Search Documents

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By Stanley M. Miller

For rock or soil materials assumed to be generally isotropic and homogeneous, seepage theory and analytic geometry can be used to develop a mathematical technique for estimating the steady state, pie-zometric drawdown to a slope face. The resulting parabolic drawdown curve is a function of slope angle and the height of the original water table above the slope toe. When the slope is cut at a rate faster than that which allows a steady state to be attained, a non- steady state analysis approximates the transient drawdown. Monte Carlo simulation provides realizations of possible drawdown curves that can be included in slope stability risk analyses.

Jan 1, 1983

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

By P. D. I. Honeyman

CHANGING trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1932

By Willis H. Carrier

Particular interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world&apos;s deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly newl-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104" at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1940

By Willis H. Carrier

Particular interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world&apos;s deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly newl-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104" at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1940

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of October, 1913: Members. BARNES, KENNETT F., Secty Granby Min. & Smelting Co., St. Louis, Mo. BILLINGSLEY, PAUL, Geol 526 Hennessy Bldg., Butte, Mont. BLANCHORD, RALPH C., Geol 3 Lombard St., London, England. BOYLE, ALBERT C., Jr., Prof. of Min. and Met., University of Wyoming, Laramie, Wyo. BRADFORD, JULIUS S., Min. Engr Chiksan Mining Co., Chiksan, Korea: CLEMES, ALFRED W., Min. Engr P. 0. Box 6,88, Moronic, Ariz. COPELAND, DURWARD, Met Cia. Estamifera de Llallagua, Bolivia, So. America. CRAWFORD, JOHN, JR., Mgr Noble Elec. Steel Co., Heroult, Shasta Co., Cal.

Jan 11, 1913

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through &apos;a No. 4 riddle. It

Jan 1, 1921

By Nicholas J. Grant, Ulf Kalling, John Chipman

THE operation of a blast furnace is dependent to an important extent upon the sulphur content of materials charged and the desired limit of sulphur in the product. It has long been known that the blast furnace is the most efficient tool for desulphurization in common use and that this efficiency is associated with the strongly reducing conditions of the hearth and is enhanced by increased basicity and fluidity of the slag. The chemical reactions of desulphurization may be studied from the viewpoint of the ratio of the process or of the final equilibrium conditions. Both kinds of studies contribute to an understanding of the process and both are included here. A simple measure of the desulphurization power of a slag is given by the ratio: Pct sulphur in slag (Pet S) Pct sulphur in metal [Pct S] This ratio was used by Holbrook and Joseph&apos;,&apos; to measure relative desulphurizing powers under controlled laboratory conditions. It was also used by Hatch and Chipman3 as a measure of the equilibrium distribution. For the latter purpose it would be preferable to employ thermodynamic activities rather than percentages, but until very recently this has been impossible for lack of data. Now, thanks to the work of Morris and Williams and Morris and Buehl," the effects of carbon and silicon upon the activity of sulphur in the metal are known. The confirmation of this work and its extension to include the effects of other elements by Sherman and Chipman and by Rosenqvist and Cox&apos; make it possible to calculate the activity of sulphur in pig iron of any composition. Hence it is now possible to use data on the equilibrium distribution of sulphur to find its activity in the liquid slag and to approach an ultimate solution of the thermodynamic aspects of the problem. The rate of transfer of sulphur from metal to slag is the problem of major industrial importance and indeed the principal need for equilibrium data has been as a necessary adjunct to the kinetic studies. The rate of approach to equilibrium under laboratory conditions seems slow compared to the requirements of industrial practice, and it is clear that further laboratory studies of rates are needed. In the research reported below, the items which were investigated were the following: I—The role of mechanical stirring on the approach to equilibrium. 2—The role of MgO in desulphurization as compared to CaO. 3—The role of MnO in desulphurization. 4— The limiting reactions which constitute the slow steps in desulphurization. Experimental Procedure The experimental set-up and procedure previously described by Hatch and Chipman" were essentially followed with several small modifications. The graphite crucible containing the slag and metal charge was altered to provide considerably more active stirring and mixing of the slag and metal in the carbon monoxide atmosphere. For this purpose the crucible was machined to provide two deep cylindrical wells which were interconnected at top and bottom as shown in Fig. 1. A graphite screw with a flat thread and of shallow pitch (4 threads per in.) spinning at 600 to 800 rpm was used to lift the slag and metal over the partition between the two wells and throw them over into the second well, where the metal settled through the slag into the reservoir at the bottom. It was possible to see actual particles of slag and metal being thrown over the partition. In this respect, the stirring was more vigorous than used in the work of Hatch and Chipman. A charge of 400 g of wash metal was first melted, and 20 g of FeS was then added to yield a bath containing 1.65 pct S. Immediately 400 g of slag (as pure mixed oxides) was added and fused. The slag was generally fused in 1 hr * 10 min. Within 30 to 45 min after melting, the temperature was adjusted to 1525"C, and the first slag and metal samples were taken. The slag was picked up on the end of a cold Armco iron rod, whereas the metal was sucked into a silica tube. The wash metal composition was (in percent): 4.29 C; 0.022 S; 0.021 P; 0.38 Si. The slags used were of four fixed starting compositions covering a wide range of acid-base ratios shown in Table I. Deliberate variations in MgO were made in these slags to check the role of MgO in blast-furnace desulphurization. Changes due to additions and reactions were followed by analysis of samples. Additions of Mn and MnO were made to most of the heats to note the role of Mn and MnO on desulphurization. Three heats (62 through 64) were made in an open pot induction crucible (graphite) using a

