Search Documents

By Soumitro Nagpal

Bacterial oxidation of a pyrite-arsenopyrite-gold ore concentrate was carried out in .14-liter continuous-flow stirred-tank reactors (CSTR). Oxygen and carbondioxide consumption rates mineral dissolution rates, and bacterial concentrations were measured at various steady-state residence times and with 6, 11, and 16 wt.% solids in the feed slurry. A sharp optimum in biooxidation rate .was found at a residence time of approximately 40 hours for operation at each of the three pulp-densities. Biooxidation rates increased consistently. with increasing pulp density. Cell washout accompanied by negligible biooxidation rates was found to occur at a residence time of approximately 20 hours. Mineral' oxidation was found to be strongly dependent on bacterial activity. Arsenopyrite was found to be preferentially oxidized? at the higher Pulp densities.

Jan 1, 1991

By C. Schwandt

Recent research work has led to the development of a new electrochemical hydrogen sensor, which is based on a proton conducting solid electrolyte in conjunction with a self-contained solid hydrogen reference standard and is operated at elevated temperatures. The incorporation of the internal hydrogen reference renders the sensor versatile and user-friendly and makes it attractive for practical exploitation. The present article focuses on the utilisation of the sensor as the integral part of a probe for the quantitative determination of hydrogen in molten aluminium and aluminium alloys. The main features of the sensor and the probe as well as the measuring technique are discussed. Experimental results obtained with the novel analyser in trials under industrial conditions are presented and highlight the good performance of the device.

Jan 1, 2003

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Kensuke Sassa, Shigeo Asai, Norihisa Waki

"A new method for separating inclusions from a molten metal using a high magnetic field has been proposed. The principle of this method based on the magnetization force has been confirmed in experiments of separating intermetallic compounds imitating inclusions from molten Al-Si-Mn-Fe and Al-Si alloys. In order to measure a magnetic susceptibility, the Gouy's method has been so modified by using a super-conducting magnetic as to work in a high temperature up to 1473K. A theoretical expression for the magnetization force, which is indispensable to evaluate the magnetic susceptibility, has been derived. The magnetization forces acting on intermetallic compounds which were used in the magnetic separation were measured over the range of liquidous to solidous temperatures and the magnetic susceptibilities of the intermetallic compounds were obtained from measured magnetization forces by use of the theoretical expression.I. IntroductionRecent developments in the technology of super-conducting magnets have given rise to the circumstance that a high magnetic field over a relatively large space is readily available without liquid helium. Then, it has been found that a high magnetic field provides magnetic effects to nonmagnetic substances and various interesting phenomena have been reported in the broad science fields of physics, chemistry and biology1). ""A science related to a high magnetic field"" in which many fields are transversally viewed from the standpoint of a high magnetic field2 ) is going to be established. In particular, new phenomena and functions brought by the science related to a high magnetic field are also useful for Material Science and Engineering so that the creation of Materials Science and Engineering related to a high magnetic field"" has been conceived 3).Now, when a substance regardless of being magnetic or nonmagnetic is put in a magnetic field, it feels a magnetization force, which is familiar to such a force that a magnet attracts iron. The force is in proportion to the product of magnetic field strength, its gradient and susceptibility so that a precipitated substance can be separated from a molten metal based on the difference between susceptibilities of a substance and a melt. This is a basic principle of the magnetic separation. So far the application of the magnetic separation has been limited to the separation of ferromagnetic substances from a nonmagnetic medium. A high magnetic field, however, has enabled to separate nonmagnetic substances from a nonmagnetic medium.In this study, a new method to separate inclusions from a molten metal using a high magnetic field has been proposed. The principle of the method was verified by experimental works and the feasibility on the elimination of inclusions in steelmaking processes has been studied"

Jan 1, 2000

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By Vadim J. Jabotinski

Electron beam processing is potentially very attractive for the high temperature treatment of hazardous materials. The very high power efficiency of the electron beam energy source (80- 90% of the power from the electric power line is converted to useable energy) is one of the positive features of this technique. This paper will consider advanced electron beam concepts for solid, liquid, and gaseous waste treatment such as stabilization of radioactive solid and liquid hazardous streams. Fundamental aspects and applications including an analysis of the economic potential of electron beam processing of waste treatment will be presented.

Jan 1, 2000

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"The use of electromagnetic field to remove suspended particles from metals such as aluminum by pushing to the boundary has been well studied. However, the potential of this method is yet to be exploited for the removal of inclusions from silicon. Considering the increasing amount of Top-cut SoG-Si scraps year upon year, there is the need to harness all the potentials of technologies to recycle this materials to ensure sustainability. This study investigates, and discusses new results on the effect of processing parameters such as composition, coil current, and frequency on the removal of inclusions from silicon under high frequency AC electromagnetic field.IntroductionThe solar cell silicon making industry requires pure and clean silicon in order to maximize the conversion potential of the solar cell material. The conversion efficiency of solar cells is limited by minority carrier recombination at dislocations and those intra-granular defects such as impurities, small clusters of atoms, or precipitates [1]. Recent global developments in the energy sector with a drive for the production of clean, reliable, and affordable energy have stirred a rapid growth in the production of photovoltaic (PV) cells.[2] Thus over the years, silicon based PV cells has seen a lot of growth as it has a PV market share of over 90 % [3] either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [4]. MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from the air absorption during solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [5]. For sustainability the silicon in the top-cut silicon scraps must be recovered. Therefore methods for removing non-metallic particles, such as SiC and Si3N4, from the silicon are important in order to recycle the top-cut scraps to a useful feedstock for the silicon solar cells manufacturing."

Jan 1, 2012

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

By M. Nishikawa

The Hachinohe Smelter employs the Imperial Smelting Furnace (ISF) for production of zinc and lead and handles a large number of concentrates and recycled materials. In recent years, recycled materials such as zinc-bearing materials, lead sludge and Waelz oxide have provided up to 30% of the feed materials at the plant. To allow for a satisfactory operation using such a wide range of recycled materials, the Hot Briquetting Plant was built in 1986 and started its operation in January 1987. In April 1988 the zinc production capacity of the ISP was increased from 81,000 to 101,000 tonnes per year. The additional production in the ISP has been attributed to the utilization of the hot briquetting process. This paper describes the various facts of the smelter, concentrating on hot briquetting operations and treatment of hot briquettes in the ISF.

Jan 1, 1991

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997