Search Documents

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By Paul R. Smith

Preparation for flotation begins with dragline mining, pumping, washing, screening, and desliming. Slimes, nominally -150 mesh material, constitute large quantities of phosphate and water which are a disposal problem. Older techniques involve sizing at about 35 mesh for separate coarse and fine treatment. The plus 14 mesh fraction does not require concentration. Coarse treatment includes agglomerate spiralling, belt flotation, thickening, scrubbing with sulfuric acid, de-oiling for reagent removal, and cationic flotation of fine quartz. A recent trend is to screen at coarser than 35 mesh size and eliminate coarse particle treatment, sacrificing some grade of this product. Techniques for flotation concentration of the fine size fraction are discussed.

Jan 1, 1976

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By H. S. McQueen

THE central Ozark region of Missouri has inter-ested geologists and mining engineers for many years. Of particular interest are the mineralized sink-hole type deposits, some of which have produced large quantities of iron ore. Deposits of coal are also known in this part of the State, and in mode of occur-rence are similar to the iron ore deposits. Occurring in the same general area, and often associated with coal, are deposits of high-grade non-plastic flint fire clay, and high alumina or diaspore clay. At present these clays are the most important materials being mined from the sink-hole type deposits. Deposits of high-grade flint fire clay have been known to occur in this region for many years, the Kelley pit near Rolla, Phelps County, being discovered in drilling for iron ore shortly after the close of the Civil War. Mining operations had disclosed at an early date masses of rough, open-textured "sandy" clay associated with the flint fire clay. Some of the hard flint clay also con-tained rounded shot-like particles of "sand." Both types of clay were considered of inferior grade and unsuited to the manufacture of fire brick. These clays were discarded in mining as value-less, in some instances being used for road metal. Some knowledge of the high alumina content of this sandy material had been obtained by 1908 1, and by 1917 the high alumina content was gen- erally known, and commercial shipments of what is now called diaspore clay were being made. These deposits of diaspore clay associated with flint fire clay form the only known deposits of commercial importance in North America. The production of diaspore and flint fire clay at present exceeds that of any former year. Statistics covering the production and value of the former were not collected prior to 1922, and the figures given below do not cover the tonnage of clay mined by companies and used in their own plants, so that the total produc-tion probably is much larger than that indicated. The figures were collected by the U. S. Geological Survey and the U. S. Bureau of Mines in cooperation with the Missouri Bureau of Geology and Mines.

Jan 6, 1928

By A. L. Holley

The members of the society are doubtless aware that the production of American Bessemer steel works is constantly increasing; that the same converters and machinery are doing more work every year. This enlarged output is due to various causes, chiefly the following: 1st. Better organization—better knowledge on the part of both managers and men, of the plant and the process; of the way to economize the more exhausting labor, and of the arrangement of the details of labor and operations so that they shall not conflict; also, more pluck—a greater willingness to take risks, or, more properly, such an intimate knowledge of the nature and capacities of the refractory linings in various stages of disrepair, and the probable be- . havior of the fluid metal at various stages of its treatment, that the precise nature of the risk may be better known, so that the works may be crowded to their full capacity. In the early practice, after getting four or five consecutive heats in a day, the men preferred to " let well enough alone," and to devote the remaining time to preparation for another turn. Now, thirty, and sometimes forty heats are regularly made during the twenty-four hours, day after day, without the frequent occurrence and without the fear of breakdowns or " messes," as the spilling of steel charges was graphically named in Sheffield. 2d. Although no new refractory materials have been developed, improved means of preparing such as we have, and of imbedding

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition With property valued at more than three-quarters of a million dollars, and with con¬siderable sums in various funds and endowments, it is possible to spend on each member of whatever class $22 65 each year, more than the maxi¬mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all To do this has required close management and a strict regard for our limitations In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a` number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initia¬tion fees to the General Reserve, and still only reduce the cash balance $2,074 54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratui¬tous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds.

Jan 1, 1923

By Axel Sahlin

Having no business interest in any of the various machines used for granulating ores, my remarks on the subject are prompted solely by my desire to contribute towards the determination of the best apparatus such information, as I have been able to gather,

Jan 1, 1893

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By Lawson P. Entwistle

SUMMARY ONE of the important reserves of manganiferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which have been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. From a noselike protuberance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (1) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena. The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale.

