraction of nearly 10,000 tons of ore a day, has revealed many facts concerning the nature and distribution of the ores. Enargite, the copper sulpharsenate, formerly a relatively rare mineral, is now found to be the chief ore of some veins,

Jan 1, 1913

By A. C. Fieldner

The usual analytical determinations made in analyzing coal are comprised in the proximate and ultimate analysis and the determination of calorific value. The proximate analysis includes determinations of moisture, volatile matter, fixed carbon and ash; the ultimate analysis determinations of carbon, hydrogen, oxygen, nitrogen, sulfur and ash. The proximate analysis is an empirical process, and the results, obtained, especially for volatile matter and fixed carbon, are materially influenced by the method of conducting the determinations. This fact must be kept in mind in comparing coal analyses from different laboratories for classification purposes. Unless these laboratories have followed the same standard methods, differences due to variations in the analytical methods may, in some cases, be large enough to change the classification of the coal. It is unfortunate that the determinations of volatile matter and fixed carbon, which are most used in coal classification, are the two that are subject to the greatest variations. Moisture comes next in the scale of variation. The ultimate analysis is less influenced by method, since it comprises the determination of definite chemical elements. However, even the ultimate analysis is subject to errors, due to inorganic carbon from carbonates and to inorganic hydrogen from water. For these reasons it is evident that the Committee on Coal Classification must be informed on the evolution of methods of coal analysis in America and the average differences in analytical results that may be expected from variations in methods. The committee should be informed also on which methods should be accepted as standard for classifying coal and on the magnitude of the differences in results that may be expected from duplicate samples of the same coal sent to different laboratories for analysis by the same standard methods. It is the purpose of the present paper to provide this information. The subject will be discussed under the following main heads:

Jan 1, 1930

By Percy Gillie

THE Tralee preparation plant, owned and operated by the Semet-Solvay division of Allied Chemical and Dye Corp., is located on the Virginian rail- way, near Mullens, Wyoming County, W. Va., and the mine, which is in the Winding Gulf district, produces coal exclusively from Pocahontas No. 3 seam. The property, comprising 4900 acres, is leased from the Pocahontas Land Corp. Prior to 1930 four separate mines were operated in this tract, some having been started about 1916.

Jan 11, 1953