Search Documents

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009

By Jennifer Murphy, Brad S. Schake, Karol Holmes, John R. FitzPatrick, Mike H. West

"The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps.We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (1 DO-gram) flow experiments, using depleted uranium, were done after the small-scale evaluation of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos.Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process.Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail."

Jan 1, 1996

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By G. S. Hanumanth

Sedimentation of particles during the liquid metal processing of particulate metal-matrix composites can affect the homogeneity, and thereby the properties, of the cast product. A novel electrical probe has been developed to measure the in-situ volume fraction of ceramic particles in molten metal baths. Using this probe, sedimentation rates for 90 pm silicon carbide particles dispersed in molten aluminum A356 alloy were measured over a wide range of particle volume fraction, 0.05 to 0.3. The sedimentation rate was found to depend strongly on particle volume fraction; the time to clarify a 0.15 m depth increased from approximately 60 to 500 seconds as the volume fraction increased from 0.05 to 0.3. Measured sedimentation rates agree well with the predictions of a sedimentation model based on one-dimensional, two-phase flow theory in which the inter-phase drag function is derived from the momentum equation, utilizing the Richardson-Zaki Equation for sedimentation in aqueous systems. The implications for solidification are discussed.

Jan 1, 1993

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By P. Aguirre

Recovery of zinc, copper and nickel from electroplating waste solutions was achieved 'by using a Pulsated Percolated Porous Electrode "3PE" reactor on a pilot plant scale. Intensity - potential curves were used to study the possibility of metal removal and to define the working potential range. The present study describes the use of the 3PE reactors in several electroplating industrial units for the decontamination of their effluents. These effluents were issued from different industrial solutions such as cyanide, sulfate, chloride and Watts baths. Using the stripping curves, deposition rates and electrical efficiencies were determined as function of the metal concentrations in these effluents. Their decontamination could be achieved to the level of few ppm of metals with reasonable current efficiencies. The recovery rates of zinc and copper were about 93 and 99 %, respectively. The. treated effluents contained less than 7 and 1 % of the initial contents of Zn and Cu, respec¬tively. This process allows the recycling of the recovered metals and leads to water saving.

Feb 13, 2014

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200,000t-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced. The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 2001, As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By Feng Chen, Lirong Chen, Yufeng Guo, Wenjie Weng, Tao Jiang

"In this paper, the carbonthermal reduction behavior and the influencing factors of Panzhihua ilmenite under the condition of carbon-burdened were systematically investigated. The results show that the ilmenite forms into titanium nitride during the reduction process at 1200 °C under the condition of carbon-burdened. Carbon-burdened is beneficial to the reduction of iron oxide, but less favorable for the growth of iron grain.IntroductionThe titanium ferrous resources are very rich in Panzhihua-xichang area, accounting for about 38.85% of the world's proved reserves [1]. However, TiO2 grade of this kind of ilmenite is low and calcium magnesium content is high, it generally requires preconcentration to titanium-rich material—titanium slag or synthetic rutile.Chlorination process is an advanced method for production of titanium dioxide, which should takes high quality titanium-rich material with low content of calcium and magnesium as raw materials (the content of MgO and CaO are less than 1.0%). Ilmenite in Panxi area, however, contains high calcium and magnesium; it is not suitable as a raw material for chloride process. Methods of producing titanium-rich materials which have been applied in industry are electric smelting, various acid leaching and reduction rust [2-5]. There still exist some problems such as CaO and MgO removed not thoroughly, low resource utilization, high energy consumption and environmental pollution."

Jan 1, 2012

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000