Search Documents

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By Toshiharu Hayashi

We prepared the water dispersed with Au particles ranging from 10 to 20 nm size by a novel wet chemical synthesis; generating seeds of Au cluster by adding a borane dimethylamine complex into chloroaureic acid (gold salt) solution, and then growing simultaneously with aminoalcohol included in the solution. As-prepared Au nano-particles with chemical surface modification were found to have some attractive performances, i.e., showing a high dispersiveness in an aqueous solution in a long time, sintering nano-particles at low temperature, and having low resistivity in the film prepared from nano-particles. In the case that smaller Au nano-particles were removed from as-prepared colloid, especially, Au thin film formed on the surface of Si plate showed the excellent value of 7.0x10-6ohm cm (reference peculiar resistance: 2.35x10-6 ohm cm).The sintering temperature was dependent on the elimination of 2-aminoethanol that modified on the surface of Au nano-particles.

Jan 1, 2006

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By Shigeo Asai

History of EPM is described and several functions utilized in EPM are reviewed. Main activities of EPM are summarized with the view on mass production and applications of high magnetic field related to nano-technology. Future trends and prospects of EPM are discussed.

Jan 1, 2006

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By Sharon K. Young

What might an ideal leach-to-cathode/product system look like in the next century? The paper looks at the synergies of the 60's and 70's that led to the highly effective copper leach SX-EW system of the 90's. Standing in the year 2020 focuses on what breakthrough technologies might make possible a next generation leach/extraction/metal recovery system. Many of the pieces of such a technology have been developed, even piloted: in situ leaching, enhanced bioleaching, heap leaching of fine particles, resin in pulp, ion exchange, alternate anode reaction electrowinning, novel anode coatings. With nearly non-existent research on the part of individual large companies, the greatest challenge may not be inventing the technologies but rather inventing an industry "will to create."

Jan 1, 1999

By C. M. Acuña

Copper losses in slags are of great concern, specially in smelting and slag cleaning processes. It is widely accepted that the suspension of metallic copper and matte droplets is strongly affected by the viscosity of the slag. The Chuquicamata Division of Codelco- Chile produces concentrates high in zinc, an element which reports mainly to the slag phase. The ZnO may affect the viscosity and therefore the copper losses. This work aimed to investigate the effect of lime to control the viscosity of slags, and in turn to control the copper losses. By using the experimental viscosity data and the Stoke's law, the settling rate of matte prills in various slags was estimated. The results indicate the possibility of increasing the recovery of copper and/or decrease the process time.

Jan 1, 1999

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

By M. Somerville

In 1989 CSIRO Minerals initiated investigations into continuous converting of copper matte into low sulphur blister in Sirosmelt type reactors. Following the successful piloting of this processing route, some effort was directed towards a single stage copper making process where copper metal is made in one step from concentrate. The aim of the project is to develop a continuous process, which offers considerable environmental and economic benefits over conventional copper making processes, which use Pierce-Smith converters. In the selection of the optimum flowsheet a number of slag treatment options have been considered and tested. These unit operations include: leaching and electrowinning, flotation-leaching-electrowinning and flotation with recycling of recovered copper through the smelting vessel. In this paper the suitability of these process options are evaluated using the available information and recently measured copper recoveries from our testwork at CSIRO. The operating and capital costs of the various options have been estimated using Aspen Plus simulation procedures. The most attractive flowsheet in terms of capital and operating costs is the treatment of slag using mineral processing techniques and the recycle of a copper slag concentrate to the smelting vessel. It has been found that the chemistry of the slag being treated has a large bearing on the recovery of copper in flotation and hence on the economics of the process.

Jan 1, 1999

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By Daniel Kittelty

A fully instrumented laboratory electrowinning cell has been used to produce nickel cathodes from synthetic solutions containing various impurities in order to evaluate the effects of both metallic ions and organic reagents (from prior solvent extraction and other processes) on the quality of the electrodeposited nickel. The conditions used were typical of those employed in industrial electrowinning operations. The impurities were found to alter the crystal size and shape, induce the development of hydrogen pits on the deposit surface, incorporate as metal hydroxide crystals in the deposit, and alter the internal stress and current efficiency. These effects have been interpreted in terms of previously established relationships between the solution composition and the physical properties of the cathodes. The incorporation of the common metal impurity ions into the deposit have been interpreted in terms of a mass transport controlled reduction or precipitation reactions. In particular, a low concentration of aluminium ions resulted in an initial highly deleterious effect, which was replaced by a positive influence at higher concentrations. A model which involves the buffering effect of the aluminium on the pH at the cathode surface has been proposed.

Jan 1, 2003

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By D. A. R. Kay

Phase stability diagrams are used to predict the abilities of lanthanum and cerium oxides to desulfurize coal gasification products in the temperature range 800-1000 C. Results of desulfurization studies in laboratory fixed bed reactors illustrate the effects of i) sorbent preparation, ii) input gas quality and iii) temperature, on the desulfurization reaction. 2CeO(2-x)(s) + H2S(g) + (1-2x)H2 = Ce2O2S(s) + 2(1x)H2O(g) The results of desulfurization/oxidation regeneration cycles are also reported.

Jan 1, 1989