Search Documents

By A. J. Weinig

THE Liberty Bell cyanide precipitate is unique in that it is apt to vary widely in composition in the course of very short, periods of time, and a method of refining and melting that would prove highly satisfactory at one cleanup would yield almost an hopeless "mess" it a second. Table I gives a general conception of the wide range in grade and composition of those raw precipitates. It is evident that no one standard flux could be expected to produce a high-grade bullion with such a widely variable precipitate, and that any method of treatment with acid requires most careful consideration. Refining by Acids Naturally, our first efforts to improve our precipitates were directed along the lines of acid treatment. Table II embodies the results of careful sampling and analysis of one cleanup at the time when wet refining reached its maximum development at this mill. We have now discarded all methods of wet refining, successfully replacing them by amore scientific method of flux calculation described herein, but it is believed that a general description of this wet refining is warranted as it throws some interesting side lights on acid refining in general.

Jan 3, 1916

By Ronald J. Roman

Research pertaining to flow of solutions in leach dumps has generally been neglected. This technical note proposes a method for evaluating the flow patterns and incorporating the results into dump-leaching models. Three dump-leaching models1-3 have been proposed to scale up laboratory test data to expected field results. These models are based on the same physical picture in a dump and differ only in the importance of diffusion or surface chemical reaction rate. Selection of this rate-controlling phenomemon is based on type of ore (sulfide or oxide), physical dimensions of the particles being leached, and the leach heap itself. All three models are applicable to specific types of operations. The models are similar in the use of a size distribution analysis for the dump material and the assumption that the leach solution flows around each particle. Transport of the leaching agent to the interior of the particle takes place by diffusion [(Fig. 1)]. However, normal dumps are of a higher bulk density than the material in a laboratory column used to generate the scale up data. How does this difference in bulk density affect the scale up equations? Increasing the bulk density can be expected to give more particle-to-particle contact; therefore, individual particles will be blinded by each other. As blinding increases with bulk density increase, the particles will behave like larger particles with a coarser apparent size distribution. The extreme will occur when the bulk density reaches that of the undisturbed rock, the entire dump behaving as a single particle with the dimensions of the heap itself. Harris4 alluded to this phenomenon in his paper. An alternative method of describing the same phenomemon is to consider the flow paths of the solution. At high bulk densities leach solution no longer surrounds each particle, but flow paths are separated by several particles and channeling is said to take place. Instead of the particle radius being the maximum distance through which the leaching agent must diffuse, the maximum distance is half the separation distance of the solution flow path. Particle size distribution must then be replaced in the models by the concept of channel separation distribution. Like size distribution, channel separation distribution specifies the cumulative percentage of the rock in the dump situated less than a specified distance from a solution channel. Thus, [ ] Distribution of the solution channels is a function of how the dump was built (among other things), and therefore it cannot be determined in the laboratory. Accordingly, it becomes necessary to determine a range for d and a in existing operations or measuring these parameters before leaching starts. Howard5 gives a clue to one possible technique of measuring solution channel distributions. When his paper was published little was known about the phenomemon of leaching; the importance of this type of data was not recognized. [Fig. 2] is a Y-Y log for one hole drilled

Jan 1, 1978

By Arthur S. Coffinberry, Ralph Hultgren

WE have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, combined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atoms, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electronto-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such information is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By C. Dinis da Gama

In mining, all unit operations are closely interrelated, and the results of blasting are probably the key factor within that sequence. The drilling program prior to blasting is just as dependent upon the desired rock fragmentation as are the loading, hauling, and mechanical crushing operations which are economically and technically influenced by the results of blasting, namely, the size and scatter of the product. What is known today as optimum blasting is the process of designing a blast in order to obtain a certain degree of fragmentation so that overall mining costs are minimized. Applying this criterion often results in a different program than when an individual blasting pattern is chosen only on the basis of the lowest operational cost for that pattern, disregarding what comes before or after the blast. [Fig. 1] shows the characteristic variation of mining unit costs with the degree of fragmentation, or the maximum size of blocks obtained from blasting. From the figure, it can be seen that optimum breakage must correspond to the lowest total costs, but reducing drilling-blasting costs only does not achieve such an optimum solution. Methods of designing surface or underground blasting operations should comply with the optimization criterion, but this compliance is feasible only if a detailed mining system analysis is available. Therefore, predictions of costs of loading, transporting, and mechanical breakage of ore as a function of its size will define a narrow range of variation for drilling and blasting parameters in order to get the minimum total costs.

