Search Documents

By Tim Ross

Several shear failures were observed in Shaft #1 at the Mountain Coal Company, LLC, West Elk Mine, after mining longwall Panel 23, 1,100 ft to the east of Shaft #1. It was speculated that this shear damage could be related to differential ground movement caused by in situ stress relief from the ?stress shadow? of the caved zone above longwall Panel 23. A numerical study was conducted to assess the possibility of the shaft shear damage being caused by in situ stress relief and the potential for additional damage to Shaft #1 and two other nearby shafts, due to mining nearby longwall Panel 24. Three-dimensional (3D) models were built in FLAC3D to simulate past and future mining near shafts, the estimated local anisotropic and directional horizontal stresses, and the overlying variable surface topography. The numerical analyses indicated that stress relief due to mining Panel 23 caused the shear damage to Shaft #1and that additional damage to Shaft #1 and the other two shafts, would likely result from mining longwall Panel 24. Additional shear damage was documented in Shaft #1 when longwall Panel 24 was mined, confirming the results of the numerical analyses.

Jan 1, 2006

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By Brendan Donnelly, Lasitha Piyathilaka, Jung‑Hoon Sul, Sanghyun Jeong, Benjamin Probyn

Premature failure of armoured face conveyor (AFC) chains due to corrosion is a significant proportion of the unplanned downtime experienced on longwall equipment. The AFC chains are constantly in contact with water and wet coal. The premature failure issue of AFC chains has become more prominent since the introduction of longwall top-coal caving with its additional AFC. Reverse osmosis (RO) is a popular water treatment method for reducing salinity and dissolved solids, but its impact on the corrosion of the AFC chains is unclear. This study has been commissioned to investigate the direct effects of RO water on the corrosion of AFC chains. An immersion test was carried out using AFC chain steel submerged in two water samples: untreated dam water and treated water from an RO treatment plant. Elemental analysis was conducted for both water samples, and four corrosion indices were measured for both water samples. The RO water more vigorously dissolves calcium carbonate scales leading to increased corrosion of the AFC chains although the dam water has much higher levels of calcium, chloride, sulphate, sodium, and magnesium. Bicarbonate ions are the main alkaline factor of water that provides the buffering capacity to acids. Decreased alkalinity without balancing other ions in water causes high corrosivity and decreased scaling tendencies.

Oct 16, 2023

By Rob Farnfield

In the UK all new developments, including mines, quarries, tunnels, etc., are subject to a system of planning control. If the use of explosives is anticipated then such developments will attract a number of so-called ‘planning conditions’ relating to the blasting operation. This paper will outline a ‘typical’ set of conditions and how operators ‘plan to comply’. British Standards relating to both human and structural response are also reviewed and contrasted to the typical planning conditions previously outlined.

Jan 1, 2005

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By Antonio Nieto

According to the analysis of surface powered haulage accidents involving off-highway haul trucks in openpit mining, the U.S. Mine Safety and Health Administration (MSHA), reported 1,300 fatal accidents from 1990 to 2005. Of these, 163 were considered off-highway truck haulage accidents, and at least 23 involved collisions of an off-highway truck with a neighboring vehicle or a worker on foot (Nieto and Dagdelen, 2006). In general, an average of 18 nonfatal accidents and three fatal accidents occurred in openpit mining per year when equipment backed over the edge of an embankment, stockpile or dump point (Fessak, et al., 2003). The specific problems that need to be solved can be determined by carefully studying the accidents involving haulage trucks (Marrara, et al., 2004). Solutions to haulage truck safety must consider the human factors affecting each task even when engineering solutions seem most appropriate. In surface haulage, human performance becomes a critical issue because of the unusual demand the vehicle?s places on their human operators: ? Roadways and working areas change frequently in mining operations. ? The sheer mass of mining equipment such as trucks requires control inputs (e.g., braking) far in advance of the desired action. ? Rough roads, loading and unloading impacts can subject the driver to dangerous shocks and vibration. ? Visibility is sharply curtailed by the bulk of the vehicle generating large blind spots. All of the above issues can be attributed partially to the lack of visibility (Pyles et al., 2003). Driver visibility and communications are key issues to reduce mining truck accidents. Analysis of fatalities and injuries involving mining equipment demonstrates the need to develop new intervention and control strategies to mitigate the risks associated with mining equipment operation. Ongoing development of these and other new strategies is required to achieve a reduction of injury in the mining industry

Jan 2, 2010

By S Jephcott

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralised bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulfides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralisation. The geochemistry of the deposit has been investigated with respect to the stratigraphic column and mineralogy of the sediments. A sedimentary origin is advocated for the deposit. Volcanism, thermal spring activity and high salinities, perhaps related to the Emu Fault, are considered as contributing factors to ore genesis. The metallurgy of this deposit is discussed in relation to its geologic history.