Jan 1, 1944

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By John B. Knaebel

The annual Jackling Award Lecture, sponsored by the Society of Mining Engineers of AIME, is intended to honor and commemorate one of the greatest mine-makers of all time, an innovator whose vision and determination made ore out of waste rock. He ushered in a new philosophy of mining which revolutionized some segments of the industry and notably affected our economy generally. To have been asked to given the Jackling Lecture this year is an honor that I scarcely deserve, but which I have accepted in humble gratitude. Although it is true that "many a mine has made the man," it is also true that while ore bodies are found, mines are made. That statement has been hammered into my skull many times by a man whose own career exemplifies its truth, a man who has been first and last a steadfast friend, who for a while was my boss and mentor, and who as one of this country's great mining geologists has laid his hand to the making of many a mine. I will doubly cherish the memory of the honor bestowed upon me because the presentation of the Jackling Award was made by this man. After the Lord made Dick Hunt he threw away the mold. Metals and other mineral products are essential ingredients of the social economy of the modern world. No well informed and thoughtful person can doubt that they will be indispensable to mankind as long as the fabric of civilization as we know it today can be held together. They are mined from ore bodies, which, unlike some other kinds of bodies, are physically inorganic and wholly incapable of reproducing themselves. Since in time they become mined out, an endless procession of new producers must be made by someone if the fundamental needs, to say nothing of the not so fundamental whims of an affluent society, are to be gratified. In saying that these mines must be made, I mean exactly that. It is my purpose to comment upon some of the problems we must cope with in making them. I shall try to avoid dwelling needlessly upon aspects of new mine development with which most people in this business are thoroughly familiar, and will attempt to discuss in a useful way some of the newer and more significant features of the economic climate in which these endeavors must be conducted. To begin with, an Almighty force put the ore into the ground, and selected the places in which to put it. Mankind was not consulted. Beyond that stage, however, mankind must find the ore deposits and contrive to extract their contents and put them into useful service. In doing this, he must use tools and techniques devised by man to overcome obstacles created in part by nature, but also in part by man himself. And most importantly of all, in making the tools and applying the techniques, he must use people. In the whole process the most pliable ingredient at hand-and also the most unpredictable-is people. Mines play out, and men die. As time goes on, we will have new mines, and they must be made by new men. The Environmental Dilemma It is perhaps timely to touch first upon the newest and in many ways the most potent consideration affecting the feasibility of developing new mines-the problems related to protection of the environment and to the

Jan 1, 1973

By Frank W. Osterwald

Violent, spontaneous destruction of coal faces and ribs during, what are commonly called, bumps endangers and at times destroys life and property in mines of the Book Cliffs coalfield, Carbon County, Utah. Because these mines supply much of the coking coal for the West Coast steel industries, mining is necessary, although costs are high and operating conditions are very difficult at times. As operations continue, mining will go to greater depths, and the difficulties will increase. Whether or not mining can be continued successfully depends in part on whether or not incidence of bumps can be controlled successfully. For this reason, the U.S. Geological Survey, at the request of and in cooperation with the U.S. Bureau of Mines, undertook a study of the Sunnyside No. 1 mine to determine what geologic factors were related to the incidence of bumps. This report presents the preliminary results of that study and indicates that some observable geologic features in the mine may be related directly or indirectly to bumps, and that other features may be used to infer stress distribution around workings that will aid in design of roof support measures. Coal is mined in the Sunnyside No. 1 mine from depths as great as 2500 ft by room-and-pillar methods. The surface topography is rugged with many steep cliffs and deep canyons, hence the load on the coal varies greatly within short distances. Much of the Sunnyside coal is under high stress, and while being mined, it shatters continuously' and falls from the face. Continuous shattering (bumping) makes mining easy, but if the shattering is interrupted, greater stress is built up and violent bumps may result when the coal is mined.

Jan 4, 1962

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950

By Prof John E. Church

It is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By R. W. Raymond

EDWARD COOPER, was born in New York City, October 26, 1824. His father, Peter Cooper, to say nothing of manifold reasons for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment of public schools; and it is not surprising that he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia. College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.* For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the strident of those data which the modesty of the man permitted to be placed upon public record. Edward Cooper's mind was one of the most active, accurate and subtle with which I have ever come into contact: He had inherited from his father a sunny, benevolent temperament, and' the irresistible impulse to attack all new problems which challenged his attention. His thorough education had 'indeed made him wiser than his father, both in philanthropy and in technical inventions. He could condemn and reject a proposition which Peter Cooper would have embraced, in a splendid, though ignorant, faith that nothing was impossible to an. American, and that the word ? impossible " was simply a label,

Jul 1, 1906

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By Paul Queneau

FROM the first days on the Norman beaches to the last days on the Elbe the Army Engineers of World War II lived off the countryside for the great bulk of the construction supplies needed for the fulfillment of their ultimate mission-to keep the army moving. To accomplish this end, vast tonnages of rock, timber, and steel were required in the construction of roads, railroads, and bridges. Combat Engineer battalions operated quarries under shell fire as a routine matter. An Engineer forestry company was decimated while cutting bridge timber on the Siegfried line. Oneof the more spectacular feats of the Army Engineers in obtaining construction materials was the operation of the Hadir Steel Works during the fall and winter o f 1944.

Jan 1, 1946

By George C. Howard, P. P. Scott

During the drilling of wells, fractures which are created or widened by drilling fluid pressure are suspected of being a frequent cause of lost circulation. A study of the variables which are believed by the authors to he related to fracturing led to the premise that the presence of an effective lost circulation material in a drilling mud stream would serve to plug small fractures at the moment they are encountered or created and thereby a a possible cause of lost Circula. tion by preventing fluid pressure from widening and extending the fractures. A large number of lost circulation materials were classified and tested in simulated fractures and in shallow wells. Granular type materials with a gradation of particle sizes were found to be the most effective for plugging. Within the limits of pumpahility, the concentration in mud of each lost circulation material tested was found to be a controlling factor in determining the maximum size fracture which could be sealed. A new type centrifugal sorter was given preliminary tests and found to be capable of concentrating cuttings for rejection and reclaiming lost circulation materials. INTRODUCTION The control and prevention of lost circulation of drilling fluids is a problem frequently encountered during the drilling of oil and gas wells. Lost circulation or lost returns may be defined as the loss to formation voids of the drilling fluids or cement slurries used in the process of rotary drilling and well completion. The loss may vary from n gradual lowering of mud level in the pits to a complete loss of returns. Not to be confused with lost circulation is the continuous reduction in mud volume caused by the loss of the fluid phase of muds as filtrate and the solid phase as filter cake during the continuous filt~ation process which occurs on permeable formation surfaces. The loss of drilling fluids and their costly constituents is only one of the detrimental effects experienced when circulation is lost. The loss of drilling time, plugging of potentially productive formations, stuck drill pipe, blow-outs, excessive inflow of water, and excessive caving of formatioils are other effects which contribute to make the control and prevention

Jan 1, 1951

By P. P. Scott, George C. Howard

During the drilling of wells, fractures which are created or widened by drilling fluid pressure are suspected of being a frequent cause of lost circulation. A study of the variables which are believed by the authors to he related to fracturing led to the premise that the presence of an effective lost circulation material in a drilling mud stream would serve to plug small fractures at the moment they are encountered or created and thereby a a possible cause of lost Circula. tion by preventing fluid pressure from widening and extending the fractures. A large number of lost circulation materials were classified and tested in simulated fractures and in shallow wells. Granular type materials with a gradation of particle sizes were found to be the most effective for plugging. Within the limits of pumpahility, the concentration in mud of each lost circulation material tested was found to be a controlling factor in determining the maximum size fracture which could be sealed. A new type centrifugal sorter was given preliminary tests and found to be capable of concentrating cuttings for rejection and reclaiming lost circulation materials. INTRODUCTION The control and prevention of lost circulation of drilling fluids is a problem frequently encountered during the drilling of oil and gas wells. Lost circulation or lost returns may be defined as the loss to formation voids of the drilling fluids or cement slurries used in the process of rotary drilling and well completion. The loss may vary from n gradual lowering of mud level in the pits to a complete loss of returns. Not to be confused with lost circulation is the continuous reduction in mud volume caused by the loss of the fluid phase of muds as filtrate and the solid phase as filter cake during the continuous filt~ation process which occurs on permeable formation surfaces. The loss of drilling fluids and their costly constituents is only one of the detrimental effects experienced when circulation is lost. The loss of drilling time, plugging of potentially productive formations, stuck drill pipe, blow-outs, excessive inflow of water, and excessive caving of formatioils are other effects which contribute to make the control and prevention

Jan 1, 1951