Jan 1, 1972

By Jim V. Rouse

In situ mining and dump leaching has been practiced for years. Recent environmental concern over conventional mining and milling techniques has rendered in situ mining more attractive. While there are many environmental advantages to in situ mining, there are disadvantages which, if ignored, can lead to environmental damages, followed by stringent control. The environmental advantages and disadvantages of the various types of in situ mining operations are discussed. Current legislation and regulations governing in situ mining are cited, together with a suggested program of environmental monitoring designed to protect the mining company as well as the environment. Suggestions are made for possible solution of existing pollution problems associated with previous mining activities by heap-leaching techniques. Present and indicated control of subsurface injection is traced, because of the many similarities in philosphy and monitoring requirements to in situ mining.

Jan 1, 1974

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.'-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

By William J. Potter, Roger N. Pyle

Introduction The primary ingredient for survival of mining companies during a recessionary period is to be innovative and resourceful in the structuring and financing of operations. Over the past decade, many mining companies have had to retrench and restructure their operations and to redeploy their assets just to survive. During the same period, traditional sources of financing for mining companies -- commercial banks, subsidized export credit loans and long term straight debt financing in the public markets -- became less available and more expensive. Meanwhile, new markets and new financing instruments provided new alternatives for mining companies. Those companies which exploited these alternatives greatly enhanced their capacity for survival and even for profitability. This article considers the strategies adopted by some companies to adapt to changes in this recessionary environment; the inadequacy of traditional sources of financing; certain of the new financing instruments, structures and markets which have become available; and how several mining companies have utilized these new instruments, structures and financial markets to improve their competitive positions. THE IMPACT OF RECESSION ON MINING COMPANIES AND TRADITIONAL FINANCING SOURCES In its 1983 year-end article "The New Economic Order" Mining Journal characterized many of the large private sector mining companies with operations in the industrialized countries as being "gripped between the jaws of high working costs and stagnating metal commodity prices." The article went on to characterize the Canadian mining industry in particular as being "in the difficult position of having to seek to sell the bulk of its output in a world market characterized by over-capacity, where production costs were determined by internal political and economic factors while prices were set by external competitive forces of supply and demand." Miners of a wide range of commodities in the industrialized countries have come to realize that their domestic mineral resources are in many cases no longer competitive with global sources of supply. To compete and survive they would have to rely on their technical and financial expertise in mineral exploration and development and in mining and processing. Strategies For Survival Global competition has compelled management in the extractive industries to improve their worldwide cost position. This is the only means whereby a mining company can differentiate its product and attain a substantial competitive advantage. During the past decade, for example, ASARCO Inc. and Inco Ltd. chopped their payrolls, postponed expansion plans and otherwise retrenched. ASARCO reduced its capital expenditures and cash requirements for operations in 1984 to a level almost equal to its internally generated cash. The company's finances were also strengthened by increasing total lines of credit from outside sources, by selling common stock, and by reducing annual pension funding through a change in actuarial assumptions. Other companies returned to their traditional organizational structure where they had a demonstrated competitive strength. Consolidated Gold Fields, for instance, resumed its operation as a mining finance house. Its capital investment programs are now devoted solely to resource development. In mid-1984, at a time of firming zinc prices, Union Miniere S.A. used the opportunity to integrate its smelting capacity and to direct investment to certain subsidiaries at the expense of less viable operations. Smaller corporations realized that it was not enough just to be the low-cost producer. For example, Drummond Coal Company in Alabama, which dominates its regional market due to its low-costs, has also developed a world-wide trading capability and has placed incremental tonnage from its own mines as well as brokered coal produced by others, thereby minimizing capital risk. In Canada, Campbell Resources has exploited difficult times by acquiring assets cheaply. In the process it improved its capacity to withstand cyclical economic swings by diversifying from solely a copper and gold producer to a company based upon asbestos, coal, copper, gold and natural gas.

