Search Documents

By Fernando O. Boechat

Com a redução da oferta de minério granulado de boa qualidade no mercado mundial e as restrições ambientais à sinterização, as pelotas de minério de ferro passaram a ocupar um papel importante como matéria prima para produção de ferro primário. Entretanto, embora apresentem maior resistência à degradação, as pelotas ainda sofrem com este problema, embora em menor magnitude, quando comparadas com granulados. Pode-se identificar a degradação das pelotas de minério de ferro em duas etapas, durante o manuseio e sob redução. Uma vez que vários estudos já analisaram a degradação durante o manuseio, a degradação durante a redução torna-se um assunto relevante e pouco explorado. Assim, o presente trabalho avaliou as energias envolvidas no movimento da carga ao longo de um forno de redução direta do tipo Midrex, usando o método dos elementos discretos. Para isso, foi utilizado o software EDEM® para obtenção das energias dissipadas durante as colisões das partículas. Aplicando estas energias ao modelo mecanicista proposto por Tavares e Carvalho [4] para fragmentação das partículas foi possível estimar a taxa de geração de finos no interior do forno. Estes resultados foram utilizados na previsão da degradação mecânica de pelotas no interior do forno, que previu a geração de 1,2 a 2,6% de finos gerados em um forno Minimod®, dependendo das premissas usadas.

Aug 1, 2018

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By M. A. Schellhardt

The Bureau of Mines has made periodic back-pressure tests on numerous gas wells in the Texas Panhandle field luring the past several years to study the delivery capacities of the wells under different pressure and operating conditions and to determine the relationships between pressures and rates of delivery from gas wells.4/ However, information regarding the intake capacities of gas-well systems is meager, end in projects involving- the flow of gas into porous-rock reservoirs it has been necessary to determine intake capacities of gas wells by trial. Accordingly the fundamental intake characteristics of natural-gas wells have been studied to develop a method for determining intake capacities under different wellhead pressures from data descriptive of the "output" or producing characteristic of the wells.

Jan 1, 1936

By H. K. Shearer

Drilling for oil and gas in Arkansas in 1934 showed more activity than in any year since 1929; with a total of 96 completions, including 36 oil wells, 1 gas well and 59 dry holes. Of the producers, the lone gas well and 35 oil wells were in old fields, and one wildcat producer opened a new pool. Of the dry holes, 16 were in or near fields and 43 were wildcats. The total reported initial daily production of the oil wells was 9013 bbl., averaging 252 bbl. per well. Active drilling operations numbered 65 at the close of the year, compared with 26 at the beginning.

Jan 1, 1935

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By J. H. Hedges

During the World War Leadville was an important producer of manganese and maganiferous ores for then steel industry. Normally, the market for these ores is limited to the requirements of the local steel mill at Pueblo for low-grade ores used in making, basic pig iron containing 1 to 2 percent Mr and spiegoloison containing 20 percent Mn, but during the war and a brief period of postwar readjustment, a good deal of 25- to 40-percent manganese ore qua shipped to in-stern steel-manufacturing centers. Throughout the active life of the camp, manganiferous iron ore carrying a little silver and lead and sometimes as such as 35 percent Mn was chipped to load smelters for flux. The total reordered production is 936,024 tons of metallurgical ore shinned to steel mills and 2,576,514 tons of fluxing ore, much of it of metallurgical grade.

Jan 1, 1940

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

An assessment of methods currently available for the accurate determination of low concentrations of platinum in ores and mineral concentrates indicated that prior treatment of the sample by fire assay procedures is necessary. To enable rapid determinations to be carried out, instrumental methods applied to the metallic bead produced from the fire assay treatment have been evaluated, considering maximum flexibility for concentration variations, minimum chemical operations, and adequate sensitivity.Atomic absorption spectrometry proved suitable, giving solution determination limits of 0·4 p.p.m. Pt, 0·1 p.p.m. Pt, or 0·06 p.p.m. Pt under various extraction conditions using aqueous and organic agents. Thesedetermination limits related to 1 assay ton of sample (32·67 g) produced easily readable and accurate readings within the range of platinum contents (0·03-2·0 p.p.m.) of economic interest in deposit evaluation and prospecting. The technique shows promise of also being suitable for determination of palladium and gold.

Jan 1, 1970

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

The Purification of Low-Grade Quartz Ore by Flotation and its Mechanism

Sep 13, 2010

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998