Search Documents

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with' less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By M. Jortikka

The smelting process of the old reverberatory furnace including its capacity has been improved over the years in different ways eg. with oxy-fuel burners, parallel reactors with the reverb or with various modifications of the reverb furnace itself. The future reverb modifications with old concepts are difficult or impossible as the increased copper losses in slag call for separate slag treatment and particularly the process modifications do not solve the environmental issues but instead mean unavoidable high capital and operating costs in gas cleaning and sulphur recovery. During the last decades improvement in process performance and increase in capacity of copper flash smelters has been achieved easily by substituting the pre-heated process air by highly oxygen enriched air. The flash furnaces of today, however, are inherently designed to operate with high oxygen enrichment. Further process improvement with a view to production costs and capacity increase as well as to the more stringent environmental requirements is possible with even higher oxygen enrichment. This, apart from the advantages it generates, requires improvements in and careful design of the feed system, concentrate burner, furnace cooling and the off-gas line as well as adaption of the flash converting instead of the conventional Peirce-Smith converters. A logical answer even for the revamping of the reverb smelters in the future is the total replacement of the reverb furnaces with flash smelting together with flash converting. This paper discusses the possibilities for future process improvements of the existing flash smelters taking into account the process concepts, equipment modifications and capital aspects not forgetting the environmental issues. The revamping of the PASAR smelter in Philippines is introduced as an example of a recent success story.

Jan 1, 1994

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By Elders. Wilfred A.

Petrological and geochemical methods, the utility of which has long been established in the mining industry, are proving useful and cost-effective in elucidating the thermal evolution of active geothermal fields. In return, they yield insights into sulfide-silicate equilibria, mass and energy transfer in convecting hydrothermal systems, and the genesis of hydrothermal ore bodies. Within the Plio-Pleistocene sediments of the delta of the Colorado River, in the Salton Trough, several active geothermal systems are known. Temperatures vary from 100-365°C, at less than 2 km depth, and salinities vary from 3,000 to 280,000 ppm, total dissolved solids. The hydrothermal alteration causes marked induration of the sediments, producing greenschist facies metamorphic minerals, including hydrothermal ore minerals. Subsurface authigenic minerals show strong correlation with increasing temperature. A typical sequence in sandstones is (below 150°=C) montmoril-lonite-kaolinite, (above 180°C) chlorite + illite, (above 225°C) calc-alumino-silicates, (above 325°C) biotite. There is a transition from porosity-dominated\to fracture-dominated permeability in the hottest and deepest geothermal reservoirs. This regular series of minerals provides a practical tool during exploration drilling. From drill cuttings, we can make predictions on reservoir temperatures, useful in making decisions on well completion. Other types of geothermometry we have employed include light stable isotopes, fluid inclusions and vitrinite reflectance measurements. A combination of these techniques not only improves our temperature predictions, but together with fission tack annealing studies, permits us to model the dynamics of temperature change and fluid flow in these geothermal reservoirs.

Jan 1, 1981

By T. V. Jayaraman, D. Das, B. Mallesham, A. R. James

The PNN-PZT xPb(Ni0.3Nb0.67)03-(1-x)Pb(Zr0.31 Ti0 69)03 (0.2=x=0.6) based relaxor-ferroelectric material was synthesized by colurnbite precursor (NiNb206) method via conventional solid state reaction. Homogeneous mixture of required oxides and precursor was calcined at 850°C for 4 hrs to obtain phase pure perovskite. Pellets of PNN-PZT ceramics were sintered at 1100oC for 4 hrs. Phase pure perovskite structure was confirmed by the X-ray diffraction analysis. From the X-ray diffraction analysis it is also confirmed that there is a structural transformation from the rhombohedral to tetragonal with increase in PZT content and existence of morphotrophic phase boundary (MPB) at x = 0.5 composition. The morphology and microstructure of the sintered pellets were observed using the scanning electron microscope. P-E loop measurement shows the high remnant polarization (19.12 µC/cm2) and low coercive field (6.89 kV/cm) at MPB compared to all other compositions. The electromechanical planar coupling coefficient (kp) was measured through the resonance and anti-resonance method using the LCR meter. The piezoelectric strain coefficient (d33) measured directly using the d33-meter. At x = 0.5 composition the highest value of d33 = 398 pC/N is obtained.

