Search Documents

By W. N. Poundstone

The mining and ventilating system used in development work in the Pittsburgh Seam in northern West Virginia is discussed. The seam conditions and the nature of the accompanying methane gas are described. The type of equipment and the mining cycle will be discussed, showing how they are well suited for very gaseous development work. Face ventilation in development work is possibly the fastest growing problem of the industry. The coal mines of the future will be faced with the prospect of mining from under increasing depths of cover. Consequently, larger and larger amounts of methane gas probably will be found. The Pittsburgh Seam, in northern West Virginia, is an example of an area already faced with this problem. At the present time, most of the development work being done in this seam lies beneath 500 to 1200 ft of cover. The Pittsburgh Seam in this area has always been very gassy—even near the outcrop—and the recent development work has been accompanied with extremely large volumes of gas. In many cases, a single development section has liberated in excess of 1,000,000 cfm in 24 hr. This problem of heavy gas liberation was the chief concern, several years ago, when continuous mining equipment was first considered at Christopher Coal Co. All of us were apprehensive about the liberation that would accompany rapid extraction in a single working place. However, the experience during the past few years has shown that this ability to mine only one place at a time, is actually the key to working this type of coal. With all of the mining or advancement concentrated in one place, the ventilation can also be concentrated. By this it is meant that continuous mining permits the active working place to be ventilated with a maximum amount of fresh air, taken directly from the intake source without first passing another working place. Continuous mining (and a good ventilating system) also permits a much greater concentration of attention or vigilance to the actual working place. There are two things that are very important to the mining of coal having high rates of liberation. First, adequate volumes of air are necessary. Second, and perhaps more important, a mining and ventilating system must be used that will provide an uninterrupted flow of air to every portion of the working section. Liberations of this magnitude take only a few seconds of interruption for a dangerous accumulation of gas to occur. With adequate volumes of air available, the ability to concentrate ventilation more than offsets the concentration of gas emission that is inherent with continuous mining. The mining system used with continuous mining equipment at Humphrey Mine is similar to the system used at many mines in the area for development work. This system is designed to favor ventilation, realizing that other efficiencies are meaningless if the equipment must stop because of ventilation difficulties. This plan is especially well suited to minimizing ventilation interruptions. Basically, the overall plan of mining is to develop headings into virgin coal and encircle or block out large areas. These blocks are generally at least 2000 ft sq. The purpose of this blocking out is to bleed gas from the area before pillaring. Experience has shown this method to be quite effective, even in the most gassy areas. The gas in this field seems to migrate or flow readily from the solid coal into the outside return headings of the development work. The numerous clay veins and slips that are found in the area are extremely good avenues for gas flow. A block of coal, surrounded with development headings, usually bleeds off readily; and since it is cut off from the virgin coal, it is not subject to gas migration, through the seam, from this source. However, the outside return of the encircling development work, adjacent to the virgin coal, may liberate gas for years. This liberation from the outside ribs in the virgin coal is the reason split ventilation is used in development work. If split ventilation were not used, there would, in many cases, be a serious build-up of gas in the intake before it could reach the working face. Fig. 1 shows a typical development section having seven headings. The two outside places on each side are returns, and the three center headings serve as intakes. This section is equipped with a ripper-type continuous mining machine. An off-track loading machine is used to load from a surge pile on the

Jan 1, 1961

Jan 1, 1933

By W. R. Webster

Opinions still differ widely concerning the requirements, chemical and physical, which should be expressed in specifications for steel rails, in order to secure results satisfactory to both manufacturers and purchasers.