Jan 1, 1985

By Samuel Wyer

Over 8,000,000 people in the United States depend on natural gas for their cooking, heating and lighting service. This service has been made possible only by the investment of large amounts of capital in transportation lines connecting the gas wells to the various communities, thus combining a hazardous mining operation with a public utility service. The effect that making these lines " common carriers" will have on the present and future service to these 8,000,000 or more people is of far reaching ethical and economic importance, and deserves careful consideration. As an introduction, it must be conceded that: 1. Natural gas, although a mineral and obtained by a mining operation-with more uncontrollable and uncertain features to cope with than exist in the mining of coal or other minerals-when served to the public becomes a public utility service. 2. The governmental power to regulate all public utilities in the interests of the public cannot be successfully disputed. 3. Mere suggestion of inconvenience to the utility is wholly irrelevant, as it cannot be considered or allowed to influence in making a defense against governmental regulation. Unfortunately it is not generally appreciated that: 1. Legislative enactments are not necessarily laws, and cannot abrogate economic laws or alter engineering facts. 2. There is a clear distinction between "common carrier" and "public utility," although the terms are frequently confused. ' "A common carrier is one who undertakes for hire to transport persons or goods, or both, from place to place for all persons indifferently, the term implying indifference as to whom shall be served, and an equal readiness to serve all who apply, in the order of their application." On the other hand, property becomes a "public utility" only "when for a particular purpose the public have a right to resort to the premises and make use of them."

Jan 5, 1914

By John V. Beall

On the banks of Huzzah Creek there is a roadhouse where a group of Ozark folks were whiling away a Sunday afternoon last spring. "How about some of that 'Who Broke the Lock Off the Hen House Door,' " suggested Spinny. The old man obligingly picked up the fiddle and began the sprightly tune. His long, seamed face had ruddy cheeks and a grey stubble jaw. A thick fedora was pushed back off his scraggly hair and he wore a heavy jacket. It was 73 degrees fetchin up for 75 on that May afternoon, so naturally he sweated. The Ozark is fiddling country. The natives, to whom a half dollar looks as big as a manhole cover, put great store by fiddling, along with the other fine things of life such as fishing and horse raising. On the wooded hills, 1200 to 1700 ft above sea level, there are numerous tumbling streams with plump fish, and in clearings along the roller coaster roads are long-legged, frisky looking horses. People in the Ozarks have a reputation for self-reliance. However, they are cheery and friendly to strangers. Trespassers are very seldom shot at-except if they do something wrong or by accident.

Jan 7, 1963

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

This paper presents details of the concept that size reduction in comminution machines takes place by three mechanisms; namely impact, abrasion, and chipping grinding. Experimental evidence is presented to show that each of these comminution mechanisms produces particles of a characteristic size distribution. The actual product from a comminution device has been postulated to be the result of a composite of these three types of mechanisms. Composite curves are demonstrated for a material following the Gaudin-Schuhmann, Gaudin-Meloy, and Rosin-Rammler size distributions. About forty years ago, Gaudin1 showed that grinding may be considered a combination of impact and attrition. Since that time, major efforts have been devoted to studies, both experimental and theoretical, of impact and compression fracture, while attrition has been almost wholly neglected, at least quantitatively. A significant attempt to distinguish between attrition and impact grinding is the work of Tanaka2 in Japan. By means of an instrumented abrasion grinder and a drop weight device, he determined coefficients relating the increase in surface area of various materials to the energy expended by the two methods of comminution. He showed that physical properties of a material determine its response to attrition and impact grinding. By extending his ideas to ball milling, he concluded that to a large extent the basic comminution process in a ball mill is due to the impact of falling media. Because Tanaka used a mass of particles in his drop weight device, however, he did not obtain pure impact size reduction. The purpose of this paper is to define basic mechanisms of size reduction, to verify that each has a characteristic and meaningful distribution curve, and to show how a combination of these mechanisms results in a size distribution very like that produced by grinding mills. DEFINITION OF COMMINUTION MECHANISMS The product from a grinding device will be considered to be the sum of the contributions resulting from the action of three basic mechanisms of size reduction which operate in a ball and rod mill. These are impact grinding and two forms of attrition, namely abrasion grinding and chipping grinding. Each is defined below. Impact Grinding: If a straight line is obtained when the cumulative weight fraction finer than a given size is plotted on log-log paper as a function of that size, the slope of the line is defined as the distribution modulus. A number of investigators 3,4,5 have shown that impact fracture of single specimens of different composition and shape results in a distribution of daughter particles that exhibit a distribution modulus of unity. This has also been true for materials broken in slow compression. Moreover, under slow compression or impact fracture conditions, theoretical distribution equations6*' which approximate the Gaudin-Schuhmann distribution when the distribution modulus is close to unity agree reasonably well with the experimentally obtained products. If one now considers a comminution process where many impact or compression fracture events are taking place, then any rational summation of the individual events yields, in the finer size range, a Gaudin-Schuhmann distribution whose distribution modulus is also unity. If the size distribution of the product from a mill has a distribution modulus of unity, it is implied that particles are fractured in a manner which results in a comminution event having a distribution like that obtained for the breakage of single specimens. These impact events would occur when a particle is smashed between balls or between a ball and the mill liner. Attrition, on the other hand, is that form of grinding which cannot be called impact grinding, and comprises both abrasion and chipping grinding. Abrasion Grinding: Abrasion is a form of surface wear resulting when particles rub against each other or against balls or the mill liner of a tumbling mill, somewhat like a piece of wood being rubbed over a piece of sandpaper. The surface wears at a more or

