Search Documents

By W. V. Youdelis, W. H. Bear, G. Cochrane

HERETOFORE, there has been very little study of the effects of various metallurgical factors on the behavior of thermoelectric materials, the need for which is evident if optimum processing and design of thermoelectric devices is to be realized. Accordingly, we have undertaken such an investigation on the thermoelectric materials bismuth and Bi-Sb alloy and in this paper present some preliminary results which merit consideration, in particular the relatively high thermoelectric power and figure of merit values obtained for the Bi-12Sb (at. pct) alloy powder compacts. The thermoelectric parameters for ingot and powder compact specimens are determined and the results are compared with published data for single crystals. Preparation of Materials. The bismuth and antimony used in this investigation are six nines pure. Melting and casting of the ingots was carried out in air for expediency, since most oxidation unavoidably occurs during the preparation of the powder by filing of the ingots. Chill cast ingots of pure bismuth were prepared by pouring the melt into split copper chill molds, and unidirectionally solidified ingots of bismuth and Bi-Sb alloy were obtained by slow directional cooling in pyrex tubes. All melts remained bright during melting and casting, indicating minimum oxidation. Powder for the powder compact samples was obtained by filing the ingots with a fine and coarse file to give a variation in the particle size of the compacts. The particles in the fine powder compacts varied in size from approximately 28 pct less than

Jan 1, 1970

By James E. Harding

The usual method of sampling mineral deposits is to drill holes and assay the sludge or core. Though the results thus obtained may not represent the true average value of the deposit, it is on these results that estimates of practically all large orebodies are made. In a large number of cases, the results of exploitation fall far short of the estimated value of the orebody. The standard method of making these estimates is to find the cubic contents of triangular prisms, in the apexes of which the drill holes are placed, by. multiplying the surface area by the average depth of the ore in the three drill holes and then multiplying the cubic contents by the specific gravity of the ore or rock to find the tonnage. The assay value is found by dividing the sum of the products of the depth of ore in each hole and the corresponding assay value by the sum of the depths of the ore in the three holes. As the latter part of this method is subject to many mathematical errors, it should not be depended on. Some engineers, therefore, use a discount factor, but as this factor is either arbitrarily selected or is obtained by obscure methods, the results are no better than guesswork. The standard method is correct when the drill holes are so laid out that the triangular prisms are equilateral in cross-section. But as ore deposits cannot always be drilled into at regular intervals and because of the human factor, if many holes are drilled, triangular prisms of all degrees of angularity are produced. In such cases it is necessary to assume that the influence of the different holes is not the same in all directions, which assumption of course is absurd. The area of the triangular prism is usually found by scaling; an ore-body of sufficient size to justify churn drilling is too large to be handled conveniently on maps having a scale larger than from 1000 to 1 to 1,500 to 1 and maps of such scales cannot be accurately measured. A variable is thus introduced in the first operation. In addition, the scaling is frequently done from blueprints, which sometimes shrink as much as 4 per cent. between printing, washing, and drying. The error due to scaling may be eliminated by surveying the location of each hole and

Jan 1, 1922

By A. H. Dierker

NEXT to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate, figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry.

Jan 1, 1929

By Marcel Daly

IN a preceding paper 1 the writer has pointed out some apparent relationship between the distribution, on the Surface of the globe, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth's body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the pre-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limestone) ; and the Beltian system of the same region contains layers of argillites and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons wider conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. They constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the differentt stages of evolution of the primitive, parent matter. . The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunninggam-Craig has recently shown how intimately shale fields and oil fields are connected. For this reason, no distinction is made in the present

Jan 8, 1917

Jan 1, 1918

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1,1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company's Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956

By Sheldon P. Wimpfen, Nelson Severinghaus

13.2-1. Introduction. Man's first association with industrial minerals came at the dawn of history when a remote ancestor first put a few rocks together to protect a fire or selected colored clays to decorate his face. He was dealing with industrial minerals when he selected flint to tip his arrows or scrape a hide. From that inauspicious beginning shrouded in the mists of man's earliest history, industrial minerals have grown tremendously in importance to our civilization. The growth rate of the industrial minerals, or nonmetallic group, has been considerably greater than that of the metals group, as can be seen by the following Fig. 13.2-1: [ ] Industrial minerals produced in the five-year period of 1961-1965 had more than twice the dollar value of the metals produced:

Jan 1, 1968

By Nicholas J. Grant, Gordon D. Gemmell

CREEP rupture characteristics of high purity Al-Mg solid solution alloys were studied by Mul-lendore and Grant' to investigate solid solution strengthening of pure aluminum and the accompany- ing effects on deformation and fracture characteristics. This paper presents the results of an extension of that work to A1-Cu and Al-Zn alloys to permit a comparison of the relative effects of the three solute elements on the high temperature strength and on the deformation and fracture characteristics. Experimental Procedure A total of nine alloys was studied. They were all made of ultra high purity aluminum alloyed with high purity copper, zinc and magnesium. The corn-

Jan 1, 1958

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

Until recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, preheating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about II50 C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the front of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29,1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942) and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August 1942 under contract with the War Production Board and under the supervision of the War Metallurgy Committee. This paper describes the ,phases of the investigation that are thought to be of sufficient general interest to merit publication.

Jan 1, 1944

By Robert N. Eli

The application of Geographic Information System (GIS) technology to support the planning, design and analysis of coal mines is discussed. Traditional two-dimensional GIS structures are modified to produce a three- dimensional GIS system that combines the efficient topologic description of a cubic grid cell skeletal structure with the precision surface representation of a Triangulated Irregular Network (TIN). The surface terrain and any subsurface strata, such as a coal seam, are represented by separate TIN'S. Any attribute data to be assigned to the TIN'S are stored in polygon overlays. Any remaining spatial data are stored as link strings or nodes in a global data set. The most valuable application of the system is the production of map products. Both projections and cross-sections of surface or subsurface structures are possible, in either horizontal or vertical planes. Engineering data, including lengths, areas, or volumes, can be calculated.

Jan 1, 1983

By C. D. Michaelson

The memory of D. C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was immeasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War II, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling's remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential.

Jan 4, 1969

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." ' Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an almost identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds." 2 Vn the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter. Sources of fatty acids which may be used as collectors are legion, but provided the oleic acid content is high enough, cost is normally the determining factor. Usually this restricts severely the purity of the collector in terms of its oleic acid content. Within the past year or so users of crude oleic acid have become somewhat more discriminating, apparently realizing that some of the organic acid impurities may exert deleterious effects upon certain separations. Marine fish oils have been used as collecting agents, particularly in the earlier days of froth flotation. Currently their use is restricted in this field to relatively minor applications, although they are cheap sources of fatty acids. In an effort to increase the range of uses for fish oils, the U. S. Fish and Wildlife Service has awarded contracts to study these materials as sources of new products suitable for commercial development. Funds for these investigations were provided by the Saltonstall-Ken-nedy Act of 1954. One such contract was awarded to the University of Minnesota School of Mines and Metallurgy for the purpose of investigating the use of fish oil fatty acids and their derivatives in ore flotation. Besides the esters of various saturated aliphatic acids and of palmitoleic and oleic acids, fish oil also contains esters of monoethenoid and polyethenoid acids with 20, 22, and 2 carbon atoms. The basic purpose of the investigation was to determine whether the longer-chained unsaturated acids possess collective properties superior to those of the C,, monoethenoid oleic acid, the C16 monoethenoid palmitoleic acid, or the saturated C,, stearic acid and its shorter chain homologues; whether highly unsaturated acids have merit as collectors; whether rela-

Jan 1, 1960

By S. R. Gilbert, B. W. Burdett, L. B. Hales

A brief review of grinding control systems is given with a review of the most popularly reported control loops. The trend toward more sophisticated control systems in terms of control strategies and control equipment is discussed, and the reasons for the popularity of distributed control equipment are outlined. The evolution of the interface between the operator and the process and its importance in plant control is described. Finally, the authors' view is given as to the future of grinding control.

Jan 1, 1984

By G. S. Hume

IN THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baume in a sand 17 ft. thick in its No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed' and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported . to have been encountered below the producing gas horizon, in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The 'structure underlying this portion of the plains was supposed to-be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and it is in these folds that the oil land gas are found. At the British Petroleums Nos. 2-and- 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in 1/2 mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2-and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers', Fincham and Richardson,la by St Pierre and Chipman,' and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

By Arthur W. Rose

Statistical techniques are being widely used in geochemical exploration to answer questions involving sample spacing, analytical and sampling errors, thresholds, data smoothing, and optimum combination of several elements into one measure of favorability. The applications of sampling theory, mean and standard deviation, trend surfaces, moving averages, factor analysis, cluster analysis, discriminant analysis, and regression analysis to these questions are discussed with examples. Although the techniques are very useful as means of handling large amounts of data, they require as much geological and geochemical judgment as any other approach to data interpretation.

Jan 1, 1973

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968