Jan 1, 1971

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining CO.'s Granite Mountain shaft. How this, insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the fire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest producer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By E Lounejeva, J A Halpin, A Chappaz, D D. Gregory, S Wu, T Lyons, P J. Sack, R R. Large, S W. Bull

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Newly published models suggest that some orogenic and Carlin-style gold deposits formed by the remobilisation of trace elements during interaction with hydrothermal or metamorphic fluids from early sedimentary pyrite that was enriched in Au, As and Te. The released trace elements are transported by the fluids to favourable trap sites where they are deposited. Therefore, early enrichment of Au, As and Te in source rocks (particularly in pyritic black shale) can be crucial to the formation of orogenic and Carlin-style gold deposits.The most important cause of the enrichment of gold and other trace elements in the sedimentary basins has been examined in this study to determine which basins are the most prospective for the development of orogenic gold deposits. An important influence for Au and other associated trace element accumulation in sedimentary pyrite is the temporal variation of trace element content in the oceans, as revealed by a database of over 1400 analyses of pyrite from black shale through geologic time. It is inferred that sediments coeval with those where sedimentary pyrite is enriched in Au and associated trace elements are more likely to be source rocks of orogenic and Carlin-style gold deposits.Factor analysis of the trace element content of pyrite through geologic time was conducted to investigate the multivariate relationships amongst trace elements and how these chemical factors explain the uptake of trace elements. One important factor includes Te, Au, Pb and Bi content. The incorporation of these large cations into pyrite is enhanced by As3+ substituting for Fe in pyrite lattice. The As3+ ion occurs in relatively oxidised environments and, thus, it is expected that shales deposited in non-euxinic waters are better source rocks for orogenic gold deposits.The examination of both the time in which the sediments were deposited and the redox conditions of the basin, and the ocean more broadly, can be used as a guide to approximate the extent of a basin’s fertility. To illustrate the use of this exploration tool, examples from the unmineralised Jet Rock Formation (UK) and the mineralised Castlemaine Group (Bendigo, Australia) are presented in this paper.CITATION:Gregory, D D, Large, R R, Halpin, J A, Lounejeva, E, Wu, S, Bull, S W, Sack, P J, Lyons, T and Chappaz, A, 2015. Accumulation of trace elements into black shale – how to identify a viable source rock for orogenic and Carlin-style gold deposits , in Proceedings PACRIM 2015 Congress, pp 59–64 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Willem P. C. Duyvesteyn

"Scandium International Mining Corp (SCY) has been involved in the commercial development of its Nyngan Scandium Project for about ten years. Various studies at a variety of global R&D organizations have been carried out in an attempt to define the deportment of scandium in both the limonite as well as the saprolite phases of Nyngan ore to assist with process development. Technologies such as sulfuric acid baking, high pressure acid leaching, sulfuric and hydrochloric acid atmospheric leaching and heap leaching have been extensively investigated both at the bench and pilot scale level to arrive at the most economic process flow sheet that will be discussed in some detail in this paper. Solvent extraction, ion exchange and other refining technologies have been tested and an optimum configuration has been established for the Nyngan project which is expected to be the first primary scandium mine and metallurgical plant in the world.Because of a lack of product availability the current scandium market is limited to less than 20 tons per year. Technologies have been identified to produce product with different specifications for aluminum alloys and solid oxide fuel cell applications. Preliminary economics have identified that Nyngan will be a robust and low capital cost project that can readily be expanded as the size of the scandium market increases."

Jan 1, 2016

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

An efficient and portable mathematical model has been developed for simulating heat transfer in six-in-line slag-resistance-heating electric furnaces for smelting sulphide ores to produce base metals and platinum group metals. This model is a steady-state one relating furnace conditions and performances to various control and input parameters. Some transient effects occurring in electric furnaces are neglected for computation efficiency. This article describes the model development and modelling results. The present model is capable of predicting: (i) temperatures at various locations in a six-in-line furnace, such as slag bath, matte bath, solid charge, freeboard space, freeze lining, cooling water, and air gaps between solid material components, etc. (ii) freeze lining thickness, (iii)smelting rate, and (iv) heat loss rate, etc. A typical feature of the model is that it is easily portable to different application platforms and sufficiently efficient with execution times less than a few seconds. Therefore, it is possible to apply the model for online prediction and control of heat transfer and freeze lining thickness in industrial electric furnaces.

Jan 1, 2011

By R. Simonson

Agenda ? Need and Introduction ? Interface Management Programs ? Outcomes of Successful Interface Management ? Key Success Factors ? Lessons Learned ? Concluding Remarks Need for Interface Management ? Complex projects ? Larger in scale ? Physically dispersed and delivered remotely ? Involved with several stakeholders ? Risks thus imposed due to: ? Iterative and dynamic nature ? Large information flow ? Document revisions and information updates ? Related sources of Risk: ? Ineffective communication ? Poor work relationships ? Person to job mismatches ? Failure to clarify expectations

Aug 1, 2013