Jan 1, 2012

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04' pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By Hao Rang

The article Is specially to Introduce the recovery process of Nb, Mn, P from slags and reutilization techniques of the remaining slags. Nb-Mn-Fe alloys which contain 14-16% Nb, 40-60% Mn can be obtained after using fire refining process of " Blast Furnace-Revolving Furnace-Electric Furnace -Electric Furnace, "meanwhile, phosphorous slags which the content of phosphorus pentoxide Is 29.21%. Further going through wet metallurgical processing and electrowinning technics to recover grading 99°o metallic manganese. Finally, phosphorous slags are grinded finely to be as phosporous fertilizers to be directly used for farmlands. Small particle size (0-8mm) rich slags are mixed with slight solid additions for balling directly, and taken Into blast furnace with blocky slags all together. The remaining tall slags are fully used as constructional materials, slags cement as well as a serial of wall materials, road materials, ground ornamental materials without burning operation and steam curing. The compressive strength range of those materials is up to 15-30 MPa. There is no more solid waste slags effluent In the full technical process.

Jan 1, 1994

By Pavol Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for the end users and pump manufacturers due to the undesirable outcome of unstable pump performance. Most of these challenges occur due to incorrect pump selection and suction tank design. The traditional approach is to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve the mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance. This paper examines the flotation process in detail and how froth pumps are designed to handle this arduous process.

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By Yu Yamashita

There have been increasing in melting recycled scraps in copper smelting processes, and thus growing interests in the chlorine behavior. In this study, chloride dissolution in FeO-Fe2O3-SiO2slag (SiO2sat.) at 1523 K has been measured with varying in PCl2 from 1.13x10-8 to 1.30x10-7atm. and the oxygen partial pressures encountered in typical copper smelting furnace, i.e. PO2=10-8 to 10-10 atm. Discussion is made on the chloride capacity of FeO-Fe2O3-SiO2 slag in terms of its characteristics and the dissolved chlorine species. It has been shown that the mostreasonable dissolution reaction and chloride capacity can be expressed by the following reactions, where chlorine dissolves in the form of Cl-; here, aO2-, oxygen ion activity, is shown a function of oxygen partial pressure in the atmosphere. [ ]

Jan 1, 2006

By E. Burgos Cruz

The behaviour of S, N and P during refining of Fe-18 wt%Cr-10 wt%Ni with calcium carbide was investigated. The effects of the initial contents of C and N in the metal phase, as well as the supply method of calcium carbide to the melt on the removal degrees of S and P were evaluated. Heats were carried out at 1873K, in MgO crucibles, using a laboratory induction furnace. It was observed that simultaneously with S and P, N and O have also participated in the reactions. It seems that, in fact, O governs the behaviour of the other elements dissolved in the melt and that N is had to the removal of P with calcium carbide. It was also noticed that high C content in the metal phase have not altered the dephosphorization and desuffirization degrees, but that the supply of calcium carbide done by injection led to a lower dephosphorization degree than the one obtained by dumping it.

Jan 1, 1995

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By A. Alvarez

In this work, mesophilic and thermophilic cultures have been used in the presence of silver as a catalyst. Chalcopyrite and byproducts of bioleaching were characterized in order to: a) obtain information about the kinetics control of the process, and b) explain the different behaviour observed during the mineral attack. With thermophilic microorganisms (68°C and Norris medium as nutrient) the reaction stopped at approximately 65% copper extraction, with and without Ag ion addition as a catalyst. The remaining chalcopyrite appears surrounded by hydronium jarosite (with ammonium ion in substitution in the "alkaline site"), goethite and elemental sulphur. With mesophilic cultures (35°C and 9K medium as nutrient) the reaction stopped at approximately 25% copper extraction (without Ag) and approximately. 85% extraction (with Ag). In both cases, the remaining chalcopyrite was surrounded by agglomerates of ammonium jarosite (with hydronium ion substitution in the "alkaline site") and some iron oxides and/or hydroxides.

Jan 1, 1999