Search Documents

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By R. J. Hundermark

Keywords: Anglo American, Anglo Platinum Ltd, Waterval, Mortimer, Polokwane, ACP, pyrometallurgy, platinum, PGMs Anglo Platinum Ltd is the largest primary platinum producer in the world and operates three smelters in South Africa: Waterval, Mortimer and Polokwane. The operational details of the smelters are covered in previous reviews, thus only unit operations that have been upgraded are discussed. The most significant of the upgrades include the installation of a second ACP converter at Waterval Smelter in 2006 and the anticipated upgrade of Mortimer Smelter to 38MW in 2011. Several advances have been made in the smelting operations to improve the furnace stability and longevity. Control of the chromium input to each of the smelters has substantially allowed continued operations at levels below the spinel saturation point in slag, which results in lowered matte and slag temperatures. Mogalakwena concentrate, arising from the Platreef ore, is used to dilute high chromium-containing concentrates. In addition, furnace controls have improved in terms of crucible temperature and condition monitoring, improved feeding control, management of alarms and trips and having the quality of instrumentation and operational rigour required to support this. Advances have been made on the ACP converter in terms of good converter matte quality, and increased intensity and efficiency of operation. Combined with improvements to both the conventional and tower sulfuric acid plants, the emissions from Waterval Smelter have been reduced substantially since the introduction of the ACP. This is in spite of increasing metal throughput. The Anglo Platinum Ltd smelting operations have made significant progress since 2006 and further advances are envisaged to further improve on safety, reduce costs, increase efficiencies and throughput, while reducing emissions.

Jan 1, 2011

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively

By T. Mulja, Michel Boily, Anthony E. Williams-Jones, Pierre Pilote

"The Preissac-Lacorne batholith is composed of suites of early metaluminous calc-alkalic gabbroic to granodioritic intrusives, three late peraluminous monzogranite plutons and numerous Li, Be and Ta-bearing granitic pegmatites. The Lacorne pluton is dominated by biotite and biotite + muscovite monzogranites containing abundant Be and Ta-bearing granitic pegmatites (40-80% volume). The pluton is surrounded by swarms of unzoned or poorly zoned spodumene-rich pegmatite dykes. The La Motte pluton is composed of biotite monzogranites, biotite+ muscovite monzogranites and rare muscovite + garnet monzogranites. Li, Be and Ta-bearing pegmatites are less abundant than in the Lacorne pluton and are commonly associated with molybdenite bearing quartz-muscovite-K-feldspar veins. In the Preissac pluton, muscovite + garnet monzogranites and muscovite + biotite + garnet monzogranites are the dominant rock types. The pluton rarely contains granitic pegmatites and these are generally barren. However, numerous molybdenite bearing quartz and quartz-feldspar-muscovite hydrothermal veins are observed.Li, Be andTa-bearing pegmatites display a crude spatial zonation around their parent monzogranites. Spodumene-rich pegmatites are generally unzoned or poorly zoned and are confined to the surrounding metasedimentary or metavolcanic rocks or crop out in the early gabbroic to granodioritic intrusives surrounding the monzogranites. Ta and Be-bearing pegmatites are usually concentrated towards the margins of their parent monzogranites. The highly fractionated nature ofmonzogranites (high Rb/Sr, low K?Rb, Ba?Sr, Zr/Nb ... ), their peraluminous composition (corundum normative and muscovite bearing) and the numerous occurrences of Ta and Be-bearing pegmatite dykes represent important criteria for the exploration of fertile granites."

Jan 1, 1990

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering&apos;s Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering&apos;s Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1994

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By Anu Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Miner Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the NIOSH Bruceton Experimental Mine was pressurized using a 1.1 m (42 in) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010