Search Documents

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By Alfonso Merlini

DIFFERENT explanations have been given by the two current theories of the annealing textures for the variation of annealing texture with the annealing temperature observed in rolled polycrystal-line aluminum,' copper,2 and brass, And in rolled single crystals of copperk and silicon iron.' The theory

Jan 1, 1957

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuitability or resistance to replacement, and (b) physical resistance to small-scale brecciation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1940

By C. B. Manula, H. Gezik

In planning modem-day mining operations, management needs to pass from the area of subjective decision-making to an area of objective decision-makirlg. Planning procedures currently being practiced by many mine managers depend primarily on common sense and trial-and-error methods which oftentimes never reach optimum solutions. For this reason, an attempt is made to provide an understanding of linear programming to solve production planning problems. More specifically, a linear programming model is proposed to solve the production scheduling problem as it was found to exist in the crushed stone industry. Optimal production scheduling is of prime concern here, since the industry has to cope with seasonal demands for its products. The solution, as determined through the application of the model, provides management not only with an optimal production schedule but also with the following information regarding the improvement of existing facilities: (I) the location of bottlenecks which limit production and profit; (2) the directions in which the company i fixed equipment should be expanded or modified; and (3) the evaluation of unused resources. Future trends in stone production will quite likely parallel those in the construction industry. Continued record expenditures for structures such as dams, highways, and buildings are the reasons for this accelerated growth. Production forecasts for the next decade are predicted to be around one billion tons with an approximate 7% annual increase. The problem of increasing production from 570 million tons in 1966 to 1 billion tons by 1976 offers no small challenge. This situation is further compounded by other problems and economic factors. Population expansion, government regulation, labor agreement, and changes in technology wd cause managers and operators to be confronted by many more complexities than characterize present-day operations. Some of these. problems and economic factors are: (1) In some metropolitan and other urban areas, easily accessible sources of stone are almost depleted. Transportation costs will be a prime concern of the industry. (2) Population growth has forced residential expansion to a point where many quarry operators must conform to urban and suburban regulations. (3) Government regulation in regard to air and water pollution, noise, and reclamation as well as zoning developments necessitate that crushed stone producers keep abreast of changing conditions and requirements. (4) The crushed stone industry operates under pressure of a highly competitive situation. Every company's objective is to retain a favorable marketing position by exercising great attention to production and marketing costs. This is rather difficult, since the crushed stone industry is one segment of modern mining which has to cope with a seasonal demand for its products. Among the problems posed here, the one of exercising great attention to production and marketing costs is of current interest to management. Under seasonal demand conditions, this problem creates further difficulties for managers who need to plan and forecast. STATEMENT OF THE PROBLEM Various methods of Operations Research have been developed to handle a problem whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. This paper describes the use of Operations Research methods to solve a production planning problem when demand is seasonal. The seasonal production planning problem is an important one because of the substantial costs associated with changing production, employment, and inventory levels to adjust to seasonal sales patterns. Most companies try to operate within reasonable levels of employment changes and hold inventories within storage capacities. In general, little or no attempts were made to develop minimum cosl schedules or to provide objective means to compare various production policies. When demand varies within a fixed time period, 11:-oduction requirements may be met by following one

Jan 1, 1970

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By H. I. Altshuler

THE mines operated by the Compañia de Real del Monte y Pachuca, Pachuca, Mexico, are in two districts, the Pachuca, and Real del Monte. The principal area of mineralization is within a rectangle roughly 10 miles from east to west and 6 miles from north to south. It contains a number of veins from 2 to 20 ft. wide, which are exploited by this mining company. The scattered position of the producing mines led to the construction of two mills between 1906 and 1908; the Loreto mill, in Pachuca, averaged 2600 tons daily, and the Guerrero mill, in Real del Monte, milled 1270 tons daily. On Feb. 1, 1929, the management decided to enlarge the Loreto mill to take the combined tonnage of both mills at that time. This economic measure required the centralization of ore delivery, which would also afford a material saving in the cost of ore transport. The centralization would give the company the following advantages over the former system of operation: 1. Beneficiation at a single mill, closer to source of materials and supplies than the abandoned- Guerrero mill. The refinery is, also in the Loreto patio. 2. Ore delivery to surface at one point (San Juan Pachuca shaft) instead of at four. 3. Elimination of aerial tramways. To show what would be required to effect this centralization, it is necessary to describe the means by which the ore was delivered to the two mills, prior to centralization. The heart of the Real del Monte district is roughly four miles from that of the Pachuca section. The producing mines in these two districts were: Pachuca district: Santa Ana mine Camelia group