Jan 1, 1902

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

Pennsylvania has been a leader in the pageant of industrial America because of her natural mineral re- sources, geographical location, and the ingenuity and industry of her citizens. Brick and other clay products were manufactured in Philadelphia in William Penn's time. Ores of iron, zinc, lead, and copper were mined and smelted in eastern Pennsylvania long before the Revolution. Coal was mined on a commercial basis in the anthracite region as early as 1820 and in the bituminous fields in 1830. The first canals and railroads were constructed to transport minerals and mineral products. Oil was struck at Titusville in 1859. A significant event occurred in 1855-the establishment of the Farmers' High School-Pennsylvania's first attempt to provide higher education for its youth. The Farmers' High School included instruction in geology, mineralogy, and assaying. In 1859 the laws of Pennsylvania transferred to the School the state geological and mineralogical collections formerly located in Harrisburg. Well-informed people are familiar with the effects of the Land-Grant Act of 1862. With inspiring words it established state institutions of higher learning where "the leading object shall be, without excluding other scientific and classical studies . . . to teach such branches of learning as are related to agriculture and the mechanic arts . . . in order to promote the liberal and practical education of the industrial classes in the sev-

Jan 1, 1950

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By Thomas W. Wälde

BACKGROUND Foreign investment has been a major factor in bringing about the substantial mining industries of Chile, Peru, Bolivia, Venezuela, Brasil and Guyana. But economic nationalism and sentiment against foreiqn domination of vital national industries grew in the 1960s and most major mining projects were transferred into state owner ship. Among the state mining enterprises formed were CODELCO - Chile, MINERO-PERU/ CENTRCMIN - Peru, CCMIBOL - Bolivia (in 1952), Hierro-PERU, GUY-BAU/BIDCO - Guyana, etc. New investment during that time was discouraged because it was subject to the restrictive conditions of the investment regulations of the Andean-Pact, a grouping of Chile, Bolivia, Peru, Ecuador, Venezuela and Colombia. The philisophy was that mineral resources were to be developed exclusively by national enterprises. Essential foreign inputs had to be acquired "depackaged" as separate purchases of equipment and technical assistance services. As a result of the worldwide economic recession which hit the mining industries in 1980-1982, many projects that were viable in 1970 were not developed by the new state enterprises due to lack of capital, managerial and technical abilities and due to problems with marketing. As a consequence of the long-term decline of metal prices, governments experienced difficulty in getting investment organized through national or foreign enterprises and have had to face up to the trade-offs between national control and active mineral development. A change has since taken place in governmental policies. The 1981 Peruvian mining law, the 1982 mining law of Uruguay, the 1979/1980 mineral promotion laws of Argentina, all witness the gradual shifting of emphasis from restriction to promotion. The investment rules of the Andean Pact have been progressively softened through national regulation and today are more or less irrelevant. Nationalizations and forced renegotiations have not occurred in the last few years. Countries have gone to great lengths (without much success) to re-attract foreign investment on terms that accommodate the political sensitivities of the South American countries and the practical requirements of investors and financiers. For this analysis, three contracts have been selected which reflect this accommodation in three South American countries, where miner a1 production plays a major role in the national economy. These con tracts reflect both the attitudes and traditions of the individual countries, but also mark the shift in mineral investment policies that has taken place. EL INDIO AGREEMENT The 1977 investment agreement between Chile and St. Joe Minerals marked a dramatic relationship between Chile and foreign mining investor s. In Chile, mining of copper has played a major role in the country's history. Large scale copper mining was initiated and developed by Kennecott and Anaconda. The nationalization of these two companies under the Allende government in July 1971 started a wave of nationalizations of foreign-held mining and petroleum operations since then in many parts of the world. The military government supported the new Chilean state mining companies ((30DELCO and ENMI) , but it also attempted to accelerate mineral development by prom ting foreign private investment, thus reversing the nationalistic policies followed by the Allende and the preceding Frei government. The new policy by the military government is expressed in Decreto-Ley 600 (1974) which governs foreign investment in Chile. Decreto-Ley 600 is

