Search Documents

By John S. Hutchins

Two potential modified in situ methods are described for recovering the 68% "unrecoverable" hydrocarbons in oil reservoirs. For the 300 billion barrels of conventional light crude a Drip Drainage system is suggested by mining underneath a reservoir and producing from below by controlled gravity flow. For the 200 billion barrels of heavy or viscous oil and tar sands deposits a Flip Flop process is described using surface flooding with hot water saturated with surfactant and weighting additives. Mining engineering description of shafts and tunnels required are included as is discussion of the tunnel proximity to a reservoir. Petroleum engineering flow equations to describe production rates and candidate reserve areas of the U.S. are described. DCF economics are provided to indicate that current oil prices may be sufficient to commercially develop these recovery methods.

Jan 1, 1978

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By M. Maier

Geographic Information Systems (GIS) has evolved into a powerful tool for analyzing spatial and attribute data in many industries including mining. Modern field data collection techniques add another dimension to the use of data in the field and enhance the utilization of GIS for mining applications. This discussion will review how field data is collected and how office data and maps can be taken into the field to be analyzed and verified using pen-based computers and differentially corrected GPS.

Jan 1, 2001

By David Hill

The Australian underground coal mining industry is increasingly operating in an environment that challenges traditional concepts of coal pillar design, against a background of heightened expectations and demands from other stakeholders with regard to the protection of both natural surface features and burgeoning civil infrastructure. The result is greater possibility of conflict between mine operators, developers and regulatory bodies, with potential for unnecessary sterilisation of Australia?s coal resources and/or escalating surface development / infrastructure protection costs. On the positive side some significant advances have occurred in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some current issues in coal pillar design, focussing particularly on the application and limitations of analytical models of pillar loading. Established methodologies are reviewed and alternative approaches explored, including examples of key geometrical, geological and probabilistic concepts. Practical experiences from the Southern Coalfield of New South Wales (NSW) are examined for the purpose of highlighting critical variables. Finally, some suggestions are made with regard to the direction and opportunities for future research, with particular regard to coal pillar loading, in the interests of all stakeholders.

Jan 1, 2008

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Mike Watts

Since the first longwall panel development started in the new mining, (Southern) area, a number of roof falls have occurred in L1 and L2 gate-entries. The longwall was delayed for a total of two months due to roof falls in the gate-entries. To prevent roof falls in future gate-entries, an extensive ground control analysis has been conducted which incorporated regional horizontal stress and panel orientation, tectonic stress, roof strata, surface stream valleys, etc. Results of the analysis indicate that a combination of these factors caused the roof falls. Therefore, a Roof Instability Rating (RIR) system was constructed to predict the roof condition and identify areas where supplemental support should be implemented. The L3 gate-entries, supported by the prediction using the RIR system, have not experienced any roof problems.

Jan 1, 2000

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Jeffrey C. Hillman

The need to recruit locally produced engineers by the South African Mining Industry led to the Engineering Faculty at the University of the Witwatersrand developing a number of academic bridging initiatives for educationally disadvantaged students. The graduation rate achieved during the initial five years of operation by the most successful of these programmes has been on a par with that of al other students but the performance of subsequent intakes has declined to such an extent that the continuance of this scheme could now be at risk. One reason for this reduction in throughput is that many of the applicants for the increasing number of mining bursaries have been more interested in the bursary than the profession and have either failed or dropped out due to a lack of application and motivation. This will have serious consequences for both Wits and the Industry if it continues and some method of identifying unsuitable or suspect applicants needs to be introduced as a mater of urgency. It is recommended that an introductory course be set up at a working mine that would be run under the auspices of Wits, as a joint venture with industry, and include a level of academic input that would provide both bridging needs and certain first year credits. The final form of this course will require extensive consultation with al parties but needs to be completed before the end of 1996. It is further recommended that the advertising and promotion of mining careers be expanded and much improved.

Jan 1, 1996

By Fred D. Fox

Introduction Abandoned mill tailings deposits can be found throughout the northern Black Hills of South Dakota, indicative of mining activities that originated during the great gold rush days of 1875. The Refuse Act of 1899 attempted to regulate the deposit of debris from mines and stamp works. But, in most cases, huge volumes of mine and milling wastes were disposed of in ways no longer considered environmentally acceptable. Restoration of gold mill tailings deposits is a relatively new practice to the Black Hills area. This discussion will present an overview of the environmental setting, environmental problems associated with past tailings disposal practices, practices being implemented to solve these problems, and prospects related to present the future tailings disposal practices. Environmental Setting An understanding of climatic characteristics, geology, surface and ground water hydrology conditions, and the physical and chemical characteristics of selected mill tailings deposits will aid in understanding environmental problems associated with tailings disposal and restoration. Climate The Black Hills region is in the middle latitudes, which have a

Jan 11, 1984

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By Q. Lui, J. Oxenford

The occurrence of heavy minerals in the oil sands of Alberta has long been known and has been well documented in the literature. Unfortunately most of the researchers working on this resource have been unable to produce products that meet acceptable market specifications. This has resulted in many misconceptions about this resource. Recent efforts have shown that with some innovative approaches, marketable material can be produced and as a result it might finally be possible to realize the potential of this immense resource that, some have estimated, could contain in excess of 20% of the world demand by 2010. This paper highlights the uniqueness of this mineral assemblage and the mineral processing challenges it presents. It shows the most recent work that has resulted in the production of marketable titanium and zircon products. This paper also focuses on some of the special problems resulting from the variability in the heavy mineral suite. Of special interest is the occurrence and removal of bitumen and pyrite without adding to the sulphur dioxide loading in the regional airshed. The trend by the mining industry to develop various positions on ‘sustainable mining’ has some significance for the heavy mineral industry. Although the industry generally has an excellent track record of eventually rehabilitating disturbed ground in an acceptable manner, heavy mineral mining operations tend to have a relatively large footprint of disturbance and the industry is under considerable pressure to develop options that are more environmentally acceptable. In addition, as operators move to exploit deposits that are lower grade and/or are further from a port site, the emissions per unit of sold product will also rise and the industry will be under pressure to address this issue as well. Because heavy minerals from oil sands are by-products of existing operations, there are virtually no incremental disturbances or emissions that would be associated with heavy mineral production. All mining and tailings remediation issues are accounted for by the oil sand operation. The only incremental emissions would be those associated with the mineral processing operations and transport of finished products to a port site. This paper discusses the environmental and cost implications of this situation.

Jan 1, 2003

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004