Jan 1, 1964

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 114 to 112 in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles.

Jan 8, 1960

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,' and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3'4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.' All material used was guaranteed by the supplier

Jan 1, 1968

By James E. York

At a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr. C. B. Dudley, in his presiden-tial address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective requiremeuts of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical authorities lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the finished product. Chemical knowledge in steel-making is far ill advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

Jan 1, 1910

By D. M. Deason, R. M. Chhatre, G. Y. Onoda

INTRODUCTION The treatment of colloidal suspensions is a subject of increasing interest in mining and benefication (1). Colloidal suspensions are not readily operated upon by mechanical and physical methods useful with coarse suspensions, such as filtration, thickening, and flotation. This is because colloids are strongly affected by interfacial and interparticle forces that may be large compared with, and resistant to, external forces. The degree and type of interactions between colloids can be modified by small additions of reagents such as coagulants, flocculants, dispersants, and immiscible liquids. These alterations in turn change the properties of the suspension and provide possible opportunities for transforming suspensions to a more favorable condition for a given processing operation. Phosphate slimes are an example of a colloidal system of interest today. In the mining and beneficiation of phosphate rock in Florida, slimes are a waste product. The phosphate ore (called matrix in the industry) is slurrified hydraulically and pumped to a beneficiation plant, where the -150 mesh material is removed by cycloning from the coarser phosphate rock and silica. The resulting -150 mesh slurry, called phosphate slime, is pumped to large impoundments. The solid content of the slime entering the impoundment is around four weight percent, and over 80% of the solids is less than one micron in size. The immediate problems with phosphate slime relate to their disposal (2, 3). The disposal problem is associated with the very large volumes and the poor dewatering characteristics of the slimes. To have sufficient impoundment volume, large earthen dams are built around the mined areas. The volume above ground level approaches and

Jan 1, 1980

By Charles Kirchhoff

For twenty years it has been my work to watch and record progress in both the technical and the commercial branches of mining engineering in the wide sense in which it is represented by our Institute. While you who have been actively engaged in our profession have made history, a few of us have attempted to be the historians and have been kept keenly on the qui vive to follow the developments of so broad a field. One so employed may be pardoned if he ask you to pause for the unusual purpose of looking backward, that you may measure what you and others have done, and that the younger men may gather inspiration from the work accomplished by their elders and their predecessors. It is not so long since that the commercial management dominated our industries. Bred in the school of science, which seeks its reward in establishing the truth, our engineers were sometimes indifferent to trade conditions and requirements. Much of that feeling has disappeared, and the engineer recognizes that it is his mission to apply the achievements of science to a useful commercial end. On the other hand, business men now understand that the utilization of our natural resources and the production of articles for consumption is impossible without the intervention of the engineer. They must co-operate, unless, indeed, the two functions are combined in one man —a rare but powerful combination. Now the final measure of success of both is the cost sheet on the one hand and the expansion of markets on the other, so closely interwoven, so mutually interdependent. There is one cardinal feature, however, which characterizes the engineer's work—namely, the permanence of his achievements. Every improvement, particularly when it has been recorded in such lasting form as a paper in the Transactions of our societies—