Jan 1, 1985

By J. Skrove, C. R. Boardman

In situ permeability of the rock outside the Hardhat chimney was determined by pressurization of long holes with air. Experimental data indicated a remarkable difference between fracture permeability of the rock near the chimney and that at a considerable distance. Although permeable fault zones were known to exist in the granite stock, the measurements of background permeability were quite low, on the order of tenths to several millidarcies. The observed difference is about two or three orders of magnitude above this background in the region 125 to 215 ft radially from the shot point, or 80 to 165 ft radially from the vertical axis of the chimney. The presence of a collapsed drift immediately beyond this region precluded measurements which could have defined the maximum extent of the zone of high permeabilily. INTRODUCTION Previous exploration has revealed that contained nu-clear explosions create cavities which generally collapse, resulting in rubble-filled chimneys and annular fractured zones. These geometries have been shown to result in complex flow regimes which should increase the production rate from hydrocarbon reservoirs.' Empirical scaling equations have been developed for estimatina chimney radii and heights for a variet; of rock media.' The exten; of the annular fractured zone has been documented and associated permeability changes have been observed qualitatively for several explosions. This study was begun to establish the nature and magnitude of the permeability of the latter region. It is anticipated that results will be useful in estimating permeability changes and consequent production stimulation which might ensue from a contained explosion in a hydrocarbon reservoir. The post-shot environment of the Hardhat event (a 5-kt contained nuclear explosion in granitic rock) was c'hosen for the experimental measurements. The Hardhat device was detonated at a depth of 939 ft, and subsequent exploration revealed a chimney of broken rock with a radius of 65 to 70 ft and a height above shot point of 281 ft.' BeFore the explosion, the Hardhat medium was highly jointed and fractured (Fig. I). Jt was expected that differential rock motion along these and other weaknesses induced during cavity growth and collapse would significantly alter the permeability of the rock mass. EXPERIMENTAL METHOD Initially, three 2-in. diameter holes (Nos. 10, 12 and 19) were drilled about 25 ft outward through the walls of the 500-ft level drift (elevation 4,253 ft, Fig. 2). One was drilled near the chimney and two holes, one vertical and the other horizontal, were drilled near the shaft. Order-of-magnitude differences in permeability obtained by pressurization measurements indicated further: investigation was warranted. A series of 3-in. diameter holes was then drilled with water as a coolant into the walls and roof of the drift (Fig. 2). An 11-in. long packer was set from 1 to 8 Et inside each hole and air was injected at measured Row rates. Hole pressures were monitored at the collar. Permeability was low enough in the holes near the access shaft that pressure could be maintained long enough to obtain good pressure decay rates. In the vicinity of the chimney, however, permeability was so high that this was not possible and air was injected under steady-state conditions. About one year later, these same holes were retested to

Jan 1, 1967

By C. H. G. Bushell, M. Malnarich

Reagent control in flotation is more an art than a science. Operators vary the amount of re- agents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercorrection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment.

Jul 1, 1956

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By C. E. Reinhard

A USEFUL accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the, merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols.

Jan 1, 1929

By Joseph Bernhardt

Use of concrete underground at No. 4 mine, Cornwall, Pa., has become increasingly important. Starting with small amounts at finger openings, occasional raises, piers, its use has expanded to entire slushing drifts and haulages. Besides eliminating costly timber repairs, concreting costs of slushing drifts have proved cheaper than timbering. Higher haulage-concreting costs are offset by no maintenance charges during the life of the haulage.

Jan 3, 1950

By John S. Alexander

THE spirit of this age encourages the substitution of mechanical for hand labor wherever possible, experience proving that the employer, employer and consumer share alike in the resulting benefits. Through the efforts of the inventor, millions of the laboring class have been raised from being mere contributors of muscular force to be brain workers and directors of those ingenious contrivances now so widely used in the various branches of agriculture, manufacturing, printing, etc. While the genius of invention has accomplished so much in other departments, it seems remarkable that she has not long ere this descended into the coal mine with her wheels, levers, and eccentrics, and provided the toilers there with some device by which their unusually laborious work could be lessened. Until within a very few years, however, little special attention was given to this subject, owing largely, no doubt, to the fact that coal miners as a class were prejudiced against innovations of this kind and ignorantly clung to muscle as the only means of wresting from nature her treasures stored within the coal measures. Thanks, however, to the enterprise and skill of some Scotch and English mine proprietors and inventors, the present decade has seen rapid strides in the right direction, and mechanical coal mining has become a fixed fact in some portions of Great Britain. Making her acknowledgments to the mother country for these earnest and successful efforts, America now comes forward with the Monitor Coal-Cutter as the result of a trial on her part to advance the common cause of economical coal production; for upon cheap fuel the future greatness of both nations largely depends. The object of this paper is to give a few items in regard to this Monitor Coal-Cutter, which, so far as the writer is informed, is the

