Search Documents

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y'-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y'-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937

By G. Carman Ridland

IN conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Müller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties.

Jan 1, 1943

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By Alexander Bowie

IN many places throughout the Western mountain plateau regions of the United States coal beds in place have been burned over very extensive, areas, the fire evidently originating on the nakedly exposed outcrop of the coal bed and gradually burning its way into the bed for considerable distances under very heavy cover. . The surface evidences of the burned-out coal beds are seen in the calcined and discolored rocks overlying the places of the outcrop. The greater the mass of the burned coal the higher the results of its combustion can be seen in the overlying strata. I have noted many instances of this condition in the States of South Dakota, Wyoming, Colorado, New Mexico, and Arizona. In the lignite fields of Dakota and Wyoming I noted stretches of level country many square miles in extent where the surface rocks were roasted and vitrified by the burning of a great bed of lignite lying nearly level and with a light cover; this is probably the most favorable natural condition for the burning out of a coal bed. The less the depth of the rock covering overlying the coal bed, the better the .chance for a continuous supply of air to the fire; but when the coal bed clips heavily into the ground, or even if level, if it, passes under a hill or mountain which gives the bed a heavy covering of strata, the fire has more chances of being extinguished from natural causes than in the first condition described. The distance which, a crop fire may extend into a coal field is very much influenced by the dip, the thickness of the coal bed, and the nature of the rock covering immediately overlying it.

Jan 2, 1914

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By N. R. Tipman, G. E. Agar, L. Paré

The flotation chemistry of the commercial INCO matte separation process was investigated. The slow cooling of Bessemer converter matte forms discrete phases of Cu2S and Ni3S2 and a Cu-Ni alloy. After magnetically removing the alloy, the Cu2S and Ni3S2 are separated by flotation at pH 12.4 (saturated lime) using diphenyl guanidine (DPG) as both collector and frother. DPG has been used exclusively in this flotation process because of its unusual selectivity for copper minerals. The surface product resulting from chemisorption of DPG onto theCu2S was identified as the double salt CU(DPG)2SO4.CU(DPG)2(OH)2. The adsorption followed Langmuir behaviour up to a monolayer coverage. In the absence of DPG, the rapid adsorption of oxygen by Cu2S in flotation pulps was observed. The surface product was identified as the insoluble basic copper sulfate CuS04.3Cu(0H)2 with the production of sulfate ion. In the presence of DPG, the oxidation reaction appears to be suppressed. The frothing properties of DPG and commercial frothers were compared. DPG is not a powerful frother. Batch flotation tests confirmed that DPG is a highly selective collector when compared to most sulfhydryl collectors.

Jan 1, 1976

By Michael M. Maier, Charles B. Brumleve

The Henderson mine uses the panel caving method to extract molybdenum ore from a deep ore body in an igneous intrusive. Research into caving mechanics and its related problems has yielded fundamental relationships concerning the response of a stressed rock mass to the caving method. The relationships studied through a variety of programs include the following: the evaluation of time and distance related stress fields; the monitoring of the deformation of underground openings and the design implications; ground and mining sequence classifications compared to past support requirements; the response of finite rock masses to zones of high stress concentrations; the evaluation of the subsidence induced by caving; and the microseismic monitoring of cave growth. The cumulative objective of this research is to better understand, predict, and control rock mass response.

Jan 1, 1981

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situaated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way.

Jan 11, 1957

By Irwin Roman

NUMEROUS results and formulas have been published for analyzing seismic records, but most of them apply only to large-scale phenomena such as are encountered in studying earthquakes. In a few cases,1 formulas have been published for some of the simpler structures. In the present paper, an attempt will be made to analyze several types of struc-tures without using methods more advanced than those of a first course in calculus. In, tracing a disturbance through a medium, it is almost always possible to base the analysis on Fermat's Principle of Extreme Time, which states that waves of displacement travel between points in such a manner as to make the time of travel an extremum with respect to all neighboring paths. In the simpler cases, comprising most of those used in optics or geophysical prospecting, this time is a minimum and the principle is often referred to as the Principle of Least Time. Within a homogeneous medium, having a uniform speed of transmission of the disturbance in all directions and throughout the medium, the paths are straight and are refracted at the interfaces in accordance with the Snell law of refraction, which states that the ratio of the sine of the angle, made by the ray with the normal to the interface, to the speed of trans-mission is the same on both sides of the interface. Thus, in any medium composed of homogeneous sections, this same ratio has a constant value at all points. In particular, if all interfaces are horizontal, it is apparent that the angles of incidence are the angles made by the ray with the vertical direction. Furthermore, the incident ray, the refracted ray and the normal to the interface are all in the same plane at each refraction;

Jan 1, 1933

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

General discussion on the above subject, presented at the Pittsburgh meeting, October, 1914. GEORGE S. Rice, Pittsburgh,. Pa.-Undoubtedly there is a serious problem through the juxtaposition of gas and oil wells and coal mines, not only at the present time, but possibly of far more serious import for the future. If one examines a map of the coal fields on which is superposed the oil and gas fields of the country, one finds that they overlap to a very great extent. I may say at the beginning that we have not, so far as I know, had any very large number, of accidents growing out of this situation causing loss of life. Such accidents, or rather incidents, that have occurred have all been rather potential possibilities for disasters due to the leakage of gas from wells into the adjacent coal mines. The condition has been most acute in the Fairmont district of West Virginia, and in the general coal fields southwest of Pittsburgh in Pennsylvania. The accidents which have actually occurred were summarized in Bulletin No. 65 (Oil and Gas Wells through Workable Coal Beds) issued by the U. S. Bureau of Mines, reporting the transactions of several meetings in Pittsburgh, February, 1913, of oil and gas well representives, State geologists, State mine inspectors, coal-mine operators, and representatives of the U. S. Bureau of Mines. This conference was partly brought about through a case in which the Pennsylvania State inspection department had brought suit to restrain a gas company from completing a well through a certain mine. The office of the Attorney General of Pennsylvania asked the opinion of the Bureau of Mines upon the matter; about the same time the Association of State Geologists, at its New Haven meeting, asked the Bureau to take up the problem. Accordingly, it was thought advisable to bring together the several, interests. For the most part the danger is, I think, greater in the future, than at the present time Many parts of the coal fields of Pennsylvania, in Greene County particularly, have been penetrated by numerous wells very close together, and with the present practice of having a large coal pillar around each well, has made or will make the mining of many areas difficult or pro-

Jan 4, 1915