Jan 1, 1934

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By John Mark Patek

Knowledge of the relative floatability of silicate minerals is increasing in importance as flotation is being applied to the concentration of nonsulfides. Many silicates are in themselves commercial products amenable to concentration by flotation. Moreover, the selective flotation of other nonsulfide minerals, such as cassiterite, depends largely upon the floatability of associated gangue silicates. Differences in floatability existing between the various silicates have not- been sufficiently appreciated; for example, the feldspars that differ greatly in floatability have generally been merely treated as "feldspar." It was the purpose of the work described in this paper to determine by experiment the differences in floatability between silicates; to investigate the causes for such differences, and to discover a means of predetermining approximate floatability without the necessity of experimentation. Determining Floatability The relative floatability of 20 silicates so selected as to represent all of the more common silicate types1 was obtained by flotation tests enumerated in Table 1. The mineral to be floated was crushed dry on a steel plate, and screened repeatedly during crushing through an 80-mesh screen in order to produce a sand with all grains as close to 80 mesh as possible. The sand was placed in dilute (6N) hydrochloric acid until free of soluble foreign material, and then washed with tap water about ten times in order to remove both acid and fines. The resultant product, which averaged 82 per cent plus 200 mesh, was floated in 50-gram charges in a 50-gram Denver celluloid flotation machine with 0.008 gram of terpineol, and from 0.01 to 0.05 gram of oleic acid in a solution acidified with sulfuric acid. The degree of separation of one mineral from another was determined by counting under a nlicroscope the grains of each mineral, both in the concentrate and in the tailings, and comparing their relative abundance in each. Unless the comparison showed a decided difference in amount,

Jan 1, 1935

By J. Brett, S. Friedman

A study of the diffusion of nickel into both fibrous and recrystallized 0.065-in.-diam silica-alumina doped tungsten wire at 1200°C has been conducted. The diffusion profiles were determined by chemical dissolulion of successive circumferential layers and spectro-photometric determination of nickel in the etchant. It was shown that the diffusion of nickel into tungsten is markedly structure-sensitive. No significant amount of nickel could be introduced at 1200°C into tungsten which had first been recrystallized at temperatures of 2300°C, leading to an upper limit estimate for the bulk diffusivity of nickel in tungsten of 10-11 sq cm per sec at 1200°C. However, nickel did diffuse into initially fibrous wires, caused re crystallization, and was alsays present at the advancing recrystallization front. The accumulation of nickel in an initially fibrous region ceases when the recrystallization front arrives. The characteristics of the resulting diffusion profiles are explained in terms of the relation between diffusion processes and micro structural changes. WHILE it is well-known that the presence of nickel and certain other metals causes low-temperature recrystallization of the cold-worked fibrous structure of doped tungsten,''' the character of the phenomenon is not well understood. Recently it was shown that the recrystallization reaction can be induced at low temperatures by the presence of solid nickel on the surface of doped wire, but not by exposure to nickel vapors.3 Once recrystallization was initiated, a continued source of nickel was required for propagation of the recrystallization front. The phenomenon appeared to be a complicated solid-state reaction since, in addition to the change in structure of the tungsten from fibrous to equiaxed grains, diffusion of nickel from the surface into the recrystallized and fibrous structures was occurring with possible chemical reaction between nickel and tungsten at the surface and interaction of nickel with the dopants which ordinarily stabilize the fibrous structure within the wire. The objective of the present work was to study the diffusion of nickel into fibrous and recrystallized tungsten structures in order to clarify the relationship of the diffusion process to nickel-induced recrystallization. Studies of interdiffusion in the Ni-W system4"7 have been principally concerned with the mobility of tungsten in nickel. Information on diffusion of nickel in tungsten is meager, and there seem to be no studies of the mobility of nickel in tungsten which elucidate the structural aspects of the phenomenon. The present experiments were designed to determine the diffusivity of nickel at 1200°C in fibrous tungsten, in large-grained tungsten prerecrystallized at high tem- perature, and in tungsten recrystallized at 1200°C due to the presence of nickel. Although the concentration profiles were determined in these experiments, unexpected changes in boundary conditions or complex diffusion paths complicated the analysis of these profiles so that the interpretation could not be readily expressed in terms of simple diffusivities. EXPERIMENTAL PROCEDURE The experiments were conducted on Sylvania 0.065-in.-diam silica-alumina doped commercial tungsten wire, hereafter designated as ordinary doped wire. A special lot of 0.065-in.-diam silica-alumina doped low-nickel wire was also used. Impurity analyses of the wire are given in Table I. The experimental design is shown in Fig. 1. All heat treatments were conducted in vacuum. Two groups of ordinary doped wire were prepared for diffusion with nickel. One group in the as-received (fibrous) condition was elec-tropolished, nickel-plated, and annealed at 1200°C for 20 and 40 hr, or was exposed to nickel vapor at 1200°C for 20 and 40 hr. The second group was recrystallized to an equiaxed grain structure at 2300°C for 3 hr, electropolished, nickel-plated, or exposed to nickel vapor for anneals at 1200°C for 20 and 40 hr.