Jan 1, 1952

By K. S. Benson

DEPLETION is a subject of vital importance to the mining industry. Yet, in spite of its importance, its significance is not generally understood. The purpose of this discussion is to clarify the main aspects of the subject from the viewpoint of a metal mine taxpayer. To define the term depletion, it is necessary to distinguish among its various uses. In the economic or geological sense, depletion means the exhaustion of a natural resource. A mineral deposit is a wasting asset and once exhausted is nonrenewable. Millions of years were needed to produce an ore deposit, which may be consumed in a few years and which cannot be replaced except by the discovery of new sources of supply. The wasting asset feature of the mining industry has a vital bearing on the impact of the Federal Income Tax Law on this industry. This is recognized in the law by the various provisions dealing with the depletion allowance, and in this sense the term depletion has an income tax meaning. Depletion from the tax viewpoint means the statutory deduction from gross income designed to permit the return to the taxpayer of the capital consumed in the production and sale of a natural resource. The mining enterprise realizes income on the extraction and sale of minerals and a portion of the income realized represents capital consumed. As the resource is exhausted, the mining enterprise approaches the end of its existence unless new sources of supply can be acquired. Depletion from the tax viewpoint is a creature of statute with limited meaning and application and, in essence, is a method for amortizing the value of the primary asset of a mining enterprise. An example can best illustrate the significance of depletion from the tax viewpoint. Compare a manufacturing concern with a mining company. In computing taxable income of a manufacturing concern, consideraion is given to the cost of producing such income, the principal costs being capital investment for plant and equipment, labor, and raw materials going into the products produced. A mining enterprise, on the other hand, is faced with a different problem because its principal asset is the natural resource which it is producing. In computing its taxable income, consideration is given also to its capital investment for plant and equipment and the cost of labor; but in addition, recognition must be given to the fact that a portion of the proceeds realized on the sale of mineral represents capital. Without such recognition, the mining company would be taxed not on income but on capital and income, and Congress has never intended that capital be taxed as income. Thus, when depletion allowable is referred to in the mining industry, it means the statutory deduction allowable in computing taxable income of a mining enterprise. For guidance the appropriate provisions of the Internal Revenue Code, Income Tax Regulations, and the judicial decisions interpreting and construing them must be examined. It is important to identify and distinguish three methods of determining the allowance for depletion: 1—Cost depletion, 2—Discovery depletion, and 3—Percentage depletion. The basic method is cost depletion and in addition some taxpayers may be entitled to use discovery depletion and other taxpayers may be entitled to use percentage depletion. Discovery depletion and percentage depletion, however, are mutually exclusive and if a taxpayer is entitled to percentage depletion, he is not entitled to discovery depletion. By statute, a metal mine taxpayer is entitled to use cost depletion or percentage depletion, whichever produces the highest deduction. Thus, discovery depletion is merely of academic interest to such taxpayers and to most others. Briefly and broadly speaking, these methods of determining depletion may be described as follows: 1—Cost Depletion: Under this method, the allowable deduction for depletion is based upon the cost of the particular deposit to the taxpayer, unless the deposit was owned prior to Mar. 1, 1913, in which case the taxpayer may use the fair market value of the deposit on that date or actual cost, whichever is higher. This method is sometimes described as basis depletion or adjusted basis depletion, but in this discussion it will be referred to as cost depletion. 2—Discovery Depletion: Under this method, the allowable deduction for depletion is based on the fair market value of the deposit at the date of discovery or within 30 days thereafter and was originally designed to take into account deposits discovered subsequent to Feb. 28, 1913. 3—Percentage Depletion: Under this method, the allowable deduction for depletion is based on a specified percentage of the income realized during the taxable year from a particular property. As stated, the concept of depletion is based upon the exhaustion of a natural resource as distinguished, for example, from the concept of depreciation based on the exhaustion of property used in trade or business. From the tax viewpoint, depletion first became important in the administration of the Corporation Tax Act of 1909, which provided for an excise tax on net income. As soon as this act went into effect, mining taxpayers attempted to claim a deduction for depletion in computing net income although there was no specific mention of a deduction for depletion in the statute. The courts in these cases uniformly held that the statute did not permit an allowance for depletion in computing net income and also held that the provision permitting a reasonable allowance for depreciation did not include depletion. These early cases are quite significant because they establish the principle that the

Jan 1, 1952

By A. J. Lynch, J. A. Holmes, F. C. Bond, D. W. Fuerstenau

This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = C dx/xn either C or n must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant.

Jan 4, 1958

The opening session was held on Tuesday evening, June 28th. Mr. F. S. Witherbee, of Port Henry, a member of the Local Committee, welcomed the Institute as follows: Mr. President and Gentlemen and (if I my also add) Ladies of the Institute: In the absence of the Chairman of our Local Committee it is my pleasant duty to give you a cordial welcome once more to the shores of Lake Champlain. I think some fourteen years have passed by since we last had the pleasure of receiving you at a meeting in this vicinity ; but the pleasure of that meeting still lingers in our memory; and the profit which we derived from your discussions and from your presence with us has made us heartily desirous to have you here again. If the truth must be known, we were for a time much embarrassed by the difficulty of providing adeqriate and comfortable shelter for the large number of friends whom we hoped (and, as this assembly indicates, had good reason for hoping) to receive. But the liberality and zealous co-operation of the Delaware & Hudson Canal Company and its hotel manager, in offering to open Hotel Champlain, at no little inconvenience, before the usual time, presented a solution of this difficulty, provided the date originally proposed for the meeting could be changed to a week later. This change was duly authorized; .and I think you will all agree with us that it was wise.. At all events, I am sure, I now need offer no apologies for the roof which covers yau. During the fourteen years which have elapsed since your last visit to us, great strides have been made in the industrial development of this country. The meetings of the Institute, held from one end of the land to the other, have permitted you to witness the transformation of small hamlets? like Birmingham, Ala., into populous and thriving industrial centers. You have seen the Minnesota and the

Jan 1, 1893

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world&apos;s supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee&apos;s production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Chas. A. Ashburner

THE Bradford Oil District lies in the northern part of McKean County, Pa., and the southern part of Cattaraugus County, N. Y. Although petroleum was first found in the producing sand in 1871, it was not until the early part of the year 1875 that a productive horizon was acknowledged to exist, even by those most largely interested in the production of the crude oil. It has been reported to me that the first well drilled in the valley of the Tuneangewant Creek (commonly called Tuna Creek) was drilled by F. E. Dean and brothers in 1865. This well was located on the Shepherd farm, near the present site of Custer City. One hundred and sixty feet of drive pipe was used, and the hole was drilled to the depth of 900 feet. The producing sand at Custer City is found about 1130 feet below the level of the railroad track. The Shepherd farm well was therefore abandoned over 200 feet above the top of the oil sand. The next well was drilled by the Dean brothers on the Clark farm at Tarport. Drilling was stopped at a depth of 605 feet, or over 400 feet above the top of the oil sand. In the year 1862 the old Bradford well, since known as the Barnsdall well, was drilled to a depth of 200 feet with a spring pole, and then abandoned. In the spring of 1866 the citizens of the village of Bradford concluded to club together and sink the Barnsdall well deeper. It was drilled to a total depth of 875 feet, or to within 150 feet of the Bradford producing sand. All of these wells were drilled with the expectation of finding the Venango County oil, and at

Jan 1, 1879

By J. Leland Myer

IN a precise study of Pennsylvania anthracites, the research on European. anthracites is of little value to us because of their different physical and chemical nature. Likewise, there can be little correlation with the physical properties of bituminous and lower rank coals. Although all high-rank coals are thought to have had a common origin, microscopic examination revealing essentially the same kinds of organisms in similar .states of preservation, the different physical properties apparently arise from the degree or kinds of metamorphism of these coals. Representative samples from the Pennsylvania deposits have been selected for analysis, together with graphitic anthracite, bituminous coal, and some of the common forms of carbon. A complete list, with descriptions, is shown in Table 1.

Jan 1, 1932

By P. E. McKinney

Developments in engineering during the past decade, particularly as applied to marine construction, mining machinery and other purposes in which corrosion offers a serious problem, have created a large demand for a non-ferrous metal highly resistant to corrosion and at the same time useful in general construction work as a substitute for steel without materially decreasing the factor of safety or increasing the weight of the various parts over that ordinarily used in the case of mild steel. To obtain the combination of desired properties many compositions have been proposed and used with excellent success, but at the present time probably the most popular and most widely used combination is the non-ferrous alloy commonly called manganese bronze. This is nothing more than a high brass to which have been added, by the proper method of alloying, comparatively small percentages of aluminum, iron, or manganese with the definite purpose in view of strengthening the alloy and rendering it more dense and close-grained than the average yellow-brass casting. In the manufacture of manganese bronze a great deal has been said about the importance of using only the highest grades of raw material and the beneficial or detrimental effects, as the case may be, of various impurities, as well as the importance of adding the ingredients according to various formulas proposed; but in most of these cases the literature on the subject has dealt principally with the manufacture of this alloy from virgin metals and raw materials of the highest purity. It is the purpose of this paper to deal particularly with the possibilities that lie in the proper development of methods for manufacturing such an alloy by more economical methods than those which have usually been discussed in other literature on the subject. Shortages have recently existed in raw materials needed for many products entering into the various branches of engineering work, particularly the non-ferrous metals, and during the next few years of reconstruction the country will be flooded with many

Jan 1, 1919

By W. E. Wrather

The overproduction of crude oil in 1927 has received such widespread publicity, both within and without the industry, and the several factors which have brought about this situation are so thoroughly agreed upon by everyone, that it is unlikely the writer will in this brief review be able to contribute anything new. The entire story of low prices and demoralization revolves around two flush districts, Seminole and West Texas— the actual. performance of Seminole and the potential threat of West, Texas. The sustained production of California has been a contributing factor to this situation also. It seems reasonably certain that Seminole and West Texas will together dominate the industry during 1928, with Seminole probably destined to drop into second place, as additional pipe lines are completed into West Texas to care for its rapidly expanding production. It now appears inevitable that the production of 1928 will equal or exceed that of the past year, depending solely upon the rapidity wit,h which it is possible to market West Texas crude, and the degree of restraint which operators are willing to impose upon themselves in holding proved reserves of oil underground. Adversity has cultivated the growth of a promising spirit of cooperation which has accomplished practical results both at Seminole and in West Texas. Cooperation among oil producers has long been ardently hoped for, but prior to the past year it has never been effective on an important scale. The interests both of the industry and the public at large can best be conserved by cooperation in controlling production, and the widespread acceptance of this idea has paved the way for a more rational policy in the immediate future Production BY Major Districts The domestic production of the United States during 1927 amounted to 894,43.5,000 bbl. (Bureau of Mines), an increase over 1926 of approximately 128,000,000 bbl. California succeeded in maintaining its position of the past four years at 230,000,000 hbl. In 1923 with the Los Angeles

Jan 1, 1928