Jan 1, 1875

By Donald B. Gillies

THE great source of iron ore for the furnaces of this country has been the Lake Superior district. Ore was first discovered there in 1844, and the first shipments made via the Great Lakes in 1852 to a furnace at New Castle, Pa. The stream of ore from that region increased slowly to exceed a million tons in 1873, and did not reach 10 million tons until 1895. By 1901 it exceeded 20 million tons, and in 1907 over 40 million tons. Total Lake Superior output through 1948 was about 2500 million long tons. Outside the Lake Superior district are the Southern district, including mainly Alabama, Georgia, Missouri, and Texas; the Eastern district of New York, New Jersey, and Pennsylvania; the Western district embracing Wyoming, Utah, and California.

Jan 1, 1949

By B. Barlin, G. A. L. Smith, I. J. I. Delaney

A method was developed to quantify the three mineral species, sphalerite, galena, and pyrite in seven concentrator products. Intermineral effects were studied and a statistical analysis was undertaken to assess the accuracy and reproducibility of the method. The method is both rapid and suitable for plant control purposes. Furthermore, it requires only semiskilled laboratory personnel to carry out all the analyses.

Jan 1, 1976

Jan 1, 1969

By C. E. Mendenhall

THE word temperature has both a colloquial and a technical use. For everyday purposes of abusing the weather man, no very exact definition is necessary, but for the purpose of giving a simple summary of the physical laws that form the basis of practical pyrometry, something more precise is required. Beginning, therefore, with the common concept of "hotness" and "coldness," we must agree on a method of measuring differences in "hotness," on the unit to be used, and on the point from which measurements are to be taken. We shall then have a definite "scale of temperature," which can be used in all methods of pyrometry. But, as in many similar cases, it is much easier to define or describe something than it is to make practical application and use of the definition; so that much of our attention will be taken up with practical methods of realizing or applying the scale agreed upon. It was early observed that changes in temperature produced large and easily measurable changes in gases, which may be most simply separated into changes in volume (expansion and contraction) under conditions of constant pressure, and changes in pressure under conditions of constant volume. These changes are much the same in magnitude for the common gases oxygen, nitrogen, and hydrogen and also for the rarer helium and argon. This relative uniformity in behavior led to the suggestion of "the gas thermometer" and "the gas scale" as the basis for all temperature measurements. However, as methods were refined, differences appeared between different gases and different ways of using gases, so that Lord Kelvin introduced his more fundamental notion of the "absolute thermodynamic scale" of temperature, which he defined as follows: Given two bodies, say two tanks of water, at different temperatures to determine these temperatures on the "absolute thermodynamic," or Kelvin, scale, operate a thermal engine between these two temperatures, letting it take in heat from the hot body and give out heat to the cold, which therefore corresponds to the boiler and the condenser of a steam engine. The engine we may imagine as a cylinder and piston inclosing a gas and operating with the well-known Carnot or isothermal-

Jan 9, 1919

By V. N. Mackiw, D. E. Weir, D. J. I. Evans

The world's largest reserves of nickel are found in lateritic ores. Commercial exploitation has been carried out for almost one hundred years; however, none of the plants currently in operation produce pure nickel but rather ferronickel, matte, impure nickel oxide or mixed sulphide precipitate. Over the past decade Sherritt has studied various processes, including the modified reduction roast-ammonia-ammonium carbonate leach process, for the production of pure nickel powder and briquettes from laterites. Nickel can be reduced to the pure elemental form at elevated temperatures and pressures from impure basic nickel carbonate slurries. Several methods were studied in the development of the process for working up the pregnant leach liquor and basic nickel carbonate to produce feed for the aqueous hydrogen reduction step in which pure nickel powder is produced. This paper is concerned only with the laboratory studies using the basic nickel carbonate slurry reduction procedures.

Jan 1, 1973

By J. A. M. van Liempt

Since the discovery of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state Method A 1. Tamwmnn's Method1—Tammann succeeded in making bismuth single crystals of a maximum length of 20 cm. by undercooling the molten metal 0.1 to 0.3' G. below its melting point in glass tubes of a maximum