Jan 1, 1969

By Benjamin L. Miller, Charles H. Breerwood

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Charles H. Breerwood, Benjamin L. Miller

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967

BLOCK CAVING HAS BEEN DEVELOPED to a high degree of efficiency in the last two decades and more particularly since World War II. At the Jeffrey mine of Canadian Johns-Manville Co., in the Eastern Townships of Quebec, several innovations have increased production and decreased costs. Asbestos ore is produced at the rate of 10,000 tpd from an underground operation supplemented by a large open pit that has been mined since 1881. The orebody consists of asbestos veins in a fractured and serpentinized peridotite. Hardness and structural strength of rock vary from soft shear zones at one extreme to a small amount of hard granitic inclusions at the other. In general the ore is weak and deteriorates on exposure to air, so that it is difficult to maintain underground openings for any period of time. Permanent workings are lined with concrete and temporary ones are driven mini- mum size and supported with steel sets as required.

Jan 5, 1954

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By V. C. Allison

The explosibility of a dust is favored by its fineness and content of volatile combustible matter; its explosibility is decreased by its moisture and ash content. The explosibility of a dust can be reduced by admixture of either inert dust or water. The major effect of both the inert dust and water lies in their heat capacity; they absorb the heat of the explosion flame until the temperature of this flame drops below the ignition temperature of the explosive heat. The amount of inert dust necessary to make an explosive dust non-explosive can be calculated from its proximate analysis. FOREWORD LARGE-SCALE testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparation of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments con¬ducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have been reviewed by the Bureau of Mines., The Bureau has conducted many tests with the Frazer-Clement2 apparatus, which gives the pressures set up when the dust cloud within is, ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. An attempt has been made to design an apparatus that may be used for checking and correlating the experimental tests. The first design was a wooden gallery, 8 by

Jan 7, 1925

By F. D. Rosi, F. C. Perkins, L. L. Seigle

An investigation was made of the mechanism of plastic flow in coarse grained specimens of both sponge and iodide titanium at low (-196°C) and high (500° and 800°C) temperatures. Deformation by slip occurs predominantly on a {1011} plane and in a <1120> direction over this entire temperature range, and secondary slip on {101-1} planes becomes more prevalent with overthisentireincreasing temperature.range, The crystallographic habit of the predominant twin planes becomes more prevalent with type is temperature-dependent, and deformation by twinning increases as the temperature of testing is lowered. Kink bands were not observed at -196OC and rarely at the high temperatures. A LTHOUGH the deform a tional mechanisms in . -titanium at atmospheric temperature have been extensively investigated," there is little information regarding the influence of testing temperature on these mechanisms. The only available data come from the recent work by McHargue and Hammond, who extended single crystals of iodide titanium at a temperature of 815°C. No significant changes in the types of slip and twinning planes were observed, but increased activity on the type I, order 1 pyramidal slip planes and on the type 11, order 2 twinning planes was reported. These planes contribute very little to the deformation process at room temperature.&apos;&apos; &apos; Since there is interest in titanium as a material for use at both low and high temperatures, the present investigation was undertaken to examine the slip and twinning behavior in coarse grained specimens of titanium at -—196", 500°, and 800°C in order to determine the general effect of temperature on the mechanism of plastic deformation. Experimental Material Used and Specimen Preparation—Both sponge and iodide titanium were used in the present investigation; chemical analyses appear in Table I. These materials were arc-melted under argon into 25 g slugs, which were then cold-rolled approximately 90 pct to a sheet thickness of 0.05 in. Since the strain-anneal technique was used for obtaining coarse grains, the cold-rolled sheets were made into tensile specimens which were then annealed to produce a relatively coarse uniform grain structure prior to critical straining. The details of the strain-anneal treatment. size of grains, and the method for preparing the specimen surface for optical microscopy have been described in a previous report.&apos; In order to obtain a wider spread in crystal orientation for the present work, it was necessary to vary the rolling schedule to reduce the degree of preferred orientation in the annealed sheets prior to critical straining. Methods for Tensile Testing—The apparatus for experiments at the temperature of liquid nitrogen (—196°C) consisted of two concentric stainless steel

Jan 1, 1957

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By O.W. Ellis

Recently there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2 alone gave reliable information in this regard. Even today his determinations of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time—their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systernatic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington, 16 Smalley33 and Thiband 45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper. The situation in regard to these alloys in 1926 was very clearly stated by an anonymous writer,47 in The Metallurgist of February of that year, whose remarks were so to the point that they are well worth quoting: It will he seen that there are still large fields remaining to be studied in each of these systems (those of the aluminum, iron, nickel and manganese brasses) before our knowledge is adequate. When we come to the more complicated systems the position is even less satisfactory, and on account of the very incomplete nature of the work which has been

Jan 1, 1929