Search Documents

By Roe-Hoan Yoon

"Industrial flotation columns often suffer from low recoveries and high maintenance requirements because of poorly-designed air spargers. The MicrocelTM bubble generators were developed at Virginia Tech to overcome these problems. In this system, small air bubbles are generated by circulating a portion of the flotation pulp through a set of static in-line mixers. The small bubbles improve flotation kinetics and allow a higher recovery (or capacity) to be achieved. Other advantages of the system include reduced air consumption, plug-free operation and on-line maintenance. This article discusses the advantages of the MicrocelTM bubble generators and presents examples of successful in-plant demonstrations.IntroductionColumn cells are widely accepted in industry for cleaner operations because they are more selective than mechanically-agitated conventional cells. The improved selectivity can be attributed to the use of wash water which minimizes the entrainment of fine gangue particles into the froth product. Columns may also produce higher recoveries if the air sparging system is properly designed and steps are taken to minimize back-mixing. Furthermore, the quiescent conditions afforded by column cells may be beneficial for recovering coarse particles that are readily detached from bubbles under more turbulent conditions. Also, properly-designed columns offer advantages in terms of savings in floor space, reduced operating and capital costs, and simplified circuitry.It is unfortunate, however, that some of the advantages of columns are not fully realized in industrial practice. Some column circuits are unable to achieve their design capacity, while others require extensive maintenance programs. These shortcomings can usually be attributed to deficiencies associated with the design, scale-up and operation of the air-sparging system. In this article, some of the basic problems associated with commercial air sparging systems are discussed and alternatives are suggested."

Jan 1, 1994

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

Organization Place Date 1919 American Electrochemical Society New York, N. Y. Apr. 3-5 American Chemical Society Buffalo, N. Y. Apr. 8-11 National Foreign Trade Council : Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y: May American Institute of Electrical Engineers Lake Placid, N. Y. June 23-27 American Society for Testing Materials..: Atlantic City, N. J. June 24-27 American Railway Bridge and Building Association Cleveland, O. Oct. 21-23

Jan 4, 1919

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in'progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America.The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By J. Davis, M. G. Reading

"INTRODUCTIONInternational Minerals and Chemical Corporation (Canada) Limited operates two potash mine/refinery complexes near Esterhazy, Saskatchewan. Annual production of approximately 4.2 million tons is sold in the United States and overseas in five grades according to size and quality.Ore grading 25% K2 0 equivalent is mined from a horizontal bed by continuous boring machines, crushed, and hoisted at 8 inches. The refinery operation consists of the eight basic steps shown in Figure 1. Particle sizes handled are similar to those experienced in other forms of mineral beneficiation: 8 inches to 100 mesh. The ore is crystalline and particles are angular. Fortunately the major mineral constituents, sylvite (KCl) and halite (NaCl), demonstrate relatively low hardness at 2 to 2.5.Therefore, while simple abrasion must be acknowledged, it is not a major problem except, of course, in circuits carrying magnetite.Corrosion, as represented by the classic equations of Figure 2, occurs in all its various forms."

Jan 1, 1983

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By Monger N. R

Factors leading to the decision to use Joy Continuous Miners for pillar extraction in the Burwood Colliery are outlined. A detailed description is given of the Joy 1-CM-2 Continuous Miner, including the power supply to the machine, and the method of cutting coalfrom a face. Modifications found necessary in practice are dealt with.The Joy 10 S.C. shuttle car used in conjunction with the Miner, and alterations made to this unit, are then described, together with Ancillary units for the whole installation such as transformers, motor generator set, air compressor,_ cables for power supply and water supply for dust suppression.Special arrangements were necessary to transport the Miner and Shuttle Cars through the tunnel to the Victoria Tunnel seam, and the method of overcoming the transport difficulties is discussed. Manning of the Continuous Miner unit, and final preparation andsubsequent working of the pillars is outlined. Special attention must be given to maintenance of the machines.It is concluded that the combination of Joy Continuous Miner and Shuttle Car is an excellent method for removing pillars in the Burwood Colliery.INTRODUCTIONThis paper deals with the Burwood Colliery in the RH.P. Group in which some units are engaged in the mechanical extraction of pillars with Joy Continuous Miners.In 1941, an amendment to the Coal Mines Regulation Act of N.S.W. forbade the extraction of pillars by mechanical means unless with the express permission of the Minister for Mines. As this permission was not forthcoming, no mechanical extraction of pillars took place in Australia until 1954 As it was doubtful during most of this period whether mechanical extraction would ever come about, coal generally was won with a view to maximum extraction in the first workings, thus giving rise to centre gannon bord panels and 45° angle cut throughs as shown in Fig. 1.

Jan 1, 1957

By J R. Lang, J K. Mortensen

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addition to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971