Jan 1, 1900

By G. H. Matheson, J. M. W. Mackenzie

The coal concentrates studied contained clay slimes which would not flocculate on the addition of a polymer flocculent alone. The mechanism of the flocculation process is interpreted on the basis of the flocculation of lyophobic colloids. The filtration rate characteristics are shown to deviate slightly from certain basic filtration equations. Cake moisture was shown to decrease with cake drying time and vacuum, and increase with cake thickness. Filtration is a commonly accepted method of dewa-tering the fine coal concentrates produced in coal cleaning operations. Dewatering of these concentrates, using drum or disc vacuum filters, usually presents few technical difficulties and will result in the production of a filter cake containing some 20 to 25 pct moisture. In many coal cleaning operations it is common practice to add flocculants to the coal concentrates prior to filtration to increase the filtration rate. The mechanism whereby flocculation increases filtration rate has been summarized by Gaudin,4 while Geer, et a15 have compared the effectiveness of starch and synthetic flocculants as filter aids for a variety of coal concentrates. Coal concentrates, containing appreciable quantities of expanding lattice clays of the montmorillonite-illite group, sometimes prove impossible to filter without flocculation of the pulp prior to filtration. The fine coal concentrates produced at the Newcastle washery of The Broken Hill Proprietary Co. Ltd. fall into this group. Coals mined in this district contain appreciable quantities of expanding lattice clays which break down in the washery circuit waters and, by processes of mechanical inclusion, contaminate the coal concentrate thickener feed. Despite the classifying action of this thickener, the underflow which is pumped to the filters contains sufficient clay slimes to render filtration of the unflocculated pulp impossible. Filtration leaf and plant tests were carried out to develop effective and economic flocculant combinations and to determine the filtration characteristics of the flocculated coal concentrates. The determination, by leaf testing, of the filtration characteristics, and the analysis of these characteristics in the light of the equations of Brown2 resulted in the successful trial operation of the filters in the Newcastle washq. Although the filtration characteristics are not entirely in agreement with the theoretical treatment of Brown, the equations developed made it possible to predict, from leaf tests, the effect in the plant filters of pulp density, form vacuum, and form time on filtration rate and filtrate volume. EXPERIMENTAL PROCEDURES The sample used for leaf testing was the coal concentrate thickener underflow, which in plant operations would form the feed to the two 12-disk Dorr-Oliver filters. The feed to the coal concentrate thickener comprises the undersize produced by dewatering the Diester table concentrate on 5-mm dewatering screens and the overflow produced by cycloning of the froth flotation concentrate. At the time of testing these filters were inoperative because of the difficulties in filtration, arising from contamination of the

Jan 1, 1962

By S. R. Krom

In connection with perfecting a system of pneumatic concentration I had in view the improvement of machines for crushing and pulverizing ores. A study of the whole subject convinced me that the principle upon which the construction of the Blake crusher, and that of rolls, is based, possessed the mechanical elements which, if perfected and simplified, would make these machines the successful rivals of every other device. It is well-known that until very recently the stamp-battery held undisputed possession of the field; and mill-men and mill-builders almost universally believed that stamps would not be superseded by any other machine for fine crushing. The first step to drive stamps from the field was the introduction of rollers in the Bertrand and the Mt. Cory mills. In both of these mills the great superiority and economy of a system of crushing with rollers instead of stamps has been fully demonstrated. While perfecting the rollers, I had the fact confronting me that they had frequently been tried without success. In fact, the universal opinion prevailed that rollers could be used only for coarse, and not for fine crushing. The secret of the difficulty I discovered to lie in the imperfect and weak character of the rolls heretofore used, due to a misconception of the requirements for a machine for such work, and a failure to appreciate the advantages of continuous, rolling, crshing- surfaces, operating on the toggle-lever principle, which gives the greatest crushing pressure with the least power. expended, and the minimum of wear.

Jan 1, 1886

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.